Repair in the hallway with your own hands. Budget renovation in the hallway. small hallway how to be

The hallway is being refurbished. The main reason is that all construction debris and dirt during the repair of all other premises will pass through it. Something in her will wake up, fall off, smear, and what will the face of the house turn into? So, with a more or less serious repair in an apartment, you should definitely think about repairing the hallway, especially since repairing the hallway with your own hands is not a technically difficult task, and professional high-quality inexpensive repair of the hallway is a fairly common service.

Choose, on their own or not, of course, the owners. But keep in mind that due to the small volume and surface area of ​​the premises, the cost of work will in no way be less than 50% of the total, i.e. when repairing the hallway by craftsmen from the outside, half of the payment will go to them for work. So look at your skill and budget possibilities. If you take it on your own, then you first need to know the features of the room.

What should be taken into account?

Hallways, as you know, are mostly small and cramped, without sources of natural light. Dirt is brought into the hallway, people walk on the floor in stiletto heels, and even on skates. Weights are placed on the floor in it, sometimes hard and angular. Spray from umbrellas, clothes, dusting pets fly onto the walls in the hallway.

A wave of cold air from the opened door can break into the hallway, and the relative humidity in it will immediately jump above the dew point. Condensation may not be visible to the eye, but it will remain in the cracks and pores of the finish, and will slowly do its destructive work: rot, mold, any infection.

But you want to have even a small corridor clean, bright, cozy, and not a dark, gloomy passage that immediately spoils the mood for yourself and your guests. This is quite possible if repair work according to a clear plan, in a certain sequence and with full knowledge of the matter, especially regarding the choice of materials.

Planning

The general sequence of planning the repair of the hallway, in order of importance of the stages, is as follows:

1. Lighting;
2. Organization of space;
3. Surface finishing;
4. flooring;
5. Furnishings.

The options for repairing the hallway depend primarily on its original layout with an explication - calculating the volume of the room, the area of ​​\u200b\u200bthe ceiling, walls and floor separately and the type of layout. The latter largely determines the choice of the nature of lighting, volumetric and surface design, and on them, in turn, depend technological features the work being done. Therefore, it is advisable to link the description of the repair to the most common types of hallways.

Types of hallways

AT typical houses the layout of the hallways can be divided into the following types:

• box;
• Corridor;
• "Nora with a snout";
• Coupe.

The hallway-box is typical for brick Khrushchev houses: from a small (about 4 sq. M) kennel, doors lead to a bathroom and living rooms; perhaps also in the kitchen, if the house was originally built for the “comrades” of the nomenklatura, i.e. superior. There are "boxes" both in stalinkas and in modern houses. Repairing a small hallway of this type is the easiest; furnishing is the most troublesome - because of the doors on all the walls, it is very difficult to put a typical wardrobe.

The hallway-corridor is most often found in panel house. The corridor is often narrow and long, so its decoration is of particular importance as a way of organizing space. Repair of a simple corridor - medium complexity. Hallways box and corridor are shown in the figure.

“Nora with a snout” is an indispensable attribute of a block Khrushchev: a narrow corridor past the nursery to the living room (hall) with a tap past the bathroom to the kitchen. Repair by design is quite complicated: narrow, cramped, how to organize the space, if there is just a little bit of it? It is still possible to do decently, given the orientation of the apartment to the cardinal points, see the corresponding section.

Note: they began to call the living room a hall just during the second wave of Khrushchev's housing construction, which was marked by a struggle against architectural excesses and the appearance of panel boxes with ceilings of 2.5 m and a total area of ​​​​up to 11 sq. m / person .. Etymology - black humor of new settlers.

The entrance hall forms the very first and, perhaps, the most important impression of the house as a whole. v

Of course, the very first room that visitors enter is the entrance hall. Therefore, it is very important that it is properly formatted. The entrance hall forms the very first and, perhaps, the most important impression of the house as a whole.

Therefore, the repair of the hallway must be approached competently and with due attention. Of course, many people mistakenly believe that it is easiest to do repairs in such an inconspicuous room. However, this is not the case at all. The fact is that the hallway performs several functions at the same time. Here it is necessary to place furniture, take care of the surface of the walls and floor. All materials should be very practical, because this is perhaps the most easily soiled area of ​​\u200b\u200bthe home. So, let's take a closer look at how to do it right hallway renovation. And so that our words are not unfounded, we will show you illustrative examples of the design of the corridor in the photo.

So, first you need to decide what kind of hallway you want to get. Now the choice of finishing materials is very diverse. Think carefully about what color, from what materials you want to decorate the front room of your house. And do not forget that the hallway should convey the meaning and mood of the design of the entire room. For example, more and more often natural or artificial stone is used to decorate hallways. It is practical, beautiful and durable. But there is also a minus - this is a very expensive coating. You can, of course, use wallpaper that imitates stone or brickwork. This option will also look great, the main thing is to choose the right color scheme.

Of course, it is important to take care not only of the walls, but also of the ceiling and floor. For the ceiling, modern masters offer many options. It can be ordinary plastering, and suspended or stretch ceiling. It all depends on your capabilities and imagination.

As for the floor, traditional laminate is most often used. It washes well and withstands external influences. Tiles are not entirely appropriate for flooring in the hallway. Often they make “warm floors” in the hallway, since it is from this room that it draws cold air. In any case, before starting the repair, carefully measure and correctly calculate the amount of material needed.

It is better for walls to choose either washable wallpaper or colorants. Liquid wallpaper - know-how, which is used to decorate the walls in the hallway. Such materials will allow you to forget about the new for a longer time. hallway renovation. After all, all the dust and dirt gets here directly from the street. That is why it is not recommended to use carpets on the floor.

Walls and ceilings should be leveled prior to applying the final coat. After leveling, you can start finishing.

Repair in the hallway: lighting

It is necessary to think about the lighting of the hallway. After all, this room, most often, is not equipped with windows, which means it does not receive natural light. It is important to understand that for different areas you need different lamps. After all, when entering the room, you should not experience eye discomfort. You need to take care of the light even before the start of finishing work. You may have to make additional wiring, which will hide behind the walls and ceiling.

If you have a small entrance hall, which is very common in our apartments and houses, lighting will also help visually enlarge the room. A lone light bulb hanging from the ceiling will obviously not play the best role for the implementation of your plans. Perhaps it is worth doing multi-level lighting. And it is better in such rooms to place lamps on the walls so that the light does not fall on the ceiling. It is good if there are enough glossy surfaces in the decoration of the room. This will only serve to benefit the overall picture.

If the hallway is narrow, place the lamps on only one of its walls. This will visually expand the space. And, of course, add mirrors to the interior. It is better to hang them at the top of the walls. To reduce the feeling of a tunnel in the hallway, place a lamp on the wall in its dark corner. That will be much better!

To increase the space is not necessary to use bright hues in the decoration of the room. You can simply use any of the listed design techniques. Of course, it is important to take care of the furnishing of the room. It is necessary to place hangers or even a wardrobe, a shelf for shoes and a mirror in the hallway. Be sure to use the space zoning of your hallway, even if it is not spacious enough. This can be done both with the help of furniture and through decoration. Just use materials of different textures or colors that serve to decorate different areas.

So, as can be seen from the above, hallway renovation- not so much simple task. And, if you are afraid to do something wrong yourself, seek help from specialists. They will give right advice and make your hallway unique and very cozy!

The entrance hall and the corridor can be called the “face of the apartment”, since it is they who form the first impression of the homeowners, of their tastes and well-being. Therefore, the design of these premises should be thought out carefully, to the smallest detail.

Finishing the corridor in the apartment is usually done last, since dirt and debris during the repair of other rooms will remain all the way from front door to the rooms where the work is done. In addition, when entering building materials or large pieces of furniture, they can easily damage the finishes on the walls and floors of the hallway. That is why the facing of these surfaces is performed last.

What should be considered when planning the finishing of the corridor?

Hallways in standard city apartments usually have a very small area without a source of natural light. Dust and dirt from the street are primarily brought into these walk-through rooms, as they are often walked in street shoes.

In addition, you should also think about the fact that during the operation of the apartment, various pieces of furniture and large Appliances, which during transportation it is quite possible to damage the surface of the walls. Therefore, for finishing it is recommended to choose materials that have a certain strength.

Another important point that cannot be ignored when planning the repair of these premises is that despite their small area, finishing work can result in a decent amount if they are carried out by a construction team. Therefore, having realistically assessed your strengths and financial capabilities, you can try to produce this stage on your own, choosing an affordable method and materials that are suitable in quality and price.

In order for the work to be successful, they should be carried out according to a pre-drawn plan, which should provide for the entire sequence of actions.

Work plan

The stages of repair work for any of the rooms of the apartment practically do not differ in their sequence, but they will differ in scale, depending on what type of repair is chosen: major or cosmetic.

• The overhaul involves the complete dismantling of coatings of all surfaces with the replacement of electrical wiring, the arrangement of a new floor screed and a plaster leveling layer on the walls. In addition, the total scope of work may include the installation of a false ceiling.

• Cosmetic repairs include the replacement of decorative wall and floor coverings, and sometimes the installation of a false ceiling. If ceiling work is to be carried out, then it may be necessary to make additional wiring for electrical cables for lighting fixtures that are built into the false ceiling.

So, the whole process of repair work is usually planned in the following sequence:

• For any type of repair - this is the dismantling of old decorative coatings and cleaning of surfaces, the removal of all previously performed leveling layers - with capital reconstruction premises.

• Carrying out the necessary calculations of the finishing area and the amount of materials required for it.
• Determining the location of lighting fixtures and wiring. Its connection to the mains is made already at the final stage of repair. Works related to electricity are recommended to be entrusted to a professional master who has the appropriate permit.

• Space planning, that is, determining the placement of furniture items necessary in the hallway, depending on the size and shape of the room. If it is possible to plan the premises using a special computer application, then this will be the best option, which will allow you to visually evaluate the color combination and the convenience of the proposed arrangement of all interior accessories.

• Finishing the ceiling, the chosen method and material - for any type of repair work.
• Alignment of walls, and then cladding decorative material at overhaul, or only finishing work for the cosmetic transformation of the room.
• Leveling the floor with a screed, and then laying the floor covering, possibly with a heating system - with a complete alteration of the rooms, or just replacing the decorative flooring during cosmetic repairs.

Types of hallways

The lighting and design solution for the design of the hallway largely depends on the type of hallway and corridor. With a standard layout, these rooms can be combined and have the following forms:

• A "box" is a square or rectangular room that provides ample room for imagination and can be decorated in any style. Such hallways are typical for houses of old construction and have an area of ​​​​4 square meters. m.

• The hallway-corridor is a narrow elongated rectangular room, sometimes having smooth turns at different angles, in which it is quite difficult to place a lot of furniture. Therefore, you will have to choose for her only the most necessary - it can be a shelf for shoes, an ottoman, a hanger for outerwear, and of course a mirror, without which you can’t do without in the hallway.

• Entrance hall - "boot" - this type of room also combines in its configuration two corridors located at right angles to each other. In one of them there are doors to the sanitary premises of the apartment, and it leads towards the kitchen, and in the other, in fact, there is an entrance hall with doors to the entrance and to the living quarters of the apartment. As a rule, these two corridors have a small width, but a sufficiently large length along which all the necessary furniture accessories can be installed.

What will be subject to reconstruction and decoration?

Hallway lighting and ceiling

After the walls are cleaned of old coatings, it is worth thinking about how to properly distribute the lighting fixtures in the dark hallway and corridor, since intense lighting is necessary for them. This factor is due to the fact that, as a rule, people do the final touches on putting their appearance in order when leaving the house in the hallway in front of the mirror. For this, it is necessary to provide that there is enough light in this room, and it is desirable to organize shadowless lighting.

If it is dark in a small room, then it will visually seem even cramped. To avoid this effect, it is recommended to make the ceiling light and install lamps on it that give a bright but diffused light.

If the ceiling is planned for painting, then the best option for this would be acrylic paint. However, this option will be advantageous only if the surface has perfect evenness and smoothness, otherwise bright lighting will reveal all the existing flaws.

AT last years plasterboard suspended ceilings have become popular, having one or more tiers, forming niches in which neon or led strip or the same lamp is installed. Most often, tiers are given intricate curvilinear shapes that visually expand the space, making the room look wider. In addition, a similar version of the ceiling will help to more intensively illuminate certain areas of the room, in particular the one where the mirror will be fixed.

If the apartment does not have too high ceilings, then you can use a glossy light stretch ceiling for their design. On its surface, light from devices mounted on the walls will be reflected, increasing the overall intensity of illumination. In this case, it is desirable to direct the light from wall sconces on a glossy surface.

original interior solution- two-tiered ceiling

If the owner of the apartment has good skills in working with building and finishing materials, he will be able to cope with this task on his own. To help him - a detailed publication of our portal

To obtain even bright light, it is desirable to use modern economical LED lamps, which today can be found in a large assortment in specialized stores. Such lamps, with a small power consumption, create an excellent level of illumination. Many of them are specifically designed to be embedded in drywall construction- they look like neat dots, which is why they are called dotted. In luminaires that turn towards the ceiling, lamps are installed that are equivalent in terms of luminous efficiency of 50 ÷ 60 W. If the sconces will be installed on the walls of a narrow hallway, it is recommended to choose flat models that do not protrude too much from the wall, otherwise they will visually make the room more cramped.

If the ceiling and the upper part of the walls are made light, then this factor will increase the overall illumination and help save on electricity consumption, since the effects of reflection of the light flux from surfaces are actively “turned on”.

If the ceiling in the hallway is not too high, then you should not use low-lowered lamps or chandeliers for lighting, as they will visually make the room even lower.

If you have the financial capacity, you can install a stained-glass suspended ceiling in the corridor, illuminated from the inside. But it should be remembered that in these conditions it is not worth choosing a pattern with a dark colors, and to organize the backlight it is better to use lamps with a cold glow.

In addition to the ceiling surface, recessed fixtures are sometimes installed in walls if they are sheathed with plasterboard, which is fixed on a metal profile frame, or placed in niches.

Drywall prices

drywall

Drywall - the best material for leveling walls

If the area of ​​\u200b\u200bthe room allows, then this method becomes the most convenient to implement, and all work can be done independently. More about - in a special publication of our portal.

Hallway flooring

The corridor and the entrance hall are the premises with the highest intensity of movement of the residents of the apartment. In addition, we must not forget about the dirt and dust brought on the shoes, which may contain grains of sand that can damage some coatings with their abrasive action. Therefore, for flooring in these rooms, you need to choose a material that has increased strength.

most popular floor coverings used in apartments are materials such as linoleum, ceramic tiles and laminate. You can rarely find parquet or massive board. Each of the coatings has its own characteristics, which you need to know about in order to choose best option.

Ceramic tile

The range of this material in hardware stores is quite wide, but not every type of tile is suitable for the hallway.

It is impossible to purchase tiles intended for wall cladding for laying on the floor, since there are completely different indicators of strength and wear resistance.

For laying near the front door, you should not choose a tile with an absolutely smooth glossy surface, since if you step on it in wet shoes, you can easily slip and get a serious injury. Especially this factor must be taken into account if the family has small children or people of respectable age. If you plan to lay this particular material, then the best option would be to choose a tile with a rough surface - this is usually indicated on the packaging of the material.

In addition, we must not forget that ceramics is a “cold” type of flooring and it is best to mount it on a pre-laid system. For apartment conditions, an electric heating option with a cable or special mats is suitable. These systems are safe to operate and consume a minimum amount of electricity.

The advantages of tiles include ease of maintenance, durability and long service life. However, this material is quite difficult to install, and if there is no relevant experience in this area, then you will have to invite the master, and this is also an extra cost.

Tiles can be combined with other floor coverings such as linoleum, laminate or even carpet. Thus, it is possible to divide the hallway into zones. One of the common options is that ceramic tiles are laid near the door, and the rest of the hallway and corridor are lined with other material. Such a decision will make these rooms less boring, especially if the design of the material is chosen with taste.

Laminate

Linoleum

Linoleum is a traditional flooring material for flooring in all rooms of the apartment, including the hallway, and it can be called time-tested for its practicality. If earlier this type of coating did not differ in variety in terms of base and colors, today its range pleases consumers, as it provides an opportunity to choose according to such criteria as the material of manufacture, the degree of wear resistance, pattern, thickness, colors and, of course, price.

If financial opportunities allow, then you can purchase a natural-based laminate.

It meets all the requirements for its operation in walk-through rooms - these criteria include environmental friendliness, moisture resistance and strength, high resistance to mechanical damage, low thermal conductivity, ease of maintenance and durability. The disadvantage of any natural material is its high price.

Artificial linoleum is made on the basis of polymer raw materials and has more diverse colors and patterns than natural, as well as quite affordable cost. The service life of this coating may vary, depending on the quality of the material, but in general its operational period is quite long, and is at least 15 years under normal conditions. temperature conditions. The disadvantages of artificial canvases include instability to solvents and sudden changes in temperature.

Decorative plaster

This type of finish is more complex in execution, but, despite this, it is becoming more and more popular, as it perfectly transforms the walls and hides small flaws on it. There are a lot of varieties of decorative plasters, but they all have high strength and abrasion resistance, good moisture resistance.

Decorative plaster - stylish decoration interior!

It is simply impossible to tell in one section about all types of this finish. You can get acquainted in detail not only with the description of different types, but also with the processes of preparing surfaces and applying finishes to the wall in a separate article of the portal.

The technology of finishing the walls of the corridor "under the stone"

In combination with plastered sections of the wall, laying tiles that imitate natural stone are often used, and more and more apartment owners are interested in this way of decorating the walls of the hallway. Therefore, two different technologies for finishing walls “under the stone” will be considered below. Perhaps the description of these works will inspire someone to an independent creative process and help save a decent amount.

Indeed, a properly selected stone texture and color scheme of this facing material can ennoble the interior of the premises and give it individuality. However, it should be noted that if the hallway has a very small area, then you should not stick stones on all the walls. It will be enough to cover only the area around the front door with stone, and it is desirable that the material had one of the light color shades.

Below, two available technologies for such a corridor finish will be considered step by step.

Laying tiles imitating natural stone

First of all, ready-made facing stone can be purchased at a hardware store. In this case, the work is carried out in the following order:

Illustration
	In order for the tile to hold securely on the wall, it is necessary to make a series of preparatory work, which begin with cleaning the walls of old coatings. It should be remembered that it is impossible to glue tiles on wallpaper, even if they are securely attached to the wall, since the canvases will not be able to hold heavier finishing material. However, if you plan to lay on separate parts of the wall, you will have to develop a design project in advance, determining the location of the tiles. Then, having made measurements of the tiles, transfer them to the wall area to be lined, marking the edges of the future finish with a simple pencil. After that, you should carefully remove the wallpaper only from these parts of the wall. Thus, it will be possible to combine two finishing materials. If you plan to cover the entire wall with finishing material, the wallpaper must be completely removed. In addition, old, peeling plaster is cleaned from the walls, as well as oil paint, if it has been previously applied.
	The next step is to prime the cleaned surfaces with a solution that includes antiseptic substances. The primer will help protect the walls from mold and other negative manifestations, and will also create high adhesion for the next finishing layers.
	If you plan to combine masonry with a painted wall, then its surface must be well puttied. Moreover, this work must be done as efficiently as possible so that there are no stains from the spatula and so-called sinks on the surface. It should be noted that this process requires some skill, therefore, if there is no experience in such work, then it is better to entrust the alignment of the walls to an experienced plasterer.
	Puttied and dried walls are carefully polished to smoothness with a construction grater, on which an abrasive mesh is first installed, and then fine-grained sandpaper. After grinding, the surface is again covered with a layer of primer applied with a roller with a fleecy nozzle. The water-based primer dries in about two hours.
	Next, the process of painting the wall follows. Usually, water-based or dispersion paints are used for this purpose, to which the color of the desired color is added. They are also applied by roller. This type of paint will not interfere with fixing stone tiles on top of it, but if you want to get even more confidence in the reliable fixation of the finishing material, then the wall should be marked and covered with its sections on which tiles are planned to be installed with a primer.
	While the paint or primer is drying, it is worthwhile to start selecting tiles. To do this, it is unpacked and laid out along the wall, which will be lined.
	Since the tile wild stone"has dark blotches, which are located differently on different specimens, you must try to decompose the fragments in such a way that the areas painted in more dark color, were evenly distributed in the masonry. It is easier to finish if the entire wall is masonry, but if it is located in separate sections, usually these are the areas around doorways and corners, then work must begin with them, from the floor plinth. However, before installing the first row, it would be useful to check the horizontalness of the plinth using the building level.
	If it turns out that it is not ideal, then you should measure the height of the tile and beat off the line along the upper side of the future row with a masking cord. It is on it that the first row of masonry will be displayed. At the same time, from below under the tiles in some places, you may have to make temporary linings from plastic plates or wooden slats. If the plinth has not yet been installed, then it is recommended to mark out the level, install and fix the support rail or starting profile, on which the first row of tiles will be mounted.
	Some tiles made of gypsum may have irregularities on their edges that form during casting - these flaws must be cleaned, otherwise they will interfere with the smooth fixing of the elements to the wall. To do this, use a sharp knife and sandpaper with a large grain, fixed on a piece of timber, or an abrasive bar.
	If there is a corridor outer corner, which will be decorated with an artificial stone, then work should begin with it, and it is best to use special corner elements for this. Before fixing the corner tiles with glue, it is recommended that they first be carefully tried on.
	Next, according to the instructions on the package, the tile adhesive is kneaded. Moreover, if the tile is made of gypsum, then the adhesive composition should also be chosen on a gypsum basis, and if the facing material is made of cement-sand mortar, then the glue is used on a cement basis. At the same time, to simplify the work, especially when installing tiles on a wall painted in light shades, it is better to choose tile adhesive in white.
	Some craftsmen prefer to fix the elements of this cladding with liquid nails, and this can be done under certain conditions. For example, if the tile is gypsum and has a small thickness and weight, and the room in which it will be installed has normal humidity. However, in any case, professionals recommend using tile adhesive, since it is cheaper, and such a composition, if it is of high quality, will more reliably fix the tile on the wall.
	At installation work oh, the tile will definitely have to be cut. Gypsum tiles are easy to use with an ordinary hacksaw, while for cement tiles you will have to use a grinder with a stone disk.
	If it is planned to produce “torn” masonry, and the tile has smooth edges, then it will have to be broken. To get a long protruding element, the tile is first filed, and then the extra parts are broken out by grabbing them with pliers.
	To obtain an arbitrarily uneven edge, it is simply broken off with the same tool. However, it should be noted that these manipulations can only be performed with thin gypsum tiles.
	So, masonry starts from a corner or doorway. The glue is applied to the surface of the wall and the tile itself in a thin layer, since when they are bonded, it should only slightly protrude along the edges. Moreover, this excess must be immediately removed with a spatula.
	The tile is applied to the wall and pressed well, glue is removed from its edges, and then it is tapped to the wall with a rubber mallet. The installation of the second and all subsequent rows is carried out according to the principle of brickwork, that is, the vertical seams must be displaced by at least ⅓ of the length of the tile.
	Each of the stacked rows is verified according to building level, since the tile can go skewed by just a few millimeters, which will gradually grow into centimeters, and the work will eventually be ruined.
	Another nuance that often causes inconvenience if ordinary tiles are used to decorate the corner, and not corner elements, is the mismatch of their edges, since it is often quite difficult to find perfectly right corners in apartments.
	Therefore, before applying the adhesive mass to the surface, it is necessary to try on two tiles to the corner, and if they do not match, mark and then cut off the protruding excess part. Since this version of the finishing material has a certain volume, the masonry from it will perfectly hide the small irregularities of the corner.
	Another difficult design area is the arch. But if gypsum material is used for decoration, then this problem is solved quite easily, again due to the ease of processing such tiles.
	Since the arch can have a different radius of curvature, which is difficult to calculate in advance, it is easiest to cut the tiles down at the place of its laying. To do this, the tile is applied to the place where it will later be fixed with glue, and the edge of the arch is outlined on it with a pencil. According to this mark, a cut is made with a hacksaw with fine teeth. In order not to be mistaken with the place where the element is fixed, it is best to circle it additionally on the wall by lightly pressing the pencil.
	Since the gypsum tile does not have flexibility, it will be difficult to fix it on the arch opening area. The gap that forms between the wall and the tile must be completely filled with adhesive mass. If “liquid nails” are used for fixing, then the glue is applied to the upper and lower parts of the tile, and after it dries, only the side clearance is filled with it. Thus, the entire arch is framed.
	Further, after the glue dries, in order to mask the corner joints of the masonry, a paint composition should be sprayed onto it. For this purpose, a conventional spray gun is suitable. If this device is not available, then you can cover the stones with a liquid paint solution using a soft brush. In any case, it is necessary to ensure that there are no streaks on the surface, therefore it is recommended to have a sponge on hand, with which they must be removed immediately.
	The end edges of the stone are carefully painted over with a narrow soft brush designed for watercolor work. The work must be carried out carefully, trying not to touch the surface of the wall.
	If part of the paint nevertheless got on the surface of the wall, it must be removed with a damp sponge, and if necessary, touch up certain areas of the surface.
	When the paint is completely dry, the masonry is covered with a water-based varnish. It has no unpleasant odor and dries quickly enough. The varnish is applied with a wide soft brush, since the composition should cover all recessed areas of the masonry. It is best to choose a matte varnish for the coating, as the gloss can spoil the whole look, because the "stone" will look unnatural.

Imitation of masonry in papier-mâché technique

Another option for decorating the walls of the hallway and corridor can be a finish that will not bring high costs, but will require a lot of patience and strength, as well as creativity. In this case, the cladding is done using the familiar papier-mâché technique. In the example brought to your attention, the master designed not only the hallway and kitchen, but also his office.

Next, it will be considered how to make material for manufacturing, how to apply it to the walls, and also paint it in the desired shades. Moreover, it should be noted that the shape of the stones in imitation of masonry can be for every taste of the master, and the color scheme is also selected for the intended style of the interior.

The shape and color of future “stones” are all the prerogative of the creative master

Step-by-step instructions for self-performing such a finish are in the table below:

Illustration	Brief description of the operation to be performed
	In order to perform lining in this technique, you will need ordinary paper egg trays, CMC wallpaper glue, a mosquito net measuring 1000 × 1000 mm or a mesh bag with small cells, designed, for example, for storing onions. In addition, it is necessary to prepare washing powder for hand washing, as it gives more foam, white and colored enamel paint, soft brushes 150 and 10 mm wide (you will need several of them), an electric drill with a mixer nozzle, a plastic basin and a bucket . In this case, the manufacture of a paper-glue mixture from ten egg trays will be demonstrated. This amount should be enough to cover an area on the wall with a size of approximately 550 × 550 mm.
	The production of the working mass is best done in the bathroom, as the work requires a large amount of water. In order not to clog the drain in the bath, it is best to protect it with a regular mesh, which is installed in the sink in the kitchen. Trays are treated differently: some masters knead them or cut them into small pieces, others simply immerse them in very hot water.
	So, for soaking ten trays, 6 ÷ 7 liters will be required. hot water, to which 50 grams of washing powder should be added. The trays are immersed in boiling water one by one, so that their cells do not overlap, and left to soak for half an hour. Then, taking a drill with a mixer attachment, mix and knead the resulting mass with its help.
	Further, the soaked paper is kept in water for at least two more hours, since the mixture should turn out to be almost homogeneous, and also without odors characteristic of tray cardboard. Washing powder will not only remove unpleasant odors, but will also contribute to faster and better paper softening. Two hours later, the mass is crushed and mixed with a mixer installed in an electric drill. Simultaneously with mixing, a kind of “washing” of the resulting mass is also carried out.
	Next, the resulting "porridge" of paper must be rinsed. To do this, a cut is installed in a plastic bucket mosquito net. It must be well laid out at the bottom of the bucket, and then fasten its edges to the bucket with ordinary clothespins. Then, about 1 kg of paper pulp is laid out in the container prepared in this way.
	After that, the mesh rises up and twists in the upper part, then the resulting "bag" is taken out of the bucket, placed on a lattice stand in the bath. Further, a mug is pressed onto the grid with the working mass, squeezing out excess liquid from it. The pressed mass, without freeing it from the grid, must be washed from the powder with running water from the soul. The mass must be turned over and squeezed by hand until clean water flows from it. Rinsing is carried out first with cold, and then warm water, after which the mass is wrung out, like ordinary underwear.
	The rinsed and wrung out paper is poured into a clean container, as it should be dry and crumble easily.
	The same work can be done using a mechanical washing machine, in which the centrifuge is installed separately from the washing tank. A mesh bag is installed in the centrifuge, paper soaked in soapy water is placed in it, then the bag is twisted and tied at the top. Then the centrifuge lid is closed, the device is turned on, and the mass is squeezed out.
	After spinning, the mixture is rinsed. To do this, water from the shower is poured into the centrifuge, and then moisture is again squeezed out of the mass. If an automatic machine is installed in the apartment, then it’s not worth the risk, since it has a different spinning principle, and the paper can clog the filters of the device. Therefore, it is best to do the work manually.
	The next step is to add one liter of diluted CMC glue to the pulp made from ten trays. When mixing, you will have to add a little more pure water to the mixture, and if the mass is not plastic enough, then also about 0.5 liters of glue.
	It is most convenient to mix the paper-glue mixture with the help of a mixer nozzle installed in an electric drill.
	As a result of mixing, a homogeneous, plastic, pleasant-to-work mixture with high adhesion to any surface should be obtained.
	Cladding work begins from the top of the wall from the ceiling. The mass is thrown and leveled on ceiling plinth or the junction of wall and ceiling. In this area, the mass should adhere tightly to the surface - it is pressed with fingers, at the same time forming the first seam between the "stones". The advantage of this finishing material is that the paper-adhesive mass, unlike other solutions, does not leave marks on any material located next to the surface to be coated.
	In this case, an example of the formation of a relief from a mass made from 10 trays is presented. The mass is applied to the wall by sketching or simply by applying the collected lump by hand with the necessary effort.
	Having sketched a small amount of material, it is pressed against the surface of the wall with the palm of your hand. The mixture does not leave dirty marks on the hands and easily adheres to any wall covering - it can be tile, wood, whitewash, concrete, drywall, brickwork and other materials.
	After the mass has been applied to the wall, it is pressed firmly against the surface with the hands, while creating approximately the same layer thickness. The facing material does not require ideal leveling, since natural stones almost always have an uneven surface, except for pebbles polished with water.
	On a leveled wet layer, the formation of a “stonework” relief begins. To do this, recesses are made in the mass with hands, which will become the seams between the imitated "stones". At the same time, the shape of the "stones" themselves is created.
	The master recommends, when creating a relief, to alternate small and large "stones", giving them various shapes. They should not be laid correctly, with even seams between them, it is better if the artificial stones created in this technique are randomly located.
	When forming the “masonry” elements, when pressing the mass with a hand, for example, when creating a seam, the mixture on the other side rises, forming a tubercle. It must be pressed, while distributing it to the mass located nearby. The mass in the seam between the "stones" must be well pressed against the wall, and in order not to use additional tools, the width of the seam can be determined by the thickness of the finger with which it is formed.
	When forming "stones", it is necessary to ensure that their middle part is not strongly pressed inward, that is, their edges should be below the middle. Otherwise, after drying, the “stones” will become like saucers, and this circumstance will surely give out their artificial origin, and the masonry itself will not look very aesthetically pleasing. In addition, do not leave the edges of the stones sharp, which can also ruin appearance relief - they are gently smoothed, leading to the seam.
	It must also always be remembered that if large and small “stones” are included in the manufacture of a three-dimensional pattern on the wall, then the paper-glue mass will be spent rationally, economically, which will allow one batch to decorate a larger wall area.
	The relief of the “stones” can protrude to different heights from the wall - this will give the masonry more naturalness, that is, they do not need to be especially compared and smoothed. If the design of the wall is planned with artificial stones imitating pebbles, then a little more glue should be added to the mass. It will make the material more plastic and easy to smooth.
	When the work on creating the relief is completed, the wall lined with this technique must be properly dried, otherwise cracks may form on it, or the layer will separate from the surface. To prevent this from happening, drying should be carried out in natural conditions, that is, there should not be a draft in the room or turned on heaters aimed at finishing. If at the end of the work there is an excess paper-glue mass left, it must be stored in an open form, otherwise it will acquire an unpleasant musty smell. If, nevertheless, this happened, then the mass will have to be stretched again, squeezed out and then can be used again in work. If moisture has evaporated from the mixture, then before use, water should be added to it, soaked and mixed well.
	When the created relief on the wall is completely dry, it is necessary to check it for cracks and flaking. If cracks are found, they should be repaired with the same paper-glue mixture, and while it dries, you can do color markings. In this case, the master first determines the color of each of the “stones” with colored dots.
	This method simplifies the work, since paint of the same color is first taken and it is applied to the marked “stones” throughout the entire facing layer. For coloring, it is best to use alkyd matte enamel or oil paint, which is applied to the "stones" in two layers.
	Then stones of a different color are painted, and so on until the entire surface is covered with a layer of paint. The paint is applied to the entire relief of the "stone" to the seam.
	Sometimes, to give naturalness to painting one “stone”, several shades are used, which gives the masonry elements a deeper volume. As for staining, we can say that this process can be done in different ways, depending on the goal and the style solution of the interior. It all depends on the artistic taste of the master.
	The paint is applied to the seam in such a way that it does not find the “stone” on the protruding relief. It should not stand out in the foreground, since the task of designing the seams is to give the finish neatness, that is, they should only be the background for the main elements.
	In this case, the result of work is presented in the selected green-brown-beige range, with seams made in blue shades. However, each master chooses his own color option, which is more suitable for his vision of the created interior.
	Properly lined wall, covered with enamel or oil paint, easy to clean with soapy water and a stiff brush. Based on this, we can conclude that the finish is moisture resistant and can be used for any of the rooms, including the bathroom. An exception is the area where the bathtub meets the wall - it is recommended to lay one horizontal row there. ceramic tiles, harmonizing in color with the future "masonry". It can also be noted that the mass made from cardboard of egg trays has low heat and sound conductivity, so a wall finished with this material will dampen noise from the outside, and will also become warmer, unlike brick or concrete.

So, available ways and necessary materials for finishing the corridor - quite a lot. The main thing is to start for yourself to decide what you would like to get as a result of the repair. The second step is to determine the amount that it is possible to allocate for repairs in this room, and then look for options that are suitable in all respects.

And in order to spur the imagination of an interested reader, below is a video that presents a lot of very interesting options decoration of the corridor and hallway.

Video: a variety of design solutions for finishing the corridor and hallway

Date: 07/25/2016

Repair of the hallway of a small apartment, in the photo examples successful arrangement, it is worth starting with the layout of the space. Due to limited square meters, experts recommend increasing the useful footage due to unused niches, adjacent rooms. This will allow you to push the walls of the corridor for the convenience of residents. Is it possible to take this advice as a rule if the bedroom or living room allows you to take the space or there are premises “for household needs”. Due to everyday realities, there are no such opportunities, but you can do otherwise - leave the partitions alone, expanding the space with the help of visual effects.

Bright small hallway

What can a small hallway

The functional load of the corridor cannot be compared with its area. The entrance hall is not only an “intermediate room” “from the living room to the kitchen”, but also a place where they undress when they come home from the street, hang jackets or coats, store outerwear and shoes, keys, umbrellas, mail, shoe care products …. And what is even more important - they meet and see off guests. Therefore, the room should be not only functional, but aesthetic.

In a small hallway, you need to take care of a functional set for outerwear, shoes and small things.

Advice:For the improvement of the hallway, you need to use all the possibilities, using the space to the maximum.

So, designers advise choosing cabinets up to the ceiling, and swing doors replace with an arch or sliding structure. If in the arrangement of the corridor, the advice of designers and custom-made furniture are priority, then the repair of the space is the work of the home owners themselves.

For a small hallway, a narrow wardrobe can save space.

Attention:For narrow hallways, you can make a small podium at the entrance. This solution will successfully delimit the space.

Hallway design in a small apartment

Narrow hallway with high ceilings

To give such an environment a “mundane” look, you need to use options with a multi-level plaster ceiling in repairs or paint the surface with a darker paint than the walls. Gloss gives depth, so it is better to give preference to a calm matte paint. Wallpaper with a vertical pattern is contraindicated for rooms that "sin" with the height of the ceilings. It is better to paste over the hallway with wallpaper with a horizontal ornament, which will reduce the height and add volume to the corridor. You can not use the "effect of unity" in the repair - when the wallpaper is pasted right up to the ceiling without a ceiling plinth.

A multi-level plasterboard ceiling will help to make a room a tall and narrow corridor more mundane.

Black stretch ceiling in the hallway will add depth to the room

To slightly visually expand the space of a narrow corridor, they often use horizontal striped wallpaper or a horizontal print.

low ceilings

If you got an apartment with low ceilings, then it is better to paint the surface in cold shades of white. You should not get carried away with fashionable innovations, such as a stretch or plaster ceiling, as the design "eats" at least ten centimeters.
The walls will thank you if you choose wallpaper with a vertical pattern, and only in light colors.

Low ceiling in the hallway of a small apartment

1. To visually enlarge the space, you can paint or paste over the room. light wallpaper- beige, blue, light green, pink.
2. Drawing on the wallpaper should not be voluminous! Minor patterns, small flowers or a monochromatic coating will not stand out and catch the eye.
3. Thresholds can be dismantled so that the floor looks like a single structure without borders.
4. For the role of flooring, it is recommended to choose linoleum or tile. Laminate and parquet should not be exposed to high humidity.
5. Wall panels, artificial stone and other design delights do not fit a small corridor, as they hide space due to the frame.

Visually increase the space of the corridor will help finish the walls and ceiling in bright colors

For a small hallway, you should choose wallpaper with a small print.

Advice:Shades of paint and wallpaper to be matte.

The market of finishing materials offers ample opportunities for creative individuals. Innovations and developments do not leave indifferent even the most sophisticated buyer. But not all "novelties" are suitable for such a space as a corridor. And the point here is not only in an aesthetic sense - the operational component is much more important. It's no secret that the entrance hall is exposed to the most intensive loads. It is here that the most dirt accumulates, and the walls quickly lose their former aesthetics. Therefore, you need to choose a coating not only in appearance, but also in its characteristics.

An interesting option for a small hallway will be its design in the loft style, the brick coating is durable, and also has a predominantly horizontal pattern.

What should be the wall covering for the corridor:

• Washable;
• practical;
• durable;
• "Anti-vandal".

Attention:
The labels always indicate the type of wallpaper.

Glass fiber
They are one of the most reliable finishing materials on the market. The wallpaper is textured, imposing, stylish and unusual. They imply subsequent staining in the desired color. Paint is better to choose washable and resistant to physical impact - latex. Walls can be repeatedly repainted in different colors.

Glass fiber is often chosen to be painted in a suitable color later.

Glass fiber always has an interesting texture that can be well beaten

Wall-paper

Decorative plaster
You probably paid attention to the aesthetic and attractive facades of buildings, which are plastered in an interesting way, or rather, using the original “fur coat”, “bark beetle”, “lamb” plaster. But such a stylistic solution can also be used to repair the hallway. The advantages of the finishing material are undeniable: it is not exposed to ultraviolet radiation, has increased resistance to damage, can be repainted and is not washed off with water. If a house plastered in this way for decades does not lose its attractiveness, what can we say about an enclosed space! The only drawback of this coating is the impossibility of frequent color changes, since the texture pattern can be painted over. This is what is needed, because if the plaster withstands showers and hail for years, then in a dry place any wet cleaning will seem like a joke to it.

Mix for decorative plaster it is better to choose in light shades

Microcement
Budget option for decorative plaster. It is a polymer-cement mortar with dyes. Has the advantages of its counterpart, can be applied to different types old wall covering(be it tile or drywall), withstands many cycles of wet cleaning, commensurate with the strength of the stone.

Wall decoration of the corridor with microcement is great for loft style and minimalism

flexible stone
Belongs to the category of natural materials for finishing walls and facades of buildings. It has all the advantages of a mineral, unpretentious in maintenance. It looks original and is rarely found as a material for arranging corridors.

Decorative stone in a small hallway

Fake diamond
Cheaper equivalent natural stone. Distinctive feature- it is light weight (compared to eco-minerals). Easily evens out minor wall imperfections. Differs in high cost, as well as a natural stone.

In a small hallway, it is not necessary to trim the entire space with artificial stone to emphasize the accent, one wall will be enough

Cork wallpaper
Eco-friendly wall covering that does not emit in environment toxins. Suitable for furnishing large hallways because it "eats" a lot of light. Not very scratch resistant, but minor damage is barely visible.

Small damages are not visible on the cork wallpaper in the hallway

Quartz wallpaper
A new generation of moisture and cleaning resistant wallpapers. Models are a paper or non-woven base, on which a layer of sand is applied. Can be in the form of frescoes, painted in desired color. This is one of the most reliable and stable wallpapers that are not afraid of the claws of pets. This coating can be washed with a stiff brush.

Beautiful wallpaper in the hallway

Metallic wallpaper
This type of finishing materials is nothing more than a base + foil layer. Wallpaper perfectly reflect light and any electromagnetic radiation. Reliable enough, often have a varied texture.

Attention:
You can stick this type of wallpaper only on a completely flat surface.

Metallic wallpaper has a beautiful sheen

Liquid wallpaper
They are a dry cellulose mixture, which is diluted with water and applied to the walls with a spatula. In the future, the surface can be painted. Advantage - no need to pre-align the walls.

Liquid wallpaper is great for uneven hallway walls

Ceramic tile
All the advantages of ceramic tiles are known to the domestic consumer to the smallest detail. The downside to using a corridor cover is an unaesthetic appearance, which behind the scenes resembles a bathroom or a bathroom.

Ceramic tile

What is not suitable for a small hallway

When choosing certain finishing materials, many of which have perfect performance characteristics, it is worth remembering that the installation of drywall, PVC panels is not the most deliberate solution, since such a design requires a frame. The frame hides up to 20 cm of usable area.

Sliding wardrobes for a small hallway are better to choose with a mirror surface of the doors, this will visually increase the space

Vases and pots with indoor flowers are inappropriate for the corridor. BUT corner hallways must be equipped with appropriate furniture - corner cabinet. Don't forget about lighting! Lighting should be bright. The chandelier can be located in the center of the corridor. Optimum options for point, directional light with a light intensity regulator. Furniture and walls of a conflicting color will leave nothing but hostility behind them. Even the most expensive porcelain tiles will turn the corridor into an operating block.

For lighting in a small corridor, it is better to use Spotlights they don't take up much space

Competent repair of the hallway in the apartment: photo small corridors

Nice doesn't always mean right. This concerns, first of all, the repair of such a problematic place as a narrow or small hallway. Often the user is "led" by emotions, preferring stylish wallpaper with large floral print. In practice - small space the hallway will seem even smaller. In order not to make a mistake with the choice of finishing materials, you need to seek help from designers. They will create an author's project for the arrangement and repair of the corridor and suggest what better materials use in decoration.

Design ideas should be combined with the size and space of the room.

modern hallway design

Repair of the hallway in the apartment 40 photo ideas:

The corridor or hallway is the room where the tenants of the apartment first of all get when they come home from the street, so pollution and damage are sure to appear on their walls over time. If there are small children or animals in the apartment or house, then the decoration of the lower part of the wall will certainly be in a special risk zone. Therefore, when starting repairs, you need to carefully consider how to finish the walls in the corridor so that the material is resistant to most mechanical influences.

In addition, it is necessary to take into account the fact that the entrance hall is usually the “face” of the apartment, setting the tone for the interior design of all rooms, which means that one cannot but think not only about the strength qualities of the material, but also about its aesthetic side.

A large assortment modern materials, which today can be found in hardware stores, makes it possible to choose a finish for any request in terms of style and financial possibilities. However, before dwelling on one of the many design options, you need to consider the positive and negative aspects of the chosen approach.

wood finish

The tree has not gone out of fashion for many centuries, thanks to its amazing qualities that create the most favorable microclimate in the premises of the apartment. For finishing the hallway and corridors, wooden facing materials, produced in the form of lining or panels, depending on the chosen design style.

Natural lining

Wooden lining is a more affordable material compared to natural panels. It is made in various forms, so it is possible to use it to create an interior that matches different styles.

Several types of lining are produced, but all of them are used when decorating a corridor in such styles as Provence, Country or Russian hut.

Wood is a material with a structure that does not conduct heat well, thereby keeping it indoors, so walls sheathed with it will always be warm to the touch. In addition, such a finish can partially reduce the level of noise coming from outside.

Wooden lining is often called a tongue-and-groove board in a different way, although this is a contradiction - such a term is more suitable for floor boards that do not have an external relief. However, a board with a smooth, non-profiled outer surface is often a good material for finishing walls in hallways and corridors.

The lining is classified, in addition to the type of profile, according to quality features - it is customary to distinguish between classes "extra", "A", "B", "C".

• "Extra" is the lining of the highest class, without defects and the core of the trunk.
• "A" - a class of material, also of high quality. In the production of this lining, wood is selected, on which one knot per 1500 linear millimeters is allowed on the front side or edge, as well as up to two non-through and small cracks on the back side of the board.
• "B" - a class of lining, which has a lower quality, so it can have up to four knots for every 1500 p. mm, with a diameter of up to 20 mm. It is also allowed up to two non-through cracks, darkening and streaks.
• "C" is the lowest class of finishing material. It can have knots up to 25 mm in diameter, several cracks up to 5% of the length of the lamella, bluish and dark stains, and even mechanical damage. This material has a low price, so it is often used for the manufacture of crates. If such a lining is planned to be used for decorative cladding, then it will have to work a lot on it, cleaning the surfaces and repairing flaws.

Any of the classes is suitable for lining the walls of the corridor, but some of them can be used in their natural form, that is, while preserving the textured pattern of the tree, while others must be painted to mask the damage repaired with putty.

The lining is made from various woods, both coniferous and hardwood. The most affordable material can be called pine, linden and aspen, and the most expensive finish is lining made of larch, cedar, oak, alder and ash.

The lining can be installed on the walls horizontally or vertically, depending on the effect you want to get. If the hallway or corridor is narrow and long, then it is best to mount the lamellas vertically, otherwise the room will seem even narrower and longer. In a square hallway, the lining can be fixed in different ways, as planned design decoration. To give the room originality, you can use a combined mounting option, that is, sheathe one wall horizontally, the other vertically, or even combine different directions on one wall.

Natural massive panels

More expensive natural wood finishes are massive panels, which can completely sheathe all the walls, one of them, or only the lower sections are decorated with them. For the manufacture of this material, mainly expensive hardwood is used, which has a beautiful textured pattern, such as beech, oak, alder, cedar, ash. However, all these breeds have a high price and are not always affordable for a family with an average income. To reduce the cost of their production, most often different types of wood are combined with each other.

For example, the base of the panel is made from a less expensive material - it can be pine or spruce, and then its front side is covered with two or three layers of fine wood veneer. The veneer is fastened to the base special technology hot pressing, which gives the panels increased strength.

Panels are also made from plywood, which is also veneered, and then varnished or waxed.

Wall panels, depending on their design, can be applied in different styles- these are classics, classic English, Victorian, modern, neoclassicism, rococo and other trends.

Advantages and disadvantages of wood finishes

If we talk about the negative aspects of finishing the corridor with wood, then they practically do not exist, since it is devoid of flaws, with the exception of the high price of some of its options. But on the other hand, it has many more advantages than any other material.

• Wood has excellent strength and resistance to mechanical stress, therefore, with proper processing, the finish is not afraid of the claws and teeth of pets.
• The environmental friendliness of wood is undeniable compared to others faux finishes, so this design is able to create a favorable microclimate for the residents of the apartment.
• Durability wooden finish will allow not a single ten years to resort to repairing the hallway.
• If you want to change the interior design of the room, the finish can be easily painted in one or more colors.
• Ease of installation of any type of wood finish, if available necessary tools, allows you to carry out this process on your own.
• Each type of wood has its own textured pattern and color scheme, so choosing the option that will appeal to the owners of the apartment and fit well into the interior of the hallway is not difficult.
• Both wooden panels, and a well-fitted board, and lining go well with the most different materials, such as wallpaper or artificial stone, so this finish provides ample opportunities for imagination when developing an interior project.

Wallpaper finishing

Despite the large number of new finishing materials that have recently appeared in the public domain, they continue to be popular, not only for living rooms, but also for the corridor or hallway.

But, as you know, wallpaper is a rather thin material that is prone to damage and pollution. Therefore, if there is no perverse desire to renovate the corridor every year, then it is best to combine them with more durable finishes, such as wood, plastic, chipboard or MDF panels or artificial stone.

It is especially important to choose a combined option if there are animals in the house. Well, in the event that a small child lives in the apartment, and it is decided to finish with wallpaper only, then their washable version is best suited.

If earlier in stores you could only find paper wallpaper, then today the range of this finishing material is extremely wide. So, for a hallway or corridor, non-woven, vinyl, fiberglass, metallized and photo wallpapers can be suitable. You should not choose textile finishing cloths for decoration of these rooms, as dust can accumulate in them, which can cause the development of allergic reactions.

To make a choice, it is worth considering a little more in detail the most popular types of this material.

Non-woven wallpaper

The non-woven version of the wallpaper consists of two layers - a base made of non-woven cellulose fabric, as well as an upper polymer coating. This type of material is not strong enough, but is able to hide small flaws in the walls. It does not shrink when glued, wear-resistant, environmentally friendly, easy to install on your own, since when finishing, glue is applied only to the wall.

Non-woven wallpaper is suitable for decorating not only walls, but also the ceiling. If you need to change the interior, they can be painted in the desired color.

If a cat can reach the non-woven wallpaper, it will gladly sharpen its claws on them, so it is best to combine them with high, durable panels.

Vinyl wallpapers

Vinyl wallpapers also consist of two layers - a base made of paper or non-woven fabric, and a decorative coating of polyvinyl chloride, which can have different thicknesses and reliefs. This coating has many varieties, and one of them, which has become especially popular, is “silk-screen printing”.

Vinyl sheets have high strength and wear resistance, they are inert to ultraviolet radiation and retain their original color for many years. Such wallpapers can be called washable, as they are easily amenable to regular wet cleaning. The variety of colors and textures of this material is so great that they can be matched to any interior style.

If this particular finish is chosen to decorate the corridor, then it is not recommended to purchase wallpapers of dubious quality due to their low price, as they can be toxic. The best option for any of the rooms there will be non-woven fabrics, as they are "breathable".

fiberglass wallpaper

Wallpapers based on fiberglass have increased strength, as they contain strong fibers in their composition. This is an environmentally friendly material that can be painted after wall gluing with water-based or latex-based paints. Wallpapers are highly wear-resistant, their service life is about 30 years, and during this period they are able to freely withstand up to 15 repaints. The material does not crack at the corners when the structure shrinks, it does not burn, is water resistant and is not a nutrient medium for microflora colonies.

Wallpapering the corridor with wallpaper can be done independently

Many owners have already tried their hand at carrying out such a finish with their own hands. But if there is no relevant experience, then before starting this work, we recommend that you read the article on our portal.

Wall mural

Wall murals are made from various materials- they can be paper, non-woven, vinyl and fabric. For the corridor, it is best to choose a vinyl or non-woven version, as they have the characteristics suitable for this room.

Finishing material is also subdivided by texture. So, on sale you can find:

— Wallpaper with a smooth glossy and matte surface.

- Embossed wallpaper imitating sand, canvas and other fabric weaving, as well as a variety of three-dimensional drawings.

This finishing material can be decorated with images with different effects:

• Background photo wallpaper decorated with frequent floral or other patterns, arranged in a certain order. They differ in that they do not have a specific plot. Like option is suitable for decorating a corridor or hallway, but at the same time it is necessary to choose washable varieties or combine them with other materials.

Background decoration, depending on the choice of color and pattern, can visually expand or reduce the area of ​​​​the room being decorated.

• Panoramic wallpaper have images of natural or modern urban landscapes, balconies or small courtyards. They can also create a room-enlarging effect, so they are the best suited for decorating narrow rooms.

• Photo wallpaper with realistic images are also often used to decorate the walls of corridors - these are photographs of flowers, grass, flowering trees, etc. Most often, these canvases have a three-dimensional 3D effect that creates the illusion of expanding space, or HD, in which the drawings have the clearest detail.
• Subject photo wallpaper , on which large images of one or more objects are applied, are better suited for rooms with large areas, since in small rooms they will look ridiculous and visually reduce them. For a corridor, this is not the best option.

Have you tried wallpapering?

The question is not idle, since this finishing operation is quite complex, replete with nuances. in order to avoid mistakes and not spoil expensive material - read in a separate publication of our portal.

cork finish

Perfect suitable option finishing for the corridor will cork, which has antistatic properties, fire-resistant and non-hygroscopic, resistant to deformation, ultraviolet, and most importantly, to mechanical stress. Due to the strength of this material, it is not afraid of the claws and teeth of animals. Cork is an environmentally friendly material, it is very light in weight, which simplifies its installation on walls.

plastic panels

Cork is a natural material that perfectly insulates the room and makes the walls warm and pleasant to the touch. Cork finishing is produced in different options- it can be wallpaper, plates and rolled canvas on a self-adhesive basis. The color scheme of the finishing elements is diverse, as it can have a large number of options, both plain and interspersed with different shades.

Cork finishing materials are made from oak bark growing in the Mediterranean. Veneer is cut from the peeled bark, solid panels are prepared, or it is crushed into crumbs, followed by the production of wall and floor slabs, roll materials, baseless or paper-based wallpapers. Cork is used to decorate not only walls, but also other surfaces of the room.

In stores, you can find cork materials that require additional processing - they have a lower price. However, it is better to purchase a finish that does not need additional application. protective equipment, since by carrying out this process incorrectly, it is quite possible to spoil the appearance of the coating.

• Cork panels

Cork tiles or panels are made on a plywood or MDF basis, on which tongue-and-groove joints are made. This allows you to assemble individual elements into a single coating with almost invisible seams.

Another version of cork slabs consists of three rather thin layers - the lower one, which serves as the basis, the middle one, and the upper decorative one, interconnected with natural glue. This finishing material is decorated with cork veneer.

• Roll web

Rolled cork cloth consists of two layers - pressed crumb, which is the basis, and decorative thin veneer. Cloths are glued on the surface of the walls and floor butt. After installation of such a finish, the sheets merge into a single coating with invisible seams of joints.

In addition to decorative, technical cork roll coatings are produced, which are used as substrates for other types of finishes. They are used as an effective insulating and soundproofing material.

• Cork wallpaper

Cork wallpaper has a thickness of 1 to 4 mm. They can be baseless, like a roll web, or paper serves as the basis for them. Therefore, they are glued to prepared walls in much the same way as ordinary wallpapers, but, unlike them, they are able to mask small flaws on surfaces.

It should be noted that any cork material goes well with other finishes, so you can develop and implement various combined options.

Cork flooring is well suited for finishing walk-through rooms, both in terms of aesthetic and technical characteristics. The only thing that can stop you from choosing it is a rather high price.

Wall decoration with bamboo

Finishing the corridor with bamboo is great choice, as this material has high strength and is not afraid of mechanical influences. In addition, it is an environmentally friendly and durable, easy-care material that can be cleaned with a vacuum cleaner or a damp cloth.

Bamboo trim is produced in different forms - it can be rigid panels or wallpaper mats assembled from slats of different widths.

• bamboo panels

For the manufacture of bamboo panels, one-piece trunks or their halves are most often used, but sometimes they are also assembled from slats glued to the base. They consist of one or two layers, are produced by hot pressing, while they can have different dimensions and thicknesses.

Bamboo pairs well with other finishes such as wallpaper or tiles that mimic flat stone options. Most often, panels are used to decorate the lower part of the walls, which are more in need of their protective functions. Bamboo is not afraid of cat claws and any pollution - the latter are easily removed by all available means. On the wall, the panels are fixed with the help of “liquid nails”, and installation, as a rule, does not pose any difficulties.

• bamboo wallpaper

Bamboo wallpaper is made from slats, which bloom inner part whole stems. The thickness of the canvases can vary from 3 to 5 mm. The slats are stitched with a thick strong thread, which makes them look like mats (which, by and large, they are). Most often, rolls of 10 × 0.92 m are found on sale.

Another version of the wallpaper made of this material has a base of technical gauze or rice paper, on which slats cut from the outer smooth part of the trunk, which is its bark, are glued. The width of the slats is from 8 to 20 mm, and the thickness is 1÷2 mm. A roll of such wallpaper has standard parameters, its length is 10,000 mm, and its width is 2500, 2000, 1500 and 1000 mm.

Wallpapers are produced in different design options - they can be plain or have a natural pattern characteristic of this material.

a natural stone

In terms of their decorative qualities, bamboo wallpapers are practically not inferior to panels. They can be combined with each other, but for this you need to choose harmonizing shades.

Bamboo wallpapers are fixed to the wall with PVA polymer glue. It is recommended to level the walls with drywall before their installation, on the primed surface of which they are fixed quite easily. If the material will be glued to another, more complex surface, then it is better to use “liquid nails” for installation work.

Plastic panels

PVC panels are an affordable and easy-to-install material that can, nevertheless, significantly transform any room. Such cladding provides great opportunities in planning your own version of the interior of the corridor, as it is produced in a rich variety of colors, ornamental and relief patterns, with a very reliable imitation of natural materials - the texture of wood, stone, sand, etc.

This material is very popular due to its aesthetic appearance, durability and relative strength. The panels are easily put in order with the help of wet cleaning, so they are perfect for finishing the walls of the corridor, both the lower part of the wall and all surfaces completely.

If PVC panels are chosen for finishing the corridor, then the repair will take place quickly and relatively cleanly, without unpleasant odors paint and spilled glue.

With the help of this material, it is quite easy to level the surfaces of the premises, it becomes possible to hide cables and communication pipes without digging the walls. In addition, soundproofing material can be placed behind the panels.

Panels produced for interior decoration, are an environmentally friendly material that does not emit harmful fumes.

The advantage of PVC panels is also that such a coating will not attract animals to itself, as it has a smooth surface that is not easy to grab with claws.

In order for the finish to meet all the qualities mentioned above, you should not purchase cheap materials. The stiffening ribs installed inside the panel should not be visible through the outer solid layers of plastic, and when pressed with your fingers, they should not be crushed.

The surface of the panels should not have deformations and dents, and the joining of individual lamellas should be easy, with the tongue fully entering the groove.

It is impossible not to recall that for the decoration of corridors and hallways it is necessary to choose PVC panels with a flammability category G1 or NG. They have a special treatment that makes them more resistant to ignition and melting even when heated to extremely high temperatures. This circumstance must be taken into account so that in emergency situations the exit from the apartment is not blocked by strong and toxic smoke or even open fire.

The process of installing PVC cladding on walls is available to everyone!

Any more or less “savvy” with basic building skills, the owner is able to perform such a cladding. How it is produced - read in a separate publication of our portal.

MDF or fiberboard panels

MDF is a fibreboard obtained by dry pressing fibers using carbamide resins. The outer side of the panels is decorated with a coating that imitates natural wood of different species or other natural materials. Some panels are covered with a special protective film - this process is called lamination.

In addition to MDF, fiberboard panels are also on sale, which have a lower cost, but experienced craftsmen still recommend choosing the first finishing option.

The essential difference between these materials lies in their technical characteristics:

• MDF is a safer material than fiberboard, since the latter uses phenol-formaldehyde resins as a binder, which emit toxic fumes that can harm the health of apartment residents. MDF, from this point of view, is incomparably cleaner.
• The strength of MDF is much higher than that of fiberboard finishes. Such panels are more resistant to external mechanical influences, which is very important for a room such as a corridor.
• MDF, unlike fiberboard, has a water-repellent coating that allows for wet cleaning of walls without much regard for the frequency of this process.

However, for all its merits, MDF has a high flammability category - G4, and different models Fiberboard, this parameter can be lower - from G1 to G4. Therefore, when choosing a finish, you must definitely pay attention to this characteristic.

Installation of both MDF and fiberboard is carried out in the same way, approximately the same as for PVC panels and natural wooden lining: along the batten guides installed vertically or horizontally.

MDF panels are produced in different dimensional standards. Thickness usually varies from 6 to 14 mm, width - from 98 to 325 mm, and in length they are 1300 or 2600 mm, that is, they are perfect for filling floor-to-ceiling space in a standard city apartment.

MDF panels are produced in several variations, which are divided according to the production method, characteristics and color features. They may be:

• Whole-pressed.
• Laminated with a smooth glossy surface.
• Moisture resistant, designed for rooms with high humidity.
• Veneered, imitating the finish of natural wood or cork.
• Painted with a special paint that can smooth out irregularities and create a glossy or matte surface.

Fake diamond

An artificial decorative stone is becoming quite a popular material for finishing the corridor. They either completely lay out the walls, or combine it with plastered or otherwise decorated surfaces.

Gypsum and cement based stone

The most common, which is used for decoration, is made on the basis of cement or gypsum using various plasticizing additives. This finishing material can be characterized as follows:

• A wide variety of relief patterns and shades of artificial stone perfectly imitates a wide variety of natural materials.
• Sufficiently high strength indicators guarantee the durability of the finish with properly executed masonry.
• In case of accidental damage to the surface of the stone, they can be easily restored on their own, the main thing is to determine exactly what material it is made of. If the base is gypsum, then the restoration should be done only with this material (the same applies to cement).
• If you have experience in laying ceramic tiles, it will not be difficult to finish the walls with artificial stone yourself.
• Artificial stone also has several disadvantages:
• Low resistance to abrasion of the surface of the material. Therefore, it will be necessary to periodically update the color or immediately cover the surface of the stone fixed to the wall with a varnish with high surface resistance (for example, polyurethane).
• The cost of such a finishing material is quite high.

You can make artificial stone yourself!

If you want to save on the purchase of material and try your hand at this craft, the reader should read the article, which is located on the pages of our portal.

In addition to the above materials, more expensive ones are also used for manufacturing - they make a more durable artificial stone that is not subject to abrasion and mechanical damage.

acrylic stone

This kind of artificial stone is made from 75% mineral natural environmentally friendly materials that exude from white clay. In addition to it, it includes stone chips - it can be marble, granite, jasper and other minerals. The binder for the ingredients is acrylic resin (polymethyl methacryl). The color scheme is created by special natural pigments that are harmless to humans.

Thanks to all the above components, acrylic artificial stone is a very wear-resistant and durable material, so even elements such as kitchen countertops and sinks.

quartz stone

Quartz artificial stone is more durable than acrylic, as it contains about 90% natural crushed quartz. It is more resistant to scratches and any other damage, and is also used not only as a decorative finish, but also for the manufacture of durable kitchen countertops.

Polyester resins serve as a binder for quartz and color pigments - thanks to these components, the material is stronger than granite. In addition to strength, quartz stone has such qualities as environmental friendliness and resistance to the appearance and development of microorganisms harmful to humans on it. This material is light in weight and easy to care for, it does not absorb dirt, and it is enough to periodically wipe it with a damp cloth.

Indoor walls, from a technical point of view, have no restrictions, since it is not combustible and does not contain substances harmful to humans. However, it is necessary to show a sense of proportion, otherwise the apartment will resemble some kind of cave. Therefore, most often stone trim is combined with decorative or ordinary plaster, and sometimes even just with wallpaper.

The stone is most often laid around doorways, or the corners of the room are trimmed with it, which will contribute not only to the decorative design, but also to the protection of the most vulnerable places on the walls to damage.

Single inserts of stone on the plastered surface of the walls are also possible. The main thing is to think carefully color scheme and the correct location of the finishing material.

Now, after getting acquainted with what finishes are best suited for the walls of the corridor, it will be easier for the reader to choose the best option, given the quality of the materials, the design style and, of course, their own financial capabilities. And let the video selection below with very interesting design solutions for decorating the corridor in the apartment be of help to him.

Video: There is a lot to learn - design options for finishing the corridor