Finishing material plastic. Decorative wall cladding with plastic - interesting ideas for interior design. Plastic as a material
Redevelopment of premises, their zoning are quite often implemented methods that allow you to increase comfort on the same “squares”. A drywall partition with a door is the most common home renovation option. If you delve into the nuances of such work, then it is quite possible to do without outside help, especially the services of a professional.
Preparatory stage
Drafting
Development of a partition scheme. There are some points to be taken into account here. Since not just a plasterboard partition is being arranged, but with a doorway, you need to choose a place for it in the “new” wall. In this regard, one should proceed from the specifics of the further use of adjacent premises, their filling household appliances, furniture and so on.
Is it supposed to mount something on the cladding of the GKL. The sheets themselves do not differ in strength; they acquire it only with additional amplification. And if it’s just not possible to attach a shelf, a lamp, hang a massive picture or something similar to a plasterboard wall, then it is necessary to provide for installation in the crate of load-bearing elements. The practice of building partitions from GKL shows that the installation of single vertical racks from profiles is impractical for a number of reasons. One of them - a relatively thin metal "plays" with strong pressure on it.
A simple solution is to install a second, additional guide. If a significant strengthening of the structure is necessary, it is advisable to place wooden blocks (thick slats) in the required places.
If the partition scheme is drawn up correctly, it is not difficult to find these elements after sheathing the frame. Alternatively, leave marks on the floor with a pencil or felt-tip pen.
When planning the manufacture of a plasterboard partition, it is worth immediately determining which door it will be with - swing or sliding. In the latter case, when calculating the insulating material, the volume of its purchase is significantly reduced. And if the opening is significant, and the width of the room is small, then the cavities between the GKL are generally left unfilled; otherwise, the sashes simply will not part.
Vertical racks require reinforcement. And therefore, jumpers from the PN profile are installed between them. The scheme of their location is developed independently.
Taking measurements
The dimensions of the room at the location of the partition are determined. It must be understood that floor slabs do not lie in a strictly horizontal plane. Therefore, the height should be measured at opposite walls. What for? If its difference is significant, then you will have to think about how to level this disadvantage. The prospect of cutting a sheet of drywall at an angle, besides cutting off a small fragment from it, is not the best. Most likely, 1 - 2 samples will be hopelessly damaged.
The distances from the walls to the vertical posts that form the doorway are measured. This is necessary to calculate the required length of the lower guide profiles, since the threshold is not made. Therefore, two PN rails will have to be attached to the floor (before the passage).
Calculations
The partition from the GKL is done on its own, including, for the reason reasonable economy paying for third party services. The same applies to the purchase of materials. Some reserve is needed, but the surplus in in large numbers Not needed; the prospect of early use is illusory, which means a waste of money.
You should not immediately buy drywall sheets and profiles at the first outlet that comes across. Although they are standard dimensions, not all manufacturers strictly adhere to standard sizes. The task is to select samples in such a way that there is as little cutting as possible. This will facilitate the work and save on waste optimization.
On the other hand, in some areas it will be necessary to mount small fragments of plasterboard, put jumpers (to strengthen the frame) from profiles. Therefore, materials should be selected according to linear parameters with the expectation that after cutting them, finished “details” are obtained.
The connection of drywall sheets is done on vertical racks. The recommended interval between them is within 55 ± 5 cm. If the GKL are overall, then one additional rack is mounted approximately in the middle to prevent punching through the wall.
Selection of materials
Guides
Without installing a supporting frame, it will not work to make a plasterboard partition, especially with a door. For all its advantages, GKL has a number of disadvantages, one of which is the fragility of the sheets. Therefore, during the installation process, they must be fixed on a solid base.
When arranging partitions, two types of profiles are used. What is the difference?
- UW (or PN, in Russian markings). The last letter in the abbreviation "suggests" that these metal rails are used as guides. That is, they form the outer contour of the crate. Therefore, they are mounted on the floor, ceiling, and walls, but only if they are load-bearing.
- CW (PS). These profiles provide the necessary "rigidity" of the structure and are installed vertically, according to the developed mounting scheme. They are called rack-mount (this is indicated by the letter C).
- PU - corner profile. It is used to strengthen (strengthen) joints.
Advice. When choosing rails in width (and it can be from 50 to 100 mm), you should take into account the dimensions of the room, and hence the linear parameters of the partition from the hl. The more spacious the room, the higher the ceilings, the more massive the profile needs to be fixed, constructing the frame.
Drywall
Its sheets are produced in a large assortment, and each type of product has certain characteristics. When choosing a GCR, you need to take into account the specifics of the room and the layout of the partition. For example, if it is mounted in a room with high humidity, then drywall is used in the “moisture resistant” category (GKLV). It is also worth taking into account whether it is necessary to bend the sheets during the work; based on this, the thickness of the facing material is selected.
Insulator
You can make a plasterboard partition only inside the building. Accordingly, from one room it turns out two. The choice of insulating material depends on how it is planned to use the "new" premises. In other words, what its properties should be in priority. If the main criterion is to reduce heat loss, then it is optimal to insulate with mineral wool. If it is necessary to improve such a characteristic of the interior structure as sound insulation, it is better to purchase polystyrene foam. Or sheet, roll products based on cork, but they are somewhat more expensive.
Additionally
- Dowel-nails.
- Self-tapping screws (for metal).
- Screws for fastening GKL (commercially available).
- Damper tape. It is placed under the guide profiles to isolate them from the base and compensate for thermal deformation.
- Sickle tape.
- Primer + putty for drywall.
Instruments
- Scissors (for metal) - for cutting profiles.
- Construction knife - for cutting plasterboard.
- Plumb and level.
- Perforator.
- Screwdriver.
This is the main thing you need. Other accessories, if required, can be found in any home.
The procedure for erecting a partition
markup
- Determining the line of attachment of the lower guide (this is easy to do with the help of a "chopping" cord).
- Projecting it onto the ceiling and walls (to help - a rail, a building or laser level, a plumb line).
- Marking the floor at the location of the opening. If the door is hinged, then about 25 cm must be added to the width of the block.
Lathing construction
- Cutting PN-profiles.
- Sticker on their sides adjacent to the surfaces, damper tape.
- Mounting guides. It is recommended to first fix the top rail on the ceiling. This will allow using the plumb line to check the symmetry of the line below.
- Installation of wall (vertical) racks.
- Opening formation. Already noted - either double profiles, or single + wooden slats. For hinged doors you can use a square tube with an appropriate diagonal. There are several options for strengthening the structure, and it is advisable to study this issue in advance.
- Fastening of PS-profiles along the entire width of the partition, in accordance with the diagram.
- Installation of jumpers and embedded bars. To the latter it will be possible to attach wall cabinets and the like.
- Laying electric / wiring, internet - everything that is provided.
Frame cladding
- Finishing GKL battens on one side, leaving a gap between them and surfaces of the order of 5 mm. When tightening self-tapping screws, their hats must be recessed into chamfers.
- Laying the insulation material.
- Facing the second side of the frame.
- Reinforcement of the partition with corner profiles.
Block installation
It is necessary to check that the frame does not protrude beyond the plane of the wall. After fixing the door, the gaps are closed mounting foam.
Exterior finish
- Puttying the joints of the plasterboard and the locations of the caps of the hardware.
- Their reinforcement with sickle tape.
- Soil treatment.
- Surface grinding as a stage of preparation for finishing.
There are many ways to independently decorate a plasterboard partition - painting, pasting with wallpaper or decorative film, applying textured plaster. GKL are popular in the construction industry due to the ease of working with them and the variety of surface design options. If the meaning of all technological operations is clear, then the services of a master are not needed to build such a partition.
There are two options for placing the door, depending on the requirements for its position. If the location of the doorway is strictly defined, the structure is “tied” to it and adjusted so that the drywall joints do not fall on the door pillars (Fig. 1, a).
In the case when the position of the opening can be varied, it can be "embedded" in the structure, that is, made where there are no joints (Fig. 1, b). It is better to arrange the opening so that there are two structural posts on both sides of the profiles framing the doorway. They can be connected to several door lintels, which further strengthens the door block.
Attach door frames to the vertical stud profile of the partition frame without installation additional elements rigidity is possible under the following conditions: the height of the partition does not exceed 2600 mm; width door leaf- no more than 900 mm; the weight of the door leaf - does not exceed 25 kg.
The rigidity of the partition with the doorway in this case will be ensured by a reliable connection of the rack and guide profiles, which, in turn, must be fixed to the ceiling with dowels at a distance of no more than 100 mm from the opening. Above the doorway, the rack profiles must be untied with a crossbar that increases the rigidity of the entire structure of the door frame. Between the crossbar and the upper rail, 1-2 intermediate racks must be installed.
There are three ways to make a crossbar over a doorway.
1st way. In a segment of the PN-profile, equal in length to the width of the doorway plus 60 mm, cuts with a depth of 30 mm are made with scissors. Then the back of the profile is bent at an angle of 90° (Fig. 2, a). The resulting part is fixed with self-tapping screws on posts from the PS-profile of the doorway (Fig. 2, b). The fastening of the sidewalls of the crossbar is carried out on the shelves and the bent back.
2- th way. In the shelves, cuts are made with scissors at an angle of 45 ° and the back is bent. On fig. 2c shows a doorway post with a lintel with shelves notched at a 45° angle and a back bent at an angle of 90°. The jumper is fastened to the rack at four points - two on the bent part and two on the jumper itself. That is, a total of eight attachment points for the jumper.
3- th way. The jumper above the door frame is made from a segment of the PN-profile guide, along the length equal to the width of the doorway plus approximately 200 mm. Having marked the width of the opening on the profile, cut the shelves to the back with scissors and bend the ends at an angle of 90 ° (Fig. 2, d). Attach the finished jumper in place with self-tapping screws through the bent backs (Fig. 2, e). For reinforcement, wooden bars with a section along the width of the PN-profile are inserted into the corners and fixed on both sides with screws at the bend of the profile (Fig. 3, a). This will ensure the reliability of the design. Inserting bars into corners is the "know-how" of Russian masters; there is no such information in the technological instructions of drywall manufacturers.
If one of the above conditions exceeds the norm, then the racks of the partition frame framing the opening must be strengthened. "Rigips" company and German company Knauf (in the sense of the main company in Germany) recommend the use of reinforced UA profiles with a thickness of 2 mm. Their width corresponds to standard CW/UW wall profiles - 50.75 and 100 mm. UA profiles are fixed to the floor and ceiling with connecting brackets.
|
|
Rice. 2. Manufacturing and fastening of the crossbeams of the doorway:
a - the manufacture of the sidewall of the crossbar (the back is cut and bent at an angle of 90 °); b - crossbar with sidewalls (the backs are notched and bent at an angle of 90 °) in the frame of the partition; c - doorway post with plug-in corners and a crossbar with a sidewall (the shelves are notched at an angle of 45 °, the back is bent at an angle of 90 °): 1 - PS profile, 2 - PN profile, 3 - crossbar, 4 - LN9 screw, 5 - bottom bracket for door jamb, 6 - top bracket for door jamb; d - crossbar with sidewall (the backs are cut at an angle of 90 °, the back is bent at an angle of 90 °): 1 - stand, 2 - crossbar, 3 - LN9 screw; e - frame of the doorway with plug-in corners and a crossbar with sidewalls (the shelves are cut at an angle of 90 °, the back is bent at an angle of 90 °): 1 - lower guide, 2 - upper guide, 3 - door jamb rack, 4 - insert corner for the door jamb lower, 5 - plug-in corner for the door jamb upper, b - crossbar.
The corners are fixed to the floor and ceiling with dowels and connected to the reinforced profile with an M8 bolt with a washer and nut. In our practice, this reinforcement is carried out either by pressing into the rack wooden beam with its subsequent fixing with screws (see Fig. 3, a, b), or by installing an additional profile (Fig. 3, c).
The maximum weight of the door leaf depends on the selected profile. According to German and Austrian standards, a door leaf weighing 30 kg can be installed in a CW50 profile frame, 40 kg in a CW75 profile frame, and 49 kg in a CW100 profile frame. When using reinforced UA profiles (thickness 2 mm), the weight of the door leaf for installation in the partition frame increases and amounts to 50 kg for the UA50 profile, 75 kg for the UA75 profile, and 100 kg for the UA100 profile.
Window openings and niches in partitions are reinforced with racks according to the same principle as a doorway.
Making a doorway frame partition near the wall, to which the partition adjoins, is no different from those described above. On the guide profile, which will be attached to the base wall, mark the length from floor to ceiling with lines. Then add to each side the length of a short section of the partition and cut off the excess with sharp scissors. Along the lines of the floor and ceiling, the profile shelves are cut to the back and the tips of the corners are cut a little in these places so that they do not interfere with bending. The ends of the profile are bent along the marking lines at an angle of 90 °. Using a plumb line and a building level, level and fix the guide profile with dowel-nails (Fig. 4).
Changing the layout, or dividing an existing room into separate rooms is not difficult. To do this, you can call a team of repair specialists or do everything yourself, subject to the availability of certain knowledge and skills. Most often, plasterboard doorways are used for interior partitions. The installation process of such a design should be thought out to the smallest detail, since its quality and stability depend on it.
The quality and practicality of drywall in use have been proven for a long time. It is used not only as a material for wall decoration, but also as the basis of structures and partitions that divide a room into several rooms. Each such wall must have a hole for the door, which greatly complicates the installation process. It is important to remember that the doorway must have a certain rigidity in order to be able to place a door frame in it, facing materials, slopes. If the presence of a door is not initially planned, in the future such a need may arise. A well-installed doorway will allow you to mount the door without much hassle at any time.
Drywall wall installation process:
- Frame layout;
- Frame installation;
- Wall cladding with plasterboard.
At the beginning of work, you need to draw a plan of the walls in order to avoid shortcomings and further redoing. Future doorways and the width of the partitions should be marked on the drawing. The first step in installing the wall is to transfer all the elements from the plan to the floor and ceiling of the room.
The presence and location of electrical wiring and electrical appliances should also be considered in advance.
To install the frame, a guide metal profile is installed, which serves as the contour of the partition. Fastening is carried out with a perforator or dowel-nails. Next, vertical rack profiles are mounted, after which the frame is filled with soundproofing material and stitched with drywall sheets.
How to install sliding drywall doors in an interior partition
Sliding doors in a plasterboard partition take up little space and are ideal option for small spaces.
To install such a door, you will need to carry out the following work:
- Calculate the mounting height of the guide and the size of the opening;
- Mount the partition frame;
- Install the door guide;
- Install stroke limiters;
- Finish the frame with plasterboard;
- Laying a clean floor;
- Hang the door leaf;
- Install platbands.
When installing a metal frame, jumpers are used that connect the walls of the structure to increase rigidity. Double vertical racks are also installed, because it is impossible to put jumpers in the space where the door will hide.
We install a doorway from drywall with our own hands
Doorways are made using guide profiles according to a pre-marked marking. The size of the door block significantly affects the final width and height of the opening. Before calculating the height of the opening, you should pay attention to the absence or presence of flooring.
The process of installing a plasterboard partition with a doorway includes the following steps:
- Installation of guides and rack profiles;
- Markup and formation of the design of the doorway;
- Anchoring drywall sheets on the finished construction doorway;
- Installation of a drywall box for an air duct.
Before starting finishing work, it is necessary to check the wiring. To improve sound insulation, it is necessary to foam the gaps between the profile and the boards.
Racks along the edges of the doorway are reinforced with wooden bars that match the profile in size. The presence of a wooden bar significantly improves the quality of mounting a door into a partition from drywall with your own hands, and also improves the rigidity of the structure. Self-tapping screws are used to fasten the bars to the profile.
How to make drywall doors with your own hands
The process of manufacturing and installing drywall doors is not complicated, but the final result largely depends on the planning of the structure.
In the process of manufacturing drywall doors, the following work must be done:
- Install the door frame;
- Sheathe the crate of the door;
- Repair cracks;
- Carry out ground and putty work;
- Carry out the final finishing of the wall.
For the frame, a cut profile is used, on which jumpers are attached to increase the strength of the product. The frame is sheathed with drywall of any size and even with remnants, since the finished canvas is eventually amenable to primer and putty. All cracks and chips that appear as a result of the skin must be repaired with high quality. After that, painting or pasting the doors with photo wallpaper, tiles is carried out.
In some cases, the door structure is insulated with foam, glass wool, polyurethane foam, isolon, or polystyrene, while the material is laid in an empty space and fixed with glue.
In what order is a drywall wall with a door installed
To isolate the passage room, you can use interior partitions for which material with different characteristics A: Moisture resistance and fire resistance.
Since the material is very fragile, it should be handled carefully and carefully to avoid damage.
Stages of installation of an interior partition:
- Preparatory- measurements, preparation of materials and tools;
- Mounting- the process of installing the profile, forming an opening under the door and installing drywall;
- Finishing- treatment of the wall surface with various impregnations, application of paint, tiles, wallpaper.
Immediately before installing the door, it is necessary to divide the material into separate elements according to the preliminary marking of the boundaries. The cut line should be leveled with an edge planer. The frame is sheathed on both sides with drywall using self-tapping screws.
How to sheathe a doorway with drywall correctly
Before sheathing a wall, it is necessary to properly cut drywall sheets with a construction knife. To obtain even borders, place the sheet on a horizontal hard surface and mark with a marker the line along which you want to separate part of the material. The top layer of drywall must be slightly incised. After that, the sheet is shifted to the edge of the support and breaks. At the end, it is necessary to turn it over and repeat the above steps again, as a result of which it will be possible to separate the desired piece of drywall from the sheet.
The sheet and frame are connected with self-tapping screws. Initially, it is necessary to fix the edges of the sheet, and only after that the middle. Between the fasteners, a distance of 10 to 25 cm must be maintained.
It is important to screw the screws completely into the drywall so that the hats do not stick out above the wall level.
The work is carried out in the following order:
- The first sheet is fixed;
- The distance to the ceiling is measured and a piece of drywall of the appropriate size is cut;
- In places where it is necessary to fasten the sheet to another piece of drywall or ceiling, you need to form a chamfer;
- After the first row, whole sheets are installed under the ceiling, and the missing part is attached to the bottom.
How to install a drywall doorway
During the redevelopment of the apartment, the solution of finishing the doorway with drywall is very popular. However, it does not have to be rectangular. Unusual and curved doorways are now in fashion, and with the help of drywall it has become possible to realize any design idea.
At the beginning of work it is necessary to dismantle old door: remove from the hinges and remove the architraves, jambs on the floor.
Installation of a drywall doorway is carried out in several stages:
- Installation of a rigid frame for attaching sheathing sheets;
- Installation of the upper transverse bar to fix the upper dimensions of the opening;
- Measuring the parameters of the box along the width and height of the doorway;
- Preparation of materials for the installation of a doorway and sound insulation;
- Plasterboard marking;
- Fixing drywall sheets on self-tapping screws;
- Pasting seams with serpentine tape;
- Putty and primer of the doorway;
- Final decorative finish.
We make a drywall doorway with our own hands (video)
A drywall doorway can be the highlight of a well-chosen design. A partition with a compartment door is especially relevant in a modern interior. The main advantage of this design is the ease of assembly. Thanks to this, there is no need to pay money for the installation of such a wall and the preparation of the material, because it is very easy to do it yourself.
Registration of doorways from drywall (photo in the interior)
Visitors to the OBI hypermarket order goods for home construction and renovation online. Decorative panels made of strong and durable materials are constantly presented in the electronic catalog. More than 200 items of products from trusted manufacturers are available. The cost of goods ranges from 50 to 4500 rubles per unit. All products are provided with long-term warranty, sold wholesale and retail.
When buying decorative panels, you must carefully select products according to the following parameters:
- . Manufacturing material.
- . Dimensions.
- . Hue.
- . Invoice.
Plastic products are characterized by a minimum price and maximum resistance to moisture. Elements made of wood, chipboard and MDF are not recommended for use in rooms with a high level of humidity (bathroom, kitchen, bathroom, toilet). Products from natural and artificial stone characterized by increased strength and complexity of machining.
PVC panels usually have a solid neutral color. They are often used for wall cladding when performing economy class repairs. Decorative elements made of MDF stand out attractive appearance. During installation, they are protected from the damaging effects of moisture by a protective layer of paint or varnish. mosaic elements are more expensive than other analogues, they are often used for design decoration premises.
When placing an order and choosing goods, buyers of the OBI hypermarket use free consultations of trained employees. Additionally, our resource has built-in services. Services and operational work around the clock.
Payment and delivery methods
- Purchase goods online with delivery
- . You can pay for your order in cash or by bank transfer.
- . You will coordinate the date and time of delivery with the operator by phone when confirming the order.
- . The terms of the free service depend on the city, amount and weight of the product.
- . Unloading goods, lifting and transferring are additional services and may be paid separately, check with the store operator.
Detailed information about the intervals and zones by city, the conditions for unloading and lifting the order are located, where you can independently calculate the cost of your delivery in advance, indicating the postal address and parameters for unloading.
- Order and collect yourself where it is convenient for you
- . When filling out the order form, indicate a convenient date and time for you to visit the hypermarket.
- . You can pay for the purchase in cash or by bank transfer at the cash desks of the store.
Purchased goods can be picked up at any of the OBI stores in Moscow, St. Petersburg, Ryazan, Volgograd, Nizhny Novgorod, Saratov, Kazan, Yekaterinburg, Omsk, Krasnodar, Surgut, Bryansk, Tula and Volzhsky.
Plastic sheets for wall decoration are used quite often. This is essentially a universal material that is suitable for residential and for industrial premises. These products are of several types, and they differ in their characteristics.
Today we will look at what plastic sheet panels are for walls, what is better to choose and their installation rules. Also on the video in this article and photo you can see the different types of finishes with this material and choose the most suitable one.
Advantages
Plastic sheet panels for walls have a number of advantages that allow them to be used for many rooms. But this does not mean at all that there are no shortcomings.
Therefore, before buying, you need to study everything and only then make a decision:
- Decent appearance;
- Simple care. To remove dirt from the veneered panel, you should use the usual detergent and water, but abrasive substances are strictly prohibited;
- Resistance to moisture and preservation of color from sunlight;
- Although the price of plastic is not high, it still needs to be changed sometimes. This is not difficult and fast. After all, the panel is attached to the profiles and you just need to cut the desired size and replace it;
- A huge palette of different colors and shades, with which you can bring to life almost any project, even the most unusual.
- Long service life.
- Resistance to abrasion, discoloration, mechanical stress.
- A variety of textures, textures and colors of products.
- Ease of installation.
- Ease of use. Does not demand special leaving, is easily cleared of pollution.
- Installation on any surface is possible.
- It is allowed to use in rooms with high or low temperatures (baths, balconies, loggias, warehouses).
Plastic sheet panels for walls also have a number of their disadvantages, which should be reckoned with:
- You should not install them in places of direct sunlight, in this case they simply burn out;
- They do not burn, but when directly exposed to fire, they emit harmful gases to human health.
Attention: You should never buy sheet plastic wall panels from unknown manufacturers, give preference to trusted ones. After all, low-quality plastic can be quite harmful.
Varieties of plastic panels
Plastic panels- relatively new material in the construction market.
Applies to both internal and exterior finish walls:
PVC panels for indoor use | Plastic sheets for interior walls have a thinner profile. They do not always tolerate temperature changes. Susceptible to mechanical stress. |
Facade PVC panels | These are more rigid elements that have a thick profile and perfectly tolerate temperature changes and high humidity. When conducting insulation, they are not squeezed out by a heater. |
The finished product is made by heating polyvinyl chloride (PVC), molding and then cutting it. Typically, panels are produced in two groups.
PVC sectional panels | With standard thicknesses: 5mm, 8-10mm. They consist of two sheets of plastic, fastened at a certain step with longitudinal ribs. |
PVC sheet panels | The width of the product is from 20 to 37 cm, the height is 260, 270 and 300 cm, the thickness is 0.4 mm. |
The main difference between the first group and the second is the method of installation. For sheet material, it consists in gluing sheets onto a previously prepared surface.
Living rooms (living room, bedroom, nursery)
One of the important qualities is the aesthetic appearance. Although it should be said that this product is not often used in residential premises. But individual details of the interior are still carried out.
With the help of a competent installation of light and the selection of textures, you can pick up amazing combinations. Smooth, seamless, stone, wood paneling will help complete the design.
Combining an original pattern and a practical surface, the material becomes an alternative to the usual wallpaper. The panels are easy to clean, which is especially important in children's rooms (dust, stains, drawings).
Kitchen
Wear resistance, moisture resistance are the main characteristics that the buyer should pay attention to. This area requires the highest quality material, which is easy to care for.
To decorate the room, it is best to choose pastel-colored panels (see Finishing the kitchen with plastic panels or a new boom). In this case, the trace of greasy stains will not be noticeable (in case the material is not of high quality).
Corridor
It is recommended to use moisture resistant panels without decorative elements. This will ensure easy care and ease of use. Often when facing walls, two types of panels are used: dark and light. This is done for reasons of practicality.
Offices
A huge variety, characteristics, practicality has made the material common for finishing office space. The main advantage is the affordable price. A rich selection of products allows you to use them in the design of any type of premises, betraying originality and sophistication.
Cellars and warehouses
Fire safety, low cost - characteristics due to which steel panels are widely used in interior decoration storage facilities. The material allows you to sheathe large surfaces and is easy to use. Ability to work in conditions high humidity and the dramatic temperature difference makes it one of the best.
Plastic panels must not be used in places intended for the evacuation of people. When ignited, they release toxic substances dangerous to human health.
Sheet plastic for wall decoration offers a large selection of finishes. This and various combinations with other materials and simply interesting solutions. The gallery presents various options finishing with this material.
It is possible to select zones in the room with the help of sheet panels and the desired pattern, even if it is not large
Siding is quite often used in facade cladding (see Facing with facade siding: the entire cycle of work). It not only looks great, but also allows you to immediately make and warm the room.
The combination of different colors of the panels allows you to make original drawings and improve the interior of the room.
Placing the panels vertically, you can always visually raise the ceilings and increase the volume of the room.
Usage various kinds panels will highlight different planes in the room.
For large rooms, contrasting colors are often used and this can not only add volume, but also be quite attractive.
Panel installation
Sheet plastic for the walls will follow the contour of the base plane and therefore it must be perfect. After that, it should be quality installation, only then will you get an attractive coverage. Now let's talk about the installation rules.
crate
Plastic sheet for walls is attached to the crate. In rare cases, it can simply be glued to the walls, but for this they must be perfectly even. Therefore, most often this is done precisely on the crate.
It can be made of metal and wood:
Metal crate | The fastening structure can be made of S-shaped profiles. Depending on the material of the walls, installation is carried out with the help of building screws and “crackers”, dowel-nails.
|
Wooden crate | This material is more convenient when working and everything can be done with your own hands without any problems. Especially if it's hard to reach places. Pretty easy to handle
|
Plastic installation
The installation instructions are not complicated. Installation of PVC panels is carried out on a pre-prepared structure made of rails or bars - a crate or on a prepared wall surface.
wall decoration PVC panels carried out in the following order:
- A crate is installed on the prepared base;
- Mount the initial, final and guide profiles;
- The initial panel is installed with a narrow shelf towards the first profile;
- The panel is fixed with a staple device on the crate, after which the remaining products in the row are installed, with the exception of the last one;
- The last element of the row is shortened from the side of the wide shelf with a small gap, moving along the board;
- With effort, the final element is inserted, gently bending the shelf with a spatula and attaching it to the crate.
Checkout modern interior using plastic panels - painstaking work that requires time and precise adherence to technology to achieve a high-quality result. The option of using such material is especially popular for finishing balconies and bathrooms.
A variety of colors, prints, patterns and textures allows you to withstand, and the characteristics meet the most capricious operating conditions. By following the simple rules for installing panels, you can get the desired result.
- It is more practical to install panels in rooms with a wet operating mode (bathroom), sudden temperature changes (balconies), prone to pollution (hallway).
- When used in living rooms, the need for normal air circulation should be taken into account. This is done through natural ventilation or by installing an air conditioner. This is especially true when lining with a seamless material.
- It should not be installed in a children's room, in the kitchen (especially in the cooking area), sports areas.
- During installation, handle the tool carefully so as not to damage the material.
- The finish profile should always be used. It is an important element without which the work will look rough and careless.
- Before choosing panels and profiles, it is better to give preference to proven brands (not quality materials may crack, bend, jam at the joints).
- The crate is best done with maximum precision. The evenness and convenience of work directly depends on how you installed and fixed the frame.
You can install sheet plastic panels for walls completely on your own. The most important thing is not to rush and use quality materials.