How to finish the door slopes? How to make slopes on the front door with your own hands: tips and tricks Plastic door slopes

To make door slopes with your own hands, it is desirable to have certain skills in finishing work. It is necessary to have basic knowledge about the properties of the materials used and the rules for puttying. Slopes are the perfect completion of the doorway for both entrance and interior spaces.

Slope finishing ennobles the doorway and gives the door a complete look

Types of slopes

Finishing door slopes is an equally important stage in repair work than directly installing the door itself. The final result of the whole process depends on the quality of the work and the selected materials, which will directly affect the overall picture of the interior.

Distinguish between internal and external slopes. The latter type refers to the entrance doors and has many subtleties and nuances. It is also necessary to distinguish between their types depending on the method of facing. So, consider how you can finish the slopes of the front door:

• plastering followed by painting or wallpapering;
• overhead panels made of wood or MDF;
• plastic.

A modern option for finishing slopes - sheathing with the same material as the platbands

Overhead panels can be mounted in several ways. When installing on a perfectly flat surface, it is enough to use liquid nails. If profile guides are used, a distinction is made between vertical and horizontal installation. In the first case, a sheet of the required size is cut out and screwed to the profile. In total, 3 parts are required: 2 side and 1 top. When laying horizontally, the lamella parts are joined in turn in the direction from the bottom up, each 3-4th element is fixed to screws or liquid nails.

Surface leveling

Before you make the slopes of the front door, you need to prepare certain tools and materials. Since it is first desirable to level the surface of the wall, you will need:

• primer;
• cement-sand plaster or starting putty;
• finishing putty;
• construction mixer;
• bucket;
• brush or roller;
• spatulas;
• corner;
• grid for plaster;
• masking tape.

In addition to all this, you may need metal or plastic profiles, drywall, liquid nails, insulation, front finishing material, a hacksaw.

First of all, regardless of the type of lining chosen, it is necessary. Before starting work, make sure that nothing superfluous remains on the surface: old finishing material, mounting foam, various contaminants, etc.

If the differences in the doorway are large enough, then it will be quite difficult to align the slopes from scratch, in this case, you can make the task easier and use drywall. They fix it with metal profiles, but if the wall does not have significant differences, you can put the sheets directly on the solution.

How to plaster door slopes:

1. Cover the details of the door structure with film and masking tape for protection;
2. Clean the surface of dirt and carefully primed;
3. In a bucket, prepare the starting mixture to level the surface;
4. On the dry surface, apply the solution with a spatula and level it to the required thickness, observing the level. To improve adhesion, you can sprinkle the concrete with water from a spray bottle;
5. If the wall was severely damaged during the installation of the door, it is necessary to use a plaster mesh. Corners are aligned with corners. If necessary, drywall can be used;
6. After the starting layer has dried, it is necessary to wipe out all the irregularities and re-priming the slopes;
7. Use finishing putty to bring the surface to perfect condition and rub again. Repeat if necessary.

Traditionally, many homeowners escarp entrance doors plastered

After the slopes have been leveled, you can proceed to their final finishing, paint, wallpaper, tiles, decorative plaster and other materials can be used for this.

MDF cladding

If you want to give your doors a more luxurious look, then it is better to use MDF panels to match the main structure. How to make slopes on doors using overlay panels:

1. Decide on the type of attachment. If the wall surface is perfectly flat, you can fix the panels with liquid nails. If the plaster is far from ideal or is completely absent, it is better to fix them on the frame, most often it is a metal structure or wooden blocks;
2. Install the frame around the entire perimeter of the slopes;
3. Cut out the details of the required size;
4. Attach the MDF to the frame and secure. The ideal solution is to use L-shaped panels that cover the corner of the wall.

If you used simple panels or a horizontal laying method, you need to hide the joints with platbands or plaster the seam.

Examples of finishing slopes with MDF panels

Use of plastic

The cheapest and lightest material for slope sheathing is plastic, it is quite easy to cut, which is also a huge plus. In addition, you can choose not only the standard white version, but also colored models or imitations of various materials such as stone, leather or wood.

1. First, prepare the surface and install the guide profiles, they look like F-shaped strips;
2. From plastic, cut parts of the required size. In order for the cut to turn out neat, it is best to use an electric jigsaw, in extreme cases - a hacksaw with fine teeth;
3. When laying vertically, install the side pieces first, then fix the top slope. If horizontal elements are mounted, they must be tightly fitted at the points of entry into the grooves, and it is desirable to fix every third part additional materials: screws or glue. They are also installed at the beginning on the sides, gradually approaching the top;
4. Put corner caps on the extreme cuts;
5. All joints and seams are worked out with a sealant.

It is worth mentioning that horizontal laying is more appropriate for ribbed plastic like siding and for wide slopes.

Options for finishing door slopes with plastic

Additional insulation

When finishing the entrance door slopes using a frame, one important question should be solved - is it necessary to additionally insulate the doorway? The fact is that between the panel and the wall there is an unfilled space that can pass cold air to the apartment, so it is better to immediately insulate the slopes, since after the repair is completed, it will be quite difficult to correct the situation.

The slopes of the entrance doors can be insulated using the following materials:

• mineral wool;
• mounting foam;
• felt;
• ecowool;
• glass wool;
• polyurethane foam;
• expanded polystyrene;
• foam rubber
• etc.

Additionally seal all joints and seams with sealant wherever possible. Also keep in mind that almost all materials lose a percentage of their volume over time.

Proper finishing of the slopes of the front door involves a layer of insulation

Which option to choose

Not every option will be appropriate in a particular case. What kind of finishing is better for external work, and which one is better for internal work? Do-it-yourself finishing of the slopes of interior doors allows you to save on materials. For this work, you can use the remains of wallpaper, paint and other materials, since there are no special requirements for internal slopes. Too massive and rough constructions are unlikely to be appropriate here.

And what is the best way to make slopes for front doors with your own hands? When it comes to exterior finishes, the best option is plaster, it is resistant to atmospheric influences, is not afraid of moisture, looks neat and easy to care for, besides it will last a very long time, but it is better to refuse plastic, as it may not withstand frost. For interior work, you can use almost anything. It should be noted that for private houses it is better not to use drywall when installing slopes, because even a moisture-resistant look can deteriorate over time. The optimal solution is MDF panel: solid, beautiful and reliable.

As you can see, in order to correctly make slopes for an entrance or interior door, it is necessary to follow a certain work technology, which depends on the specific material. The easiest way is to close the wall with ready-made parts, but this method is unlikely to be appropriate everywhere. Plaster is a versatile and most reliable option.

When the repair and installation of the front door is completed, doorway around it often has an unsightly appearance, which can spoil the feeling of joy after the completion of the repair. In addition, unshaped edges allow drafts to penetrate inside and lower the temperature in the room. Therefore, it is very important to correctly make and arrange door slopes in order to prevent the influence of all these negative factors.

Peculiarities

When doors are already installed in the apartment, many people think that protection from external factors, such as noise and cold, is provided. But it is not so. It is necessary to make additional finishing in order to complete the repair and give the doorway a harmonious appearance. From the outside, the entrance doors are always trimmed with platbands or a special solution during installation, but the internal slopes of the master during the installation of the door frame are always left to the discretion of the owners of the house.

Finishing the slopes is not included in the work of installing the door. That is why, in front of your eyes, concrete, brick or other materials without exterior finish. To hide all this, you need to correctly arrange the slopes. Not all companies that install doors provide additional services for the design of slopes. That is why this task is very often shifted to the shoulders of the owner of the house, and he has to do this work on his own.

The purpose of installing this element is to give an elegant appearance to the door and doorway, as well as to complete its outlines.

In addition, door slopes are installed in order to hide all door fasteners from prying eyes and increase protection against burglary. In addition, with their help they provide heat and sound insulation, as well as protection from dust and dirt flying from the street or from the landing.

Slopes are a very important and necessary element, which can make the doorway more presentable and tidy. They are beautiful design that complements any hallway. The slopes are designed in accordance with the style of the front door, as well as in accordance with its colors and with the stylistic design of the hallway. That is why choosing the right slopes is a very important task.

Apart from the decorative function, the slopes also very effectively insulate the door frame and allow you to hide the joints between the box and the wall. Slopes also hide mounting foam. Thus, this element also allows you to additionally perform the role of thermal insulation. Mounting foam, located in plain sight in the room, absorbs moisture and loses its protective properties, and at the same time it looks very neat.

Thus, the door slope is a very important element that is paid attention to during the repair.

Kinds

There are three main systems of slopes for door structures, which differ in the method of installation:

• Applying cement to the wall and subsequent plastering. Such a finishing system is considered the most reliable and quite cheap. But not everyone can cope with such a task, it is a very time-consuming and painstaking process. In order to create very even and high-quality surfaces, it is necessary to have the skills to prepare the right plaster mortar and experience in its uniform application and distribution.

• Slope design system using panels and special glue. In this case, an adhesive mixture is made and ready-made finishing panels are applied to it. This principle is quite costly. In another way, it is called wet.

This process is very time consuming as each layer of adhesive needs to dry well before you apply the next layer. But even with the long duration of such work, they are quite simple and even a beginner in the installation business can handle them.

Fixing the finish to an already finished frame. It's very simple and fast way, which allows you to achieve ideal in shape and very neat door slopes. So you can not only hide from prying eyes concrete wall, bricks and polyurethane foam, but also close all wires and other communication networks.

In addition, you can install additional lighting in the door frame and beautifully play with the light in this area of ​​the room. This option is suitable for panel apartments as well as for a private house.

The only disadvantage of this method is the low strength and susceptibility finishing materials even on a steel frame to mechanical stress. Thus, this option will be more prone to hacking. As a rule, it is used for finishing wooden door structures inside the apartment.

For more information on how to make a slope of an MDF front door, see the following video.

materials

For the design of slopes, high-quality and stable finishing materials are often used.

Dye

This is one of the most popular coatings, which allows you to decorate the door slope very brightly and interestingly. You can make it an interesting accent of your hallway. In addition, you can choose the paint to match the color of the door. In this way, even a metal door can be decorated. You can buy water-based paint or use the usual version. In addition, you can apply a beautiful textured pattern that will look very original and will decorate any hallway.

Wallpaper

This is a great solution for those who decide not only to change the door in the hallway, but also to completely renovate the hallway. Decorating the door slope with wallpaper is quite simple, but for this it is necessary level ground. Very often, the same wallpaper is used on the walls as on the slopes. This creates the impression of a monolithic surface. Thus, it is possible to visually expand the doorway and the space of the hallway as a whole.

One-sided sandwich panels

These panels are a sheet of polymer plastic, on which a layer of extruded polystyrene foam is glued. It has a fairly dense texture, which has excellent soundproofing properties and acts as great option for insulation. Thus, you will not need to additionally insulate the doors and take special measures for soundproofing.

Such panels are very light in weight and therefore adhere well to the door even with special glue without additional fasteners. In addition, their design can be very diverse, there are even wood-like models and products that imitate other materials and surfaces.

Plastic panels

This is a fairly easy-to-install option, which has an interesting decor. Plastic panels are somewhat similar to the previous version, but they are less reliable and thinner. If the slopes are deep, then plastic laying is not recommended.. This is due to the fact that it can be easily deformed and damaged. Plastic panels will not give the same rigidity throughout the door slope. But their undoubted advantage is an interesting and varied design.

Among the plastic options, vinyl panels are very popular. They are pretty reliable. In addition, if this element of the door structure is sheathed with vinyl, it will respond well to temperature changes and air humidity levels, which is typical for areas near the front door. Therefore, they are often used for sheathing slopes.

MDF

This is a very durable material that is resistant to external influences. It perfectly withstands various impacts and there are practically no scratches and other point damage on its surface. Externally, this material is similar to wood panels, so it looks very elegant. In addition, MDF is very easy to install and can be installed on almost any door slope. These models look best on wooden products , but there are also models for metal doors.

parquet board

This natural quality material perfect for decorating door slopes. Usually it is chosen for wooden doors or the color floor covering. It is important to choose the most appropriate tone, texture and relief. Thus, this composition will look very beautiful and harmonious. Manufacturers present a huge number of types of parquet boards that can outwardly match any wooden door, wenge models are especially beautiful.

Laminate

Another option that is perfect for finishing slopes. It can imitate a door pattern, so it is perfect for models made from natural materials. They can repeat the pattern of any other materials, including stone, marble and other finishes. Thus, it can be matched to almost any type of door leaf.

Since laminate is often used as a floor covering, it is distinguished by its strength and endurance, so the slopes will last a very long time.

But there are a number of materials that are used to insulate the door frame. For this, foam, penoizol, metvat, as well as other materials are used. But in the case when the width of the slopes is small, it is quite difficult to make insulation, so sandwich panels are perfect. For finishing wide doorways, frame slopes are often used. When installing thin sheets, such as plastic panels, heaters are often used - polyurethane foam, sealant and other materials, acting as a heat barrier.

What drywall to use?

Any drywall is a layer of gypsum between two strong cardboard sheets. This is one of the easiest materials to install. They allow you to level the surface without putty and primer. Even a novice in this business can handle the installation of drywall sheets.

In addition, this design of the slopes allows you to get rid of excess debris that could arise when using a different finishing method. In this case, the slopes are perfectly smooth and even, which gives room for imagination and their further design.

For the design of slopes at the front door, it is important to take not standard models, but materials that differ in quality and water resistance. It well withstands the increase in air humidity characteristic of the hallway. To ensure greater safety, it is better to give preference to sheets with the addition of fiberglass, since such material is non-flammable and provides insulation for the entrance structure.

How to close up for a metal sheet?

To finish the slopes at the metal entrance door, the frame method is most often used. To create the base, you must use metal profiles. Finishing with wooden bars is also acceptable. It is important that the canvas adheres tightly to the surface.

To strengthen the metal door frame, you need to install a lintel on the supporting part of the structure. Their installation at the corners of the structure is especially important. At this stage, you can lay cables and other wires. After that, it is necessary to fix the selected canvas with screws or nails.

It is also very popular to seal the slopes of metal doors with a cement-sand slope. But for this it is necessary to level all the slopes with a primer and place emphasis on the subsequent installation of finishing materials. For metal construction it is important to take into account the thickness of the solution layer and the thickness of the finishing material so that such a finish is not too massive and does not violate the overall picture of the door structure.

For sealing slopes approx. metal door drywall works great. This is due to its small thickness and versatility. But this material requires additional insulation.

Finishing after installation

After installing the door, it is important to correctly arrange the slopes in order to ennoble the appearance of the entrance to the house as a whole. This can be easily done with your own hands, the main thing is to correctly align the door slopes from the inside. Highly interesting option finishing after installing the doors is the use of extensions. You can also use the following options.

Natural or artificial stone

It's pretty fancy and beautiful option, which performs a decorative role. It is quite expensive, especially when it comes to natural stone. This method has many advantages, since the material is considered very durable and of high quality. Natural stone is a completely eco-friendly option that is resistant to external mechanical influences.

But cheaper artificial stone is not of the same quality. It has a large number of disadvantages, since it is made on a gypsum basis. It is easily damaged and crumpled. In addition, it can easily crumble or warp when exposed to water or high humidity.

Tile

This method of finishing after installing the door is quite complicated. Not all tile options can be used for this. In particular, it is better to avoid using glazed models, as they will look very strange and cheap on the door slopes. It is best to give preference to clinker tiles.

This option can mimic brickwork or a natural stone. Therefore, it can be chosen for any stylistic design of the hallway. It is best to choose not very easily soiled and not glossy tiles. This finish option is good because these surfaces are quite easy to care for. In addition, manufacturers present a wide variety of models for decoration.

PVC panels

A very simple finishing material that is cheap, beautiful, but short-lived. Some low-quality models can be easily pierced, even leaning on them with an elbow or hitting them hard with a foot.

Decorative plaster

This is a very interesting, but rather laborious installation option. Applying decorative plaster is a whole art, therefore this process it is better to entrust professionals. But in the end, the slopes and the space near the door can noticeably change.

All finishing methods are used both individually and in combination with each other. So you can not only beautifully design the door structure and slopes, but also make the door more reliable, insulate and protect it from external factors and from breaking.

Mounting and design options

There are two main options for mounting slopes:

• frameless;
• frame.

Before moving on to finishing, you need to make sure that the structure is installed correctly, that the exact parallel between the opposite borders of the door frame is observed and that all seams are sealed. First of all, it is necessary to check the structure for cracks. To do this, light a match or candle and run it along the entire doorway. Where the flame begins to deviate or even go out, it is necessary to additionally insulate the slopes and add sealant.

When all the insulation work has been completed, you need to cut off the excess dried layer polyurethane foam and additionally cover the door frame with masking tape. After that it is important to get rid of old plaster and loose concrete and brick wall elements.

After that, you need to move on to plastering. First you need to completely clean the wall of construction dust and level it. Then you need to use a deep penetration primer. It will make the base of the frame more durable and even.

It is very important to pay special attention to the concrete lintel on the door. For its processing, it is better to use the so-called concrete contact.

If the surface does not absorb moisture well, then it is also necessary to use a special primer. After the soil layer dries, you will need to install the profiles. But before that, it is better to wait about 8 hours until it dries completely. Profiles are necessary in order to even out the layers of plaster on all slopes.

To do this, it is necessary to mark the position of the vertical line on the side of the door about 3-4 cm with a laser or the simplest level. There it is necessary to drill several holes with a diameter of 6 mm in increments of 30 cm. Dowels are inserted into the holes, and then the level of their caps is leveled with twine. After installing all these items it is necessary to check their correctness and even vertical. By the same principle, it is necessary to install a profile on top and on the opposite side of the doorway.

After the installation process is completed, it is necessary to make a cement mixture. It is best to use sand and cement grade M150 for this. All these finishing materials must be sieved through a sieve with small cells. To create a high-quality solution, it is necessary to mix sand with cement in a ratio of 3: 1. You need to gradually add clean water to the dry mixture and at the same time stir the resulting solution with a special drill nozzle.

When the mixture becomes homogeneous and thick, like dough, the solution can be used to finish the slopes. Using a spatula, it must be sharply and quickly thrown onto the wall and ironed, closing the profiles. Thus, you can make a perfectly flat surface without unnecessary deformations.

The panel version without a frame is simpler. In this case, laminate, drywall, sandwich panels, MDF, chipboard and other options are often used. And you absolutely do not have to smooth the surface of the slopes. Finishing is carried out by mounting on glue. It is important that the surface is straight. There should be no defects or irregularities on the surface.

Even if the door frame itself has some defects, they can be corrected using this design of the slopes. In this case, it is necessary to additionally plaster the door exactly in the places missing for a flat surface. If the original surface is flat and smooth, then the frame method will be very simple. Initially, you need to apply primer to the base where the panels will be fixed.

Then you need to measure all the slopes and select the right amount of finishing materials. On the panels, you need to make all notes and put points. Then you need to connect all the lines and check them with a tape measure and a special square. This must be done very carefully. A sheet of such a panel must be cut into the required number of individual elements and prepared for installation.

As for laminate or parquet, they can be installed both vertically, one for each slope in width, and horizontally, using several short panels. Then, it is necessary to apply glue on the finishing material using the nest method in increments of approximately 15 cm in the shape of a square. All adhesive spots must be dried a little so that a film begins to form on their surface. Only after that it is possible to apply slope elements, but it is important to be very accurate, since it will be possible to align the finishing panels only a couple of centimeters, no more.

Then, starting from the top and moving down, you need to gently press the panels against the wall, but do not press hard on them so as not to push them through. This is especially true for plastic panels.

Design and decor

The design of the door slopes is the final touch after finishing them. As a rule, models made of MDF and decorative materials do not require additional decoration, since these materials look quite elegant without additions. This also applies to options with laminate, parquet and plastic panels. To complete the finishing work, in this case, platbands are installed and the joints and all joints are masked with the help of special furniture stickers or mastic, which is selected in exact accordance with the color of the finishing materials.

But if the doorway is only plastered, then it is necessary to use other methods of decoration for it. So, paint is used for this, decorative plaster or wallpaper. But before that, the slope is covered with two layers of putty to hide the bumps and get a smooth layer. When finishing with paint, a primer is applied first, and then a layer water-based paint and a bright accent on the layer acrylic paint. So you can interestingly arrange the slope and make it very bright, playing in contrast with the door. This decor looks especially interesting in black and white.

Another option for finishing is wallpapering. But it is better to choose them in the color of the walls in the hallway, so either you need to choose the most similar coating, or finish both the slopes and all the walls with one material. If you have chosen wallpaper only for the decoration of slopes, then it is better to pay attention to options without a pattern, as they may look a little strange near the door. This is due to the fact that most doors have a classic simple design.

Wallpaper should completely cover the entire width of the door slope, taking into account the overlap over the corner line, so that you can cut off the excess at any time. Wallpaper can be textured, embossed, and even have an interesting mother-of-pearl tint. They will look very beautiful and elegant. But try to use soft wallpaper for decorating door slopes, which can also be washed and cleaned. This is due to the fact that dust and dirt from the street very often accumulates near the front door.

When changing doors in an apartment, a person inevitably faces the question: “How to finish the door slopes?”. Even if the installation of doors is carried out by an invited specialist, he will not help you in this matter.
The master will only install the box according to the level, filling the seams with mounting foam, hang door leaf, insert accessories - and that's it. What to do next, you will think for yourself.
We will tell about everyone options finishing slopes, and how to do it yourself. There are several types of materials that can be used for this purpose.

Most often, this method of leveling the slope is resorted to when the walls of the premises are also sheathed with drywall. Depending on the width of the slope and the degree of its unevenness, finishing can be done in two ways.
So:

• If the mounting seams are small and the slope is not badly damaged, the parts cut from the GKL sheet can be glued using gypsum glue. To do this, the surface on which the gluing will be carried out must be well cleaned and covered with a primer layer.

• Naturally, it is necessary to cut the details of the slope as accurately as possible, taking into account the angle of the slope. Installation begins with the installation of side panels.
  Dilute the dry adhesive mixture with water, as prescribed by the instructions on the package. Apply the finished adhesive in a continuous layer on the slope part and press it against the prepared surface.
• When the panels are installed, they must be fixed with masking tape and allowed to dry with glue. Then all the seams need to be puttied, and then cleaned with sandpaper (zero).
  After applying another layer of soil, the slope is ready for subsequent finishing.

• Finishing door slopes in the second way is the installation of plasterboard panels on a frame made of aluminum profile. It is more complex, and is used for frame sheathing of the walls of the room, which significantly increases the depth of the slope.
• This is the prerogative of specialists working with drywall - few people can do it on their own without having certain skills.

To protect the corners of the slopes from accidental damage in the future, they are glued with decorative plastic corners. This applies not only to plasterboard slopes, but also to plaster and plastic ones.

Plaster slopes

Considering that in most residential premises the walls are plastered, it is quite logical that do-it-yourself door slopes will be finished in the same way. Special knowledge is not required here, only some tools are needed, without which an even angle will not work.

Tools and materials

To mix the solution, in addition to the container, you will need a drill with a mixer nozzle. To provide a slope with straight lines, you need: two-meter building level and rule.
We also need two spatulas: one with a width slightly greater than the width of the slope, the second is smaller. To prime surfaces, it is convenient to use a flat brush.

So:

• If you do not plan to use plastic corners for subsequent finishing, you can protect the outer corners of the slope in another way. For this purpose, a perforated metal corner is also used, which, before finishing the door slopes, is attached to the base surface of the slope with liquid nails or mounting foam.
• To strengthen the slope plane, or an opening without a door, a plaster mesh made of fiberglass is used. And there is a variant of the corner, combined with the grid into a single element - it is very convenient to use it.

• To prepare the solution, you will need to purchase dry gypsum plaster diluted with water to the desired consistency. To save the solution, foam may be needed.
• If there are deep potholes in the slope, or its thickness exceeds two centimeters, the foam pieces are placed in the deepest places, and a layer of plaster is applied on top.
• In order not to spoil the door frame, its surface is pre-pasted with masking tape. Only after that you can start priming and plastering the slope.

The last step in the rough finishing of the slope will be the processing of the plastered surface with fine sandpaper to achieve smoothness, and another layer of primer. To see how the plastering of door slopes is made - videos, of which there are many on the Internet, will help you a lot.

Slopes made of plastic

The easiest way to trim the slope is made of plastic. The price of this material is the lowest compared to the rest.
The only “but” is that plastic slopes will not look harmonious everywhere. The most appropriate is to finish the slopes of windows and doors with plastic, if a window, door, or wall sheathing of the room is also made from it.
The ideal option for such a finish is usually kitchens, loggias, bathrooms.
So:

• The most important thing when working with plastic is to achieve the most even and accurate cut. To do this, it is better to use an electric jigsaw, and not a knife.
  Naturally, the measurements must be made accurately, then it is much easier to fit the parts to each other.

plastic walls and slopes

• For window slopes, white sandwich panels are most often used, and any PVC panel is suitable for finishing the doorway. If this is a balcony door, the slopes of which are made of colored plastic, then the slopes of the window next to it are decorated in the same way.
  In the picture above good example such a finish.
• If the doorway during dismantling old door suffered a lot, then before finishing the door slopes with plastic, it is better to first remove the plaster slope with a margin of 1 cm. It will not be necessary to grind it under the plastic, and the solution can be used not gypsum, but cement.
• If there is no significant damage to the opening, the potholes can simply be filled with mounting foam. The same is done when MDF panels are used for decoration.
• To mount the PVC panel, a starting plastic profile is fixed to the door frame with self-tapping screws. The side parts are installed first, and then the horizontal part.
  Any universal glue intended for working with this material is applied to the plastic.
• The panel is inserted into the profile groove and pressed firmly against the surface. Then the glued part must be additionally fixed until the glue dries completely.
  You can do this with masking tape, or just something to support.

When the panels are mounted, the seams between them must be filled with sealant, and then closed with decorative corners. On this finish slopes on balcony door finished.

wooden slopes

Considering that interior doors are made of wood, it is quite logical that the slopes can be made of the same material. This design of the doorway in any interior will look harmonious.

So:

• To finish the slope, you can, of course, use solid wood panels, but veneered or laminated MDF is most often used. The usual laminate used for flooring is also suitable.
  The main thing is that its color should be perfectly matched to the color of the door.
• The technology for mounting wood panels is similar to plastic, but instead of a guide profile, there will be planks that are attached to the base surface with dowels. Further, the panels are screwed to the rails with self-tapping screws, not forgetting to apply glue to the back side.
  The joints between the panels are also sealed and closed with a corner.

• There is another option: when buying doors, you can immediately buy additional trims in color. Sometimes they come together.
  They are made of chipboard, covered with a PVC film that imitates the texture of wood.
• Extensions can also be used if the width of the doorway is larger than the width of the box. Since these strips are attached directly to the box, they mount the extensions in the groove located on the back side even before the door is installed.

Sometimes door slopes are trimmed with decorative stone. This option is more suitable for front doors.
Indoors, such decoration is rare - mainly in design projects, but in the interiors of mansions. A floor or a fireplace can be laid out of the same stone, appropriate accessories for decorating the room can be used.
In this case, the slopes of decorative stone look original and out of place.

Finishing methods and their advantages

You can close the slopes using the following methods:

• applying cement mortar to the surface of the walls. This method has become quite widespread among both experienced professionals and beginners. However, along with the budget, there is one solid minus - it is very difficult to prepare a cement mortar, however, it is very difficult to apply it to the wall, one cannot do without practical skills in this matter;
• application of the adhesive mixture. Such material will cost a pretty penny, but working with it is much easier, which a beginner will certainly appreciate. Glue is applied to the surface in several layers;
• frame installation. Not the most durable material, but it will reliably hide the wires. In addition, the surface as a result is perfectly flat.

In any case, you need to make slopes on the doors. And the point here is not only in the aesthetic appearance, but also in your comfort and safety.

Finishing preparation

Regardless of which finishing method you prefer, there is no escape from standard preparatory measures. To prevent damage to the door leaf, it must be covered with masking tape or a film. Only then proceed to leveling the surface. All irregularities and roughness should be carefully smoothed out. For those who decide to use a special solution for finishing, dust removal is especially important. It must be removed from everywhere, literally from every centimeter of the surface.

Remember: the reliability of bonding materials depends on this. Sweep dust with a regular brush. The main thing is that she has a hard pile. The next preparatory stage is the application of a deep penetration primer. After that, if desired, you can lay an electric wire on this surface.

Plastering

How to properly trim the slopes of the front door - you will have to face this question if you need to change the door in your own home. There are many ways to close slopes. If you prefer to plaster them, you should follow the whole process in stages:

• prepare the surface. It is recommended to apply a primer;
• The next step is to align the corners. Reinforcing corners are often used;
• further perforated corners are attached. Mount them already on the finishing putty. Thus, they will stick securely, and as a result you will get perfectly even slope angles;
• very often, specialists have to deal with the problem of uneven walls. It is really possible to fix the slopes of your front door with your own hands at the stage of finishing the slopes of your front door: a narrow strip of drywall is fixed from the door jamb;
• further finishing of the door slopes is carried out using putty. It is not difficult to apply, but it can take a lot of time. It all depends on the composition of the putty itself and the thickness of the layer in which it is applied;
• the final stage of plastering is the application of a primer.

At the end of the work done, the surface can be freely painted or, if desired, pasted over with wallpaper.

Bonding material to mortar

Installation of slopes on a new front door can be carried out using a special adhesive mixture. This method is not among the cheapest, but the ease of use of the material and the result justify the money you spent. Wet glue is applied in several layers. Do not forget to allow the surface to dry completely after each step.

Frame mounting

How to close the slopes on the door? Very often, the method of fastening materials directly to the frame is used. In this case, no special preparatory work is required from you. You just need to apply a primer to the surface. The implementation of this method of finishing slopes requires metal profiles (they are suitable for installing plasterboard structures), wooden blocks. First, the structure itself is fixed, and then the coating. Sheathing materials are different.

Modern experts very often prefer to install MDF door slopes. These plates are characterized medium density. In the installation of this design, you can use ordinary screws and cloves. What is remarkable about this material is its aesthetics. Besides, his technical qualities speak of high reliability of the coating.

Door slopes from the laminate are installed in approximately the same way as the MDF board. Among the key advantages of this material are reliability, a wide color spectrum, as well as good insulating characteristics and ease of cleaning from various contaminants. When installing the laminate on an already prepared frame, consider the fact that the doorway will decrease slightly. In addition, one significant drawback catches the eye: the laminate is exposed to moisture.

Drywall

Drywall is also often used for sealing slopes. Durable and reliable, cheap and suitable for long-term use, this material is widely used by both professionals and beginners. Install it on a structure made of metal profiles. Fasten with self-tapping screws. Finishing the installation, be sure to put the perforated corners. Now you just have to treat the surface with putty.

Door slopes made of drywall or plastic - a budget option which has many advantages. Whether you choose a plastic material or something more durable is entirely up to you. The main thing is that the finishing of the slopes combines both a neat appearance and reliability.

Video "We make slopes of the front door"

Slopes on the front door: how to arrange it yourself

Often, the entrance opening inside is made out with the help of slopes on the front door. How to choose a material for finishing and make beautiful slopes, read the article

How to finish the slopes of the front door: different options

Finishing the slopes of the front door can be done different ways. Each of the available options has its own advantages and disadvantages and is selected individually. It is advisable to take into account many factors that lie in the overall interior design, possible financial costs, as well as the skills needed to complete all stages.

Reasons for doing the work

How to trim the slopes of the front door? This question always arises when there is a need for this kind of finishing. There can be many reasons for doing this:

• Installation of a new structure. This is the most common situation. During the installation work, adjacent areas are destroyed. It often happens, especially in old houses, that there is a complete shedding of the old layer of slopes, because they are made of plaster. It must be taken into account that the new door must be installed correctly, without distortion, in order to exclude subsequent repair work.
• The appearance of defects. Over time, any finish becomes unusable. The same situation occurs with slopes, especially if they frame the entrance. Cracks, shedding, traces of mechanical impact appear on the surface. It is very important to assess the situation in time in order to install new door slopes without unnecessary work.
• Changing the general appearance of the room. Indeed, a new do-it-yourself facing of entrance and interior doors is necessary when the design of adjacent rooms changes. Sometimes it seems that the door slope is an area that does not affect the overall appearance of the interior. This is an erroneous opinion, because even such a seemingly insignificant detail plays an important role.

Entrance door trim options

On a note! There is another reason for replacing slopes, which is the appearance of mold and mildew. This situation will require cleaning the surface to the ground, cleaning all affected areas and impregnation with antiseptics. You should immediately find the causes leading to the appearance of this problem.

What material to choose for the slope device?

There are many options that allow you to do the slopes of the front door with your own hands.

This finishing material is used everywhere. It must be borne in mind that this option has the lowest cost. All work is carried out independently, without the use of special tools. More recently, this method was one of the main ones, but recently its popularity has begun to fall. There are many reasons for this, among which stands out - not the most beautiful visual appearance. Of course, this state of affairs is easy to fix if you use decorative and textured plaster.

plastered slope

• Drywall.

The popularity of GKL plates is only growing. This material allows you to perform all the work quickly enough. But this is true for large areas. If only finishing the slopes of the front door from the inside, then there will be a need for additional manipulations. The fact is that during installation, numerous cracks (joints) appear that need putty with putty.

Drywall slope during installation

• MDF panels.

This should include the laminate. Such products are great for finishing work. The panels are installed very simply, the resulting surface has an excellent decorative look. But there is one drawback, if the width of the opening is greater than the material used, then it becomes necessary to perform docking. Laminate forms less noticeable seams, but they also impair visual perception.

MDF front door trim

• Natural tree.

Of course, making door slopes with natural wood is a rather expensive procedure. But we must not forget that a very beautiful coating is obtained, which has unlimited durability. If necessary, restoration work can be carried out. All activities must be carried out in compliance with numerous technological nuances.

Door frames made of natural wood

• chipboard materials.

This option allows you to veneer even very wide openings. Many mistakenly perceive chipboard as an exclusively material for the manufacture of furniture. In fact, for facing areas adjacent to the front door, thinner sheets are used, which have very impressive characteristics.

Finishing the slope of the laminated chipboard

Advice! Currently, there is a large selection of chipboard. For installation, sheets are used that have a thickness of 6 to 10 mm.

Plastic slopes are an option that is more suitable for working with window openings. The fact is that this type of product often comes into disharmony with the material of the input structures. Certainly, modern technologies allow you to choose the right solution, but it is not always possible to do this.

Door slopes made of PVC panels

• Decorative stone and brick.

There is an opinion that this method is rapidly going out of fashion. In fact, the situation is not so sad. Such material allows you to get an individual and reliable surface. It should be borne in mind that the laying of parts will require a large number time. Many masters pay attention that in the future it will be very difficult to complete the finishing work of the walls. After all, for work you will have to use a limited set of options. So, for example, cladding with any kind of panels will be difficult - it is difficult to fit them under the masonry.

Decoration of the front door opening with decorative stone

• Extras.

This material is most suitable for mounting slopes on interior doors. A box of such designs suggests the use of this option. Therefore, door manufacturers are developing a whole line of extensions that are completely identical in color and texture to the door leaf.

Slope from extensions

Preparatory activities

Installation of slopes on the front door begins with preparation. It is important to perform the work qualitatively in order to avoid correcting possible problems.

• The surface is cleared of the existing remnants of the old layer. If the coating crumbles, then it should be completely removed to the base.
• If a new structure was installed, then excess foam remains. It is cut with a clerical knife. It is impossible to allow the removal of excess.
• All joints and gaps between the box and the wall are smeared. Sealing is carried out around the entire perimeter.
• Sections of the walls are finished with plaster. If sheet and panel materials are installed, then the slopes of the front door are sealed without carefully leveling the surface.
• Be sure to treat with antiseptic and priming compounds. This will help prevent mold and mildew. It will also improve adhesion if the door slopes are finished with decorative mixtures after installing the front door.
• A complete absence of areas that may contain small cracks should be achieved. It is these, sometimes imperceptible defects, that are the source of drafts and unpleasant howls when it comes to entrance openings.

Stages of preparing the slopes of the front door for finishing

Slopes on the door are mounted only after full preparation.

Technological aspects of working with some materials

Each of the materials has its own characteristics and technological aspects, which should be considered in more detail.

Work with plaster: simple and decorative (textured)

Slopes on the front door using ordinary plaster are made as follows:

1. The right amount of the mixture is prepared, which should be enough for 35-40 minutes of work. If there are surpluses, they will quickly lose their properties.
2. The solution should be applied in layers that are equal to 1-1.5 centimeters. It is taken into account that more than two layers require reinforcement with a reinforcing mesh.
3. To obtain a flat surface, beacons are installed. They are fixed on a small amount of plasters.
4. Experience should be realistically assessed. If it is not enough, then a wooden lath is laid along the outer edge around the entire perimeter. It should protrude to the width of the applied layer. That is, it will serve as a guideline in order to prevent distortion.
5. After drying, beacons are removed, which leave behind small defects. They are removed with a newly prepared solution. When removing rails, care must be taken. Corners can be reinforced with perforated corners.

Plastering door slopes requires certain skills

After the surface has completely dried, the slopes for the entrance doors are trimmed with decorative materials. It can be paint, wallpaper. But decorative plaster (textured putty) will look much more interesting. It is applied after the primer:

• The decorative mixture is laid on the surface.
• With the help of various devices, a relief is formed. If a decorative mortar is used, then the coating is obtained by proper spreading.
• In the future, depending on the material used, paint, varnish or waxing is carried out.

As such, stucco can still be a great solution for finishing slopes, especially if you're doing a simple renovation or interior upgrade.

Drywall: installation on putty

How to make slopes of the front door using plasterboard plates? The work is carried out according to the following principle:

1. Putty will be used as a fixing material. She's perfect for this job.
2. The process begins with a careful measurement of the opening. All available options must be cleared. Based on them, a diagram of each part is built. It should be borne in mind that the entrance doors have bevelled openings. This is an important nuance.
3. Drywall is cut into pieces. For this, a construction knife is used, with which sheets are cut. Of course, the edges are very uneven, they will have to be sealed with putty.

Cutting drywall sheets

• All elements are tried on in their place.

On a note! It is important to remember that the horizontal element is superimposed on two vertical parts. Its thickness is subtracted from the dimensions of the racks.

Installation of drywall on putty

How to close the joints and cracks that have appeared? Indeed, when fragments of plasterboard are installed on the front door with their own hands, then finishing measures are necessary. They lie in the fact that the corners are formed using perforated overlays, and the surface is covered with a layer of putty.

The installation of gypsum boards differs from plastering in that the base is formed much faster. The job does not require special skills.

MDF panels: fastening to the crate

Finishing the slopes with MDF panels is carried out on the crate. This method is preferred for situations where mounting seam more than 4 cm.

The product should be installed using the following technology:

1. Mounted around the entire perimeter of the opening wooden beam. Parts are stacked horizontally. Fixation is carried out on dowels.
2. It is advisable to treat the planks with an antiseptic before installation.
3. The resulting cells are filled with insulation.
4. All areas are measured. Panels are cut out. They are put into place.
5. Fastening takes place on self-tapping screws, which are screwed into the very edges. They will be covered with decorative corners.
6. Thus, all elements are fixed on the frame.

Sheathing slopes MDF: doorway before and after finishing

Chipboard: installation on vertical racks

Do-it-yourself door slopes using chipboard are not the best solution. But with proper installation, the coating will be durable.

1. The whole process almost completely repeats the work with MDF panels. The difference is that the wooden beam is installed vertically. That is, you need to get two racks that are fixed at each edge.
2. For work, LDPS is used, which is most suitable in thickness. After taking the dimensions, the parts are sawn.
3. In order not to repair the material due to water ingress, all open ends are coated with sealant.
4. The elements are fixed through pre-drilled holes, which at the initial depth should be slightly larger than the diameter of the cap. This allows you to drown the screws so as not to damage front side. All holes are covered with special wax or sealed with overlays.
5. All corners and joints are closed with decorative corners.

This method is convenient if the slopes of interior doors are faced, which are less susceptible to moisture.

PVC panels: adhesive mount

This material is rarely used for such work. Also, many people mistakenly believe that you can give preference to the cheapest options. In fact, such a choice leads to the fact that the coating begins to deteriorate immediately after installation: defects appear, color changes.

Most often, plastic panels are fixed with glue:

1. Preparatory work is being carried out carefully. The differences should not be more than 2 mm per 1 m.
2. The panels are cut according to the dimensions taken from the areas to be lined.
3. It should be borne in mind that the fastening is carried out on glue. Therefore, before installing the slopes on the door with your own hands, all surfaces must be pre-treated. A primer is used for the walls, and the plastic is slightly sanded from the inside with sandpaper. Such procedures will increase adhesion.
4. Glue is applied with a snake. It is important to consider that excess mixture is removed immediately, otherwise the surface may be damaged, which will lead to repair or replacement of parts.
5. The elements are pressed against the base, but are not held, but immediately come off. After waiting a few minutes, they are finally installed.
6. Now it remains only to fix the decorative fragments.

The easiest and fastest way PVC installations panels on slopes - this is an adhesive fastening

Modern versions of PVC have sufficient strength and beauty. Alternatively, sandwich panels are used.

Decorative stone and brick (tile): the main thing is to draw up a diagram

How to make slopes on doors from artificial stone or similar materials? The procedure is:

1. It all starts with drawing up a diagram. It should reflect the actual position of the elements. If brick laying can be drawn on paper, then more work will have to be done with the stone.
2. Initially, the surface is marked. It is immediately taken into account whether the details will lie only inside the opening or frame the outer part.
3. Detailing is done on the floor. It should be detailed enough.
4. Now start lining. The stone is fixed with glue or special blend. It is important to consider whether suture or seamless technology will be used.
5. After laying, if the surface is not protected, it is varnished.

Thus, slopes for doors can be made of various materials. Each option is selected individually.

Finishing the slopes of the front door from the inside with your own hands: installation options (photo, video)

Finishing the slopes of the front door requires a special approach. Used for work different materials, some of them are suitable for independent use

Slopes for entrance doors

With carelessly made slopes, even the most expensive and luxurious front doors will look unattractive. Why do we need slopes for entrance doors? First of all, they are used as a beautiful frame, a means of complementing and highlighting the main element - that is, the door itself. In order for you to be able to decide what material to make slopes from, it is necessary, first of all, to pay attention to the design of the door structure itself, its style and color. After all, it is important that the slopes fit not only the design of the door, but also the overall design of the room.

Slopes for entrance doors

We also note that the described elements perform not only aesthetic functions - they are also an insulating layer, because they close the joints between the structure and the walls.

Basic materials for the manufacture of slopes

To create slopes, you can use the most various materials, although, as an option, you can bring the already existing slopes into a “divine form”.

Option one. Plaster

If the door structure is strong and reliable, but does not look very presentable, reinforce the corners and level the slopes using plaster. Tellingly, this is often done not only by staircase but also in the hallway.

Note! The plastered slopes will look pretty neat - if you wish, you can additionally paint them in the color of the room or door trim.

Option two. Drywall

It is advisable to use this material if your slopes turned out to be wide due to the rather large thickness of the walls. Thanks to the use of drywall, your walls will become warmer, and all existing joints will be securely closed. In addition, the slopes, again, will look very neat.

If you want, you can subsequently paint the drywall or, alternatively, paste over with wallpaper. One of the main advantages of the material is that its installation does not require laborious work to level the surface.

Option three. natural wood

If the wood is suitable for door trim, then you can use it for slopes. It is no secret that wood has always enjoyed considerable popularity and, apparently, will never go out of fashion. The material fits perfectly into almost any interior design, and if necessary, you can easily change the tint of the material using folk / modern means.

In addition, wood can serve you for many years, while retaining all its decorative and operational properties. Although, in a pinch, you can always paint it to match the color of the hallway.

Option four. Laminated lining

Such lining, made on the basis of chipboard, can be an excellent alternative to natural wood.

Due to the fact that this material is produced in the most different colors and can imitate the texture of various tree species, you can always choose the most suitable option under the decoration of the hallway. However, it is highly undesirable to use lining when finishing external slopes, since it will simply quickly become unusable there.

Option five. PVC panels

The next material through which they can get off slopes for entrance doors, are ready-made PVC panels. This material is made in a variety of colors, and the dimensions of the panels can also be different. The production and sale of this kind of panels are carried out by specialized companies, where specialists work who are also engaged in their (panels) installation.

This finish of the slopes looks attractive and respectable. The service life of PVC panels is quite long, but it is still desirable to mount them from the side of the hallway, and on the reverse side - options No1 or No2 (they are described above).

Note! If you are completely confident in yourself, you can finish the slopes with finished elements with your own hands.

Although it is worth noting that there is another option for using polymeric materials for slopes - in this case we are talking about plastic lining. It also comes in a variety of colors, so you can easily choose the most suitable option for decorating the hallway.

Option six. Chipboard panels

Yes, they are also widely used in the design of slopes. But, as a rule, only for thick walls. Although in fairness, we note that this option has not been very popular in recent years due to the emergence of a huge number of more modern materials capable of replacing chipboard elements that are so difficult to install.

In any case, if you have a panel lying around suitable sizes, you can easily arrange door slopes from the inside with it.

Note! There are other materials used in the design of slopes (for example, laminate, installation instructions for which will be given at the end of the article), but only the most common options were considered above.

What is required for the design of slopes on their own?

Before proceeding directly to work, you must prepare everything necessary materials and equipment. So, if we are talking about plaster, then you should prepare:

• finishing putty;
• sandpaper (large and medium);
• primer;
• sickle tape, self-tapping screws and a mounting knife (in case drywall sheets are used for finishing);
• the plaster itself;
• iron perforated corner (it will be required to align the corners);
• level;
• spatulas of different sizes;
• plumb;
• rule (it is important that it be shortened);
• electric drill with a special nozzle-mixer;
• container of suitable size for mixing.

If panel materials are used for finishing, then the list of everything you need will look a little different:

• the panels themselves of the material of your choice, additional elements required for their installation;
• a hammer;
• platbands, decorative corners;
• timber 2x3 or 1.5x3 centimeters (in case slopes for entrance doors will be finished with clapboard);
• screwdriver;
• dowels;
• electric jigsaw (as an option - you can use a simple hacksaw);
• perforator (in case of walls made of concrete);
• measurement tools;
• self-tapping screws with which the panels will be attached.

When all the required equipment and materials are ready, you can proceed to preparatory work and directly finishing. Let's consider in more detail each of the possible options.

How to properly trim slopes for entrance doors - detailed step-by-step instructions

First, let's get acquainted with some features of the finishing process.

• Most of the materials described above are installed using the same technology.
• Some technologies are quite simple, and therefore the work can be done independently.
• The rest, on the contrary, can only be used if you have certain skills in working with materials and equipment.

In any case, the finishing work itself should begin only after the installation of the door structure and the sealing of all joints between it and the wall. We also add that the previous coating should be removed from the slopes in advance, as well as peeling areas should be repaired. After carrying out all these activities, you can proceed directly to the finish using one of the technologies presented below.

Option one. Plastering door frames

If you decide to use a plaster mixture for finishing, then proceed in accordance with the instructions.

Step one. First, prime the previously cleaned surfaces (if possible, then in two layers, but the second layer should be applied only after the first one has completely dried).

step two. After that, determine how even the slope angles are. In case of deviations from the norm, be sure to take this moment into account when installing the reinforcing corners. With the help of the latter, you can easily align corners that deviate slightly from the vertical.

Step Three. Next, using a level and a plumb line, set the perforated metal corners at the corners. Ideally, they should immediately be attached to the finishing putty (the latter can be purchased already in ready-made). Apply it, using a spatula, to the corners of the slopes - the mixture is necessary not only for fixing the corners, but also for leveling the slopes horizontally / vertically. Remove excess solution that has come through the perforation immediately using the same spatula. When everything is perfectly smooth, you can rest for a while - the putty should dry completely.

Step Four. In the case of uneven slopes, before installing the leveling corners, it is recommended to set the direction from the door jamb by fixing a plasterboard strip about 0.8-1 cm wide along it. To attach this material to the surface, use putty. If the putty you use is gypsum, it will not take very long to dry completely.

Step five. The perforated corner and the edge of the drywall strip are, in this case, the points that you must connect with putty and level with the plaster mixture.

Step Six. We continue to finish the slopes for the entrance doors. When the elements that correct the walls are dry, spread the putty (according to the manufacturer's instructions) to end up with a paste-like mixture.

step seven. Using a trowel, throw the resulting mixture onto the wall, moving up from the floor. After throwing the right amount (about 100 centimeters high), level the putty using a short rule. As a kind of beacons, a metal corner and a previously fixed plasterboard strip will serve.

Step eight. Throw the mixture on the second section, level it, and then move all the way to the top in the same way.

Step nine. With puttying the upper surface of the opening, certain difficulties may arise. So, for applying putty there, you will have to use a wide spatula, and for leveling - all the same short rule. After that, putty the wall above the opening, then close with a mixture upper part perforated corner.

Step ten. Wait until the puttied slopes are completely dry. The drying time depends on the composition, as well as on the thickness of the leveling layer.

Step Eleven. When the layer dries, check how good the surface is. If there are minor defects, clean or chip them. After that, bring the slopes to the limit evenness, using the finishing putty for this.

Step twelve. At the end when finishing layer dry, cover it with a primer.

The resulting slopes can be wallpapered, painted or, alternatively, finished with decorative plaster.

Option two. We use plasterboard for finishing

This material is simpler and easier to work with than the plaster described above. However, you still have to use the finishing putty - in this case it will serve as an adhesive for GKL sheets; although instead of it, it is better to give preference to special gypsum adhesives, which are designed to work with just this material.

In the case of limited space, drywall sheets are perfect option for finishing slopes. The algorithm of actions in this case should be as follows.

Step one. First of all, separately measure each of the slopes.

step two. Transfer the received numbers to the sheets of material, then, working on the markup, open the elements for subsequent fastening to the walls.

Step Three. Install drywall sheets from the bottom of the opening. First, apply several “hills” of glue on the first sheet, as in the image, then press the element firmly to the desired location and additionally fix it with pre-prepared supports.

Step Four. Similarly, finish the side slopes with drywall parts, not forgetting to check each of them for level. For fixing to the walls, you can use driven dowels, having previously made narrow through holes under them with a perforator.

Step five. Just as in the case of using plaster, close the corners with iron corners, using the same putty for fixing.

Step Six. Lubricate all joints with putty, carefully align and, when it dries, clean it thoroughly so that the finished slopes for entrance doors looked most attractive.

step seven. To obtain a perfectly even surface, apply a millimeter layer of finishing putty mixture. So you will finally mask all the defects and holes for the dowels.

Step eight. When the mixture has completely hardened, you can sand the surfaces with fine sandpaper (if required) and, finally, proceed to decorative design. You can use for this, again, paint, decorative plaster or high-quality wallpaper.

Note! There is another way to fix drywall - it is advisable in cases where, when leveling the slopes, it is necessary to close a considerable thickness of the wall.

• Fasten metal corners or wooden bars to the slope, thereby forming a crate in order to give the wall the desired direction. The main advantage of this method is that between the elements of the crate it will be possible to additionally lay thermal insulation material.
• close the crate drywall sheets, using for fixing with self-tapping screws. Everything else is not much different from the technology described above.

Option three. We use lining or panels

If you intend to use panels made of rigid materials in your work (this includes many types of lining, MDF, chipboard, etc.), then you should know that they are all attached using almost the same technology. The advantage of this method is that even the most serious irregularities can be hidden with such panels.

As for the specific algorithm of actions, in this case it will look something like this.

Step one. First, prime the slopes, mark the places where the bars or iron profiles will be attached. The step between them should be approximately 30-40 centimeters (if they are mounted across the slopes). In our example, a lining is used, mounted parallel to the box. If a transverse arrangement is required, fasten the crate along the jamb. If the surface is wide enough, you can use not 2, but 3-4 strips at once.

step two. The image shows another option - with the installation of lining parallel to the door leaf.

Step Three. You can lay heat-insulating material (polystyrene, mineral wool, etc.) between the lathing slats.

Step Four. Install the panels of the selected material on top of the finished batten.

Step five. For installation of laminated / plastic lining, use the metal fasteners shown in the image.

Step Six. To fasten large panels, use self-tapping screws, sinking the latter by 0.15-0.2 centimeters. To close up the formed holes, you can use putty.

step seven. At the end, install decorative corners. They must match the color of the cladding. Glue the corners on the horizontal as well as the outer vertical corners; finally, at the joints of the finishing material and the door frame itself.

Rules for creating vinyl slopes

Vinyl panels are rightfully considered one of the most modern materials that can be used for finishing slopes. They are sold in almost all specialized companies involved in the production and installation of this material. In the case of a non-standard form of slopes, the panels can be made to order, having previously measured the dimensions.

Finishing can imitate various natural materials, so in any case you will choose the most suitable option for yourself, regardless of the design of the door and the hallway itself.

Note! The main advantage of such panels is that they are quickly installed, and there is little debris left after completion of work. Yes, and this kind of finish looks extremely attractive, neat and stylish.

This material is fastened with a universal adhesive that can reliably connect materials of different properties (for example, brick and lining, concrete and wood, plaster and vinyl). In a word, everything that can be used in the course of finishing and construction works. Still, as an option, slopes for entrance doors can be finished with vinyl using polyurethane foam.

The adhesive should be applied to the inner surface of each panel, and then pressed against the slopes. In this case, no holes need to be drilled in the walls or cladding, which can also be attributed to the undeniable advantages of this technology.

Using laminate is a worthy alternative

Laminate is widely used as flooring, it is easy to work with and comes in a variety of colors. Who does not know, laminate is an MDF panel covered with a special decorative layer. Why is this material so popular? This is because it has many important advantages.

1. It is inexpensive and can be used for different surfaces, including for slopes.
2. Some of its varieties are moisture resistant.
3. The material looks attractive, and it goes well with other finishing materials.
4. Laminate has excellent wear resistance. It is not erased for a long time, in addition, it can withstand not very strong blows.
5. Finally, the material is produced different types, textures and colors. Therefore, you will definitely choose the most suitable option for yourself.

Note! The service life of slopes can reach 10 or even 15 years, which, you see, is not so short.

Sheathing slopes with laminate can be done by one of several possible ways. Let's get acquainted in more detail with each of them.

1. For glue. In this case, liquid nails or similar formulations may be used. However, the surfaces must first be leveled (using plaster or plasterboard sheets).
2. With the help of a framework. The most time-consuming method, which, nevertheless, allows you to get extremely even slopes without resorting to preparatory leveling of the walls. Also, this method makes it possible to lay a layer of thermal insulation material, which will help save heat in the apartment.
3. For mounting foam. The simplest technology that does not require preliminary alignment. All defects will be eliminated after the mounting foam swells.

As for the laying process itself, it - regardless of the specific method chosen - should begin with surface preparation. In our example, the laminate will be attached to the adhesive. The algorithm of necessary actions is given below.

Step one. First fill all the gaps and apply a layer of plaster. Do all this on a plaster mesh. Later, when the plaster is completely dry, prime the slopes to provide additional protection.

step two. Here begins the most important stage of work, so approach the matter with the utmost responsibility. You need to mark up and cut the laminate. Start at the top, then move on to the sides. We recommend cutting the material with an electric jigsaw, although in the absence of one, a regular hacksaw may well be suitable.

Step Three. Before gluing, install mounting spacers - a kind of border, thanks to which the material will not move.

Step Four. Take the first lamella, put it on the upper slope, and then open the door - the latter should not catch it. Then apply foam to the inner surface of the laminate, press it against the slope and fix it with masking tape (you can remove the latter only after complete drying). Too much foam should not be applied, because an excessive amount of foam after swelling can lead to displacement of the element.

Step five. Install the sidewalls in the same way, regularly using the building level.

Step Six. Having laid out all the slopes, wait for the mounting foam to dry completely and proceed to the final stage of work. Cut off excess foam, close the openings with plaster. But this is not the end yet - slopes for entrance doors looked really attractive, seal the openings with a corner of a suitable color.

That's all, now you know about the most popular ways to finish the door slope. We hope the article was really useful for you.

Good luck in your work and, according to tradition, warm winters to you!

Options for finishing the external and internal slopes of the front door

Having installed and admired the front door, it becomes clear that the work is not over yet. The next step will be the finishing of the slopes, which perform aesthetic and practical functions. For their arrangement, you can use different materials, adhere to different styles.

External slopes of the entrance door

Having installed the door, it is necessary to hermetically fill the joints between the door frame and the opening in the wall. The easiest way is to use mounting foam. After it dries, the protruding excess is removed and the tightness is checked.

Having closed the door, a lit lighter is carried along the perimeter of the opening - in places where the flame moves, it is necessary to re-foam.

Advice. Certainly to exclude blowing will allow sealing the seams with adhesive cement mortar. It cannot be replaced with putty or plaster.

After the mortar or mounting foam has hardened, door trims can be fixed. They hide the opening from the eyes, protect door locks and burglary pins. We will tell you how to choose a reliable lock in a separate review. Cash must match the front door in design and color. Fasteners are made with special brackets.

In some cases, the front door is made with a certain recess in the wall - a full-fledged external slope is formed. It is customary to seal it with cement, having previously cleaned the surface of dust and dirt.

Finishing can be absolutely anything, but it must be combined with the door. If the latter goes into a heated entrance, you can use laminate or plastic. But the most optimal and cost-effective option is to paint the surfaces brought to zero.

Internal slopes of the entrance door

Starting to finish the slopes of the front door indoors, it is necessary to choose the most suitable material. There are a lot of options on the market:

Wood is the classic and most popular of the materials. It can harmoniously fit into any interior, adding grace to it. But such surfaces under the influence of aggressive factors can quickly lose their appearance, requiring restoration work.

The cheapest and easiest way is to apply a layer of plaster. In the future, it can be painted in any of the colors you like. Over time, when the opportunity and desire arise, the slopes are easily covered with other, more interesting material.

In spite of wide application plastic for finishing window openings, door slopes are rarely closed to them. This method is used in cases where a PVC door is installed.

You can fix serious irregularities near the door with drywall. This method eliminates the need to apply numerous layers of dry mix.

Finishing slopes with wood or plastic

To complete the work you will need:

• MDF or laminate, PVC panels
• Mounting foam
• Rule and bubble level
• Wooden slats
• fasteners
• Tools

Advice. The most optimal solution is to use an MDF board. But it does not always fit in width into a thin opening. An alternative can be a conventional laminate.

The doorway is once again checked for sealing of the seams and the areas in which air leakage is observed are foamed. Then the excess foam is cut off, the surface is cleaned and covered with primers.

The next question to be solved is the shape of the slopes. Wooden panels can be placed perpendicular to the door or at a certain angle. The shape is determined by rails mounted on both sides. Making slopes with the letter “L”, the rail near the door should be wider, near the corner - thinner. Everyone chooses the proportions individually.

Having fixed the supporting rails to the wall with dowel-nails, the upper slope is first mounted, then the side ones. The panels can be put on special glue or screwed with screws, covering the holes with decorative caps. The corners are neatly hidden by decorative plastic corners.

Exactly according to the same principle, slopes are finished with PVC panels. The only difference is that they are planted exclusively on adhesives so that the surface remains aesthetic.

Finishing slopes with plastering

Plastering is the strongest and most durable finish. For work you will need:

• Rule and bubble level
• Sandpaper
• Sand, cement
• Putty mixes
• Primer
• Beacons
• Master OK
• masking tape

Objects and surfaces that can get dirty are covered with foil or covered with masking tape. First of all, guide beacons are set. They are planted on a thick solution of cement or gypsum, plastered on the wall. If there are large potholes in the wall, the solution will have to be kneaded more.

Advice. The wall is pre-coated with priming compounds to prevent the appearance of fungus on it and improve adhesion to the solution.

Having diluted a solution of sand and cement in a ratio of 4 to 1, all potholes are thrown. The first layer of plaster is applied. When the wall cools down, a reinforcing mesh is applied and work continues. Having sketched the mixture, the slope is aligned with the beacons by the rule.

When all surfaces are plastered and dry, a layer of finishing putty is applied. After it hardens, the surface is brought to zero with fine sandpaper, pasted over with wallpaper or painted.

Finishing the slope with drywall

• Drywall
• Adhesive mixture
• Stationery knife
• Level and rule
• Putty
• Metal corner

Drywall finishing is done in one of two ways: on wooden slats or glue. The second option is used much more often.

First, the wall is primed to improve adhesion with glue and prevent fungus from appearing. Pieces of the required width are cut out of drywall. In total, three strips are required: two on the sides and one on top.

The next step is to mix the adhesive solution according to the instructions on the package. Having applied it to the back side of the cut strip, it is applied to the wall and leveled.

When the glue dries, the excess material that comes out is carefully cut off. The entire surface and corners are puttied and rubbed with fine sandpaper.

Finishing the slopes of the front door is a simple, but very responsible task. The chosen material for work is an individual decision. It is important that they harmoniously frame and decorate the doorway, giving completeness to the finish.

We make slopes for the front door: the choice of material and the installation procedure with your own hands

Before proceeding with the finishing of the slopes near the front door, it is necessary to solve two questions: what material should they be made of and how to organize the work?

In order to quickly and without much expense to tidy up the doorway, you can put plastic slopes with your own hands. These structural elements are easy to handle, and therefore even a beginner can cope with the task. Let's look at the advantages of such a finish and how to properly install plastic slopes on your own.

Plastic slopes - a simple and inexpensive way to trim a doorway

Material Features

Plastic slopes - no less popular finish doorways than drywall or MDF. Especially good in decorative and functional terms are slopes from sandwich panels that you can make yourself. In general, ordinary PVC panels can be used for installation, as a more budget option. However, due to the fact that in the doorway it is often necessary to install a layer for insulation and sealing gaps, it is better to use various models sandwich panels. They are a material consisting of several layers: side PVC linings and a layer between them made of insulation, most often ordinary polyurethane foam.

Both conventional and insulated plastic panels can be used to finish the slopes.

Installation of slopes from sandwich panels has a number of advantages:

• Ease. The material has a low weight, which allows you to install it, saving on fasteners. In addition, their installation does not weigh down the opening itself.
• Availability. You can buy such overlays for slopes in almost any hardware store.
• Range. Samples are available, different in color, texture, haze, size and content.
• Ease of processing. Cutting PVC is very easy, it is especially good to use a jigsaw.
• Easy installation. To make the finish of the sandwich panels with your own hands, you can do with mounting foam or liquid nails.
• Price. Compared to other materials, the price of plastic remains low.
• Thermal insulation. Sandwich panels, due to their filling, allow you to install a barrier to cold and drafts without the use of additional materials.
• Simple care. In order to further clean the surface, it is enough to wipe the PVC surface with a damp cloth.
• Durability. Such slopes will last a very long time, as they resist shock and abrasion well, are not afraid of water and are very resistant to ultraviolet radiation.

Lightness and accessibility are the main advantages of plastic panels as a finishing material.

Pay attention to the quality of the material and the reputation of the manufacturer, not all plastic has the above properties.

Finishing methods

In order to make plastic slopes with your own hands, you need to develop a design project in advance. This is easy to do, just choose the right PVC and choose the way to place conventional or sandwich panels.

Usually, a simple white material is used to finish the slopes with plastic with their own hands, since this is essentially a neutral option, or a beige color. For wooden doors it is also important to select material in the appropriate color and with a similar wood pattern. Thanks to the range of modern finishing materials, this is not a big problem.

There are several ways to install plastic slopes. Finishing might look like:

• Direct overlays. This is the simplest option. In this case, you only need to select PVC pieces that are suitable in size and fix them vertically on the sides and horizontally along and above in the opening.
• Horizontal arrangement. This method is suitable for those cases when pieces of plastic remain after the repair. They are laid on a frame across the wall, masking the joints as much as possible.
• Lamels. If you want to highlight the slopes, then try this option with your own hands. To begin with, a frame is being built, and then plastic is put on the rails, located across, as in the previous version. In this case, it is better to use a relief material, like siding.

Options for finishing door slopes with plastic

Surface preparation

Making good PVC slopes with your own hands is quite simple. To do this, it is not even necessary to display a perfectly even perimeter of the opening.

Before you start making plastic slopes, you need to make sure that the surface quality is up to standard. In apartments and private houses common problem there is the formation of gaps in the opening at the points of attachment of the slopes, which lead to the appearance of drafts and freezing sections of the wall. In order to prevent this from happening, you should first check the opening for cracks and close up all the flaws. For this, mounting foam, sealant or plaster is used. Additionally, it is recommended to lay a layer of insulation on the sides to improve thermal insulation.

Before proceeding with the finishing of the slopes, it is necessary to close up all the cracks and, if necessary, insulate the opening

It is also important to prevent the formation of mold and mildew on the wall. To do this, the work area is treated with antiseptic impregnation. If you plan to pre-level the slopes, you also need to prime the surface. Then the places with the most noticeable flaws are finished with putty. Particular attention should be paid to the corners, in particular the outer ones. For the convenience of removing them, use a sickle and special profiles. Before starting the laying of plastic, you need to make sure that there are no loose areas and construction debris left on the slopes.

Mounting technology

Installation of plastic slopes can be done by hand in several variations. To begin with, you should consider the simplest and most advantageous option, namely, slopes from ready-made sandwich panels. It is best if one of their edges has a ledge with a corner, which will allow you to simultaneously fix the finish on the wall itself from the outer corner and bring out the smooth contours of the opening.

The easiest way is to mount on foam. To do this, you need to attach the panels cut to the width and length of the opening to the place where you are going to mount them. Level and install spacers. Then you need to apply a small amount of foam into the gap. After the mounting foam has dried, the finish will be securely fixed in place. This can also be done in advance if the PVC trim blocks access to the back of the plank.

Another installation of plastic slopes on the door with your own hands involves the use of profiles. You can take the same PVC material or use aluminum as for drywall. First of all, you need to make a frame around the perimeter of the opening. After installing it with your own hands, front finishing can be performed. The plastic is screwed with self-tapping screws, and then the fastening points along the edges are closed with a PVC corner, planted on glue.

For additional insulation under plastic, you can lay mineral wool or isolon.

Thanks to plastic slopes it is possible to equip a full-fledged design of the doorway in a short time. This is a great finish for budget repair in home.