How to make a sofa out of foam rubber with your own hands. Drawings and schemes of sofas. How many sofas, beautiful and different ...

25.05.2020

For a summer residence, a bath or a kitchen, people often buy furniture in a store. But you can do it yourself and at the same time spend much less than purchasing items in specialized salons. How to make a sofa with your own hands? What materials and tools are needed for this? In order to answer these questions, you must first accurately determine the variant of such a sofa.

A do-it-yourself sofa outperforms a purchased one not only in price, but also in design.

It can be of different configuration, which depends on where it is planned to be installed:

simple design in the form of a single block;
corner version of two small parts;
multi-element sofa, the main details of which allow you to assemble several types of similar furniture.

You can make the first two options yourself: they are simple and require a minimum of material.

The process of making a sofa with your own hands

sofa project.

First you need to select a drawing of the future subject from the relevant literature. Then bind the sofa to the place where it is going to be installed. To do this, measure the length and width of the allotted corner, and if the dimensions on the drawing are slightly different, then they correct them and draw a sketch with the required dimensions on a piece of drawing paper.

Now you need to collect the necessary materials. For these purposes, you can use a bar, the trimmings of which often remain during the construction of various utility rooms in the country. If they are not there, then the necessary material is bought on the construction market.

How to make a sofa with your own hands? To do this, you need to purchase:

foam rubber - it is sold in furniture stores;
for the manufacture of a cover and pillows - a zipper;
to cover the surface of an object, they buy tapestry-type material;
in the construction market they acquire a mesh and a corner made of metal.

After that, work begins on assembling the base (frame). A bar is used for it. Its dimensions can be 700 x 2100 mm. Small tree trimmings will go to the legs - you will need four of them. This is done in this way:

Sofa frame assembly diagram.

in size from a sketch from a bar, frame parts are cut with a hand saw - two long slats (they should be equal to the length of the future sofa) and 2 short ones (in width);
less thick material is used for legs and handles - 4 legs and two handles are needed;
knock down the frame with nails or use long screws;
then the remaining elements (legs and handles) are attached to it;
transverse planks are cut from the boards - they will need several pieces, the main thing is that they go inside the frame;
they are connected to the base with the help of metal corners and screws, and an armored mesh is installed on the frame, which is fixed to the base with brackets;
now parts for the back are cut from squares: two along the length of the sofa and two along the height of the future headboard;
assemble it with screws or welding;
for the back you will need a sheet of plywood or chipboard, which is reinforced with screws or screws.

Base work completed.

Making soft upholstery on the sofa with your own hands

The coating technology includes the following components:

Scheme for the manufacture of a soft seat for a sofa.

two mattresses are cut from the purchased foam rubber, the dimensions of which should be equal to the dimensions of the sofa;
they are sheathed with material, the resulting two covers are connected with a snake;
tapes are made from the same tapestry, with the help of which the mattress is fixed on the base, these connecting elements contain Velcro, and they are nailed to the frame at one end, and at opposite points with the other;
then 3 pillows are made of foam rubber in the same way and covered with covers with snakes;
they are strengthened on the back with tapestry tapes.

On this, the production of this option can be considered complete.

Making a sofa from ready-made shields

If a person has no experience working with wood or metal, you can try the method below to make this household item from a material that is usually thrown away. These are old doors. Their doors can make a great sofa. Together with them you will need the following details:

Foam rubber will be needed for upholstery of the sofa and pillows.

foam rubber - you need to buy it in the store;
covering fabric (tapestry);
leftovers from wooden beam or hemp;
metal staples that are purchased on the construction market.

The basis of this design option and the back are 2 sashes from old door from a tree that has served its time. Its surface must be durable, otherwise the idea will not work. The door is cleaned of dirt and scraped off old paint. Then the surface of the future base and back is carefully polished with emery. If there are cracks or indentations on it, then they must be repaired with a priming paste for wood. The door leaves are sanded again and then covered with several layers of paint. The color of the coating is selected according to the design of the room where the sofa is supposed to be installed.

If possible, then in the construction market or in a specialized store they buy veneer and glue and finish the surfaces using a heated iron. In this case, the finished design will look more presentable.

Scheme of assembling a sofa from shields: 1 - sidewall; 2 - additional pillow; 3 - pillow-back; 4 - retractable mattress; 5 - support bar; 6 - stool-stand; 7 - base box.

One of the door leaves is installed on the stumps or the remains of the timber with the help of construction nails. and the second part is attached with metal brackets at the right angle - the base is ready. Now we need to make a mattress. It is cut out according to the size of the resulting frame and sheathed with material (tapestry). If it is not possible to purchase a new fabric, you can get by with coarse calico or matting, and cover it with material with the desired color on top.

The next step is the manufacture of foam rubber pillows, which was described above.

The made mattress is laid on the base, and pillows are placed on the back. All this is strengthened with tapes and nails. Such a sofa can be installed in the country or in the bath. It will fit well into the interior of the kitchen in country house or verandas suburban area.

Making a corner sofa

If a person makes such a design for the first time, then you need to choose the simplest option. They bind it to the room and draw a sketch with all sizes. For simplicity, you can refuse spiked joints and the use of expensive materials in the process of creating a structure. To connect individual parts, it is best to use screws. All wooden parts must be sanded before assembly. First, with the help of a jigsaw, all the details of the structure are cut out of chipboard. Start the assembly from the left side of the sofa corner:

armrests are assembled from separate parts, they are connected with screws;
the frame of the left side is made of bars with a section of 5 x 6 cm and reinforced with transverse rails;
a chipboard sheet (thickness 14-18 mm) is attached to the base, and then plywood must be attached to the back frame with screws.

Assembling the right side of the structure:

Assembly diagram corner sofa.

its bottom should be made in the form of a box, whose base is assembled from bars, and then sheathed with plywood;
cut out the side racks and attach to the main structure;
if you plan to install a sofa in the middle of the room, then the back part must be sheathed with chipboard sheets;
holes are drilled and a microlift is installed using screws with furniture caps.

The next stage of work is the manufacture of foam mattresses. Their thickness should be equal to 10 cm. Sheets of material must be glued to the base.

Start upholstery construction. For all surfaces, it is necessary to make patterns from cardboard, fabric will be cut on them. This is done upside down. Leave an allowance of 10-12 mm on the seams. If the material crumbles, then they are made even more. For recesses in the skin, holes are made in the slabs of the structure. Loops of synthetic cord are installed there, and they are sewn to the main upholstery. The fabric is shot to the foam rubber with a stapler. Once covered with cloth, the item is ready for use.

A similar sofa corner can be placed in the kitchen or in the living room. When using a less expensive upholstery fabric, it can be installed in a country house or a country house.

How to make a corner sofa even easier? Just put two small sofas made using the technology described above at an angle of 90 degrees to each other.

Tools and materials that will be needed in the manufacture of the structure

Basic tools for making a sofa.

Wooden beam.
Stumps and planks.
Boards.
Plywood or fiberboard.
Microlift (for a corner sofa).
Metal squares and corners.
Sheet foam.
Lightning snakes.
Sewing machine.
Textile.
Shutters from doors.
stapler.
Metal staples.
PVA glue.
Paint, primer.
Sandpaper.
Hand saw and jigsaw.
Electric drill with drills.
Construction knife.
Paint brush.
Tape measure and pencil, paper sheet.

The main thing in self-production different types sofas is the creation of a reliable foundation (frame). Therefore, any solid material that can be easily processed at home is used for the frame of the structure. It all depends on the imagination and financial capabilities of the person who decided to independently make such a product.

To achieve a positive result, it is necessary to consider possible options and choose the most suitable sofa for a particular room, and in its manufacture, adhere to the manufacturing technology and all these recommendations.

An important role in the life of every man is played by a home sofa. Do not be ironic about this. A lot of creative plans and ways to implement them were conceived on this piece of home interior.

A good sofa can be bought in a store, today this is not a problem. But does a real home master miss the chance to try his hand at making upholstered furniture?

Financial incentive is another weighty argument in favor of the "couch project". If you calculate the cost of materials needed for work, and compare it with the price tags of furniture stores, then the savings will be very impressive.

In our article, we will consider the implemented options for home-made sofas and give short description their manufacture. In addition, the topic of self-assembly of a corner sofa will be covered, from the drawing to the finishing sheathing.

How many sofas, beautiful and different ...

Having decided to make a sofa with your own hands, it will not be superfluous to get acquainted with ready-made samples of home “sofa” creativity.

We note the main features of this type of furniture, so as not to confuse it with an ordinary bed in the future. Main hallmark the sofa is not a soft bed, but a backrest that you can lean on. The bed does not have this element. Side railings with armrests are another classic element of sofa design.

AT modern models armrests are often abandoned, leaving only the backrest. In some designs, it can be turned on hinges and turned into a mattress.

Photo No. 2 Sofa with a swivel back

Such a system was called "Eurobook". The principle of its operation, as can be seen in photo No. 2, is very simple: a block with a seat on wheels moves forward, and the backrest turns on hinges with a slight movement of the hands and turns into an extra bed. This option can be taken into account by those who decide to make a sofa at home.

No wonder they attract the attention of home furniture makers. These are ready-made solid modules. Of these, you can minimal cost funds and time to build an original lodge. A pallet sofa made in a deliberately rough loft fashion style looks great with a dump truck wheel that doubles as a coffee table.

All you need to assemble this design is a screwdriver and a jigsaw. Having fixed the base pallets in pairs with screws, the sidewalls are attached to them. They are made from the same pallets, cut at the level of "bosses" - thick wooden inserts. This sofa does not have a back. It is replaced by two wide pillows leaning against the wall. A pleasant "softness" of the whole structure is given by two thick foam mattresses.

If you are going to make a simple sofa, try to enlist the help of your spouse. Her sewing machine will save you from having to go to the studio for sewing covers. If your wife does not share your grandiose plans, then buy a construction stapler. With it, you can accurately and quickly complete the upholstery of the frame.

Someone likes wood, and someone cannot live without metal, making everything necessary from it, including a sofa. If your old cast iron bath not yet scrapped, then use original way turning it into a comfortable couch. best material than enamelled cast iron, for the garden patio is not found.

Such an outdoor sofa is not afraid of either snow or rain, regularly bringing respect to its owner from guests and neighbors.

Modellers-constructors do not only models of old ships, tanks and aircraft. Furniture items often fall into the sphere of their attention (photo No. 6).

Why don't we make such a sofa by increasing its miniature layout to the desired size? The idea of this design is simple and rational: the base is made of a profile pipe, to which thick plywood or OSB board is attached.

After practicing assembly techniques on a smaller copy, it will be easier for you to work with a full-length sofa.

If the farm does not have an old tire, then making an original round sofa is not easy. If rubber "shoes" of the tractor are available, you can cover them with fabric and attach a high back. A stand with legs and soft foam cushions give the structure the perfect look.

How to make a corner sofa yourself?

Without a detailed assembly diagram, it is impossible to start this work. The corner sofa consists of several parts, the manufacture and docking of which requires precision. The best fastening material for a beginner is self-tapping screws. Spike connections frame - the level of an experienced carpenter.

So, to assemble a corner sofa, you will need the following materials:

wooden block (section 30x50 mm);
board (25x80 mm);
plywood or chipboard (thickness 12 mm);
plywood (thickness 5 mm);
foam rubber 10 cm thick;
thin foam rubber or batting (for making a lining for the hull skin);
PVA glue for attaching a soft lining;
upholstery fabric.

To work, you will need the following set of tools:

screwdriver;
jigsaw and hacksaw with a miter box;
construction knife for cutting foam rubber;
scissors for cutting furniture fabric;
stapler;
self-tapping screws;
sewing machine.

Before you make a corner sofa yourself, you need to clearly define its layout and once again review all the prepared drawings.

The basis of each block of the corner sofa is a frame made of plywood or chipboard fixed on a bar frame. If the thickness of the plate is large enough (from 16 mm), you can do without a bar. In this case, the self-tapping screws are screwed directly into the ends of the plates, having drilled guide holes of small diameter in them to prevent splitting of the material.

For the rational use of the internal space in blocks No. 1 and No. 2, removable covers can be made. To support them from the inside along the contour of the frame, it is necessary to fix a bar with a section of 2x3 cm, lowering it below the upper cut of the plates by the thickness of the cover (12 mm). In order for the lid to be easily lifted, two holes are drilled in it for fingers.

By design, blocks No. 1 and No. 2 are the same, but we will make block No. 3 with a drawer-seat that increases the useful area of \u200b\u200bthe sofa. This is the simplest option that does not require the installation of transformation mechanisms (retractable or rotary). Them correct installation and adjustment for beginners is a complex process.

We will have a drawer with a lid made of chipboard or thick plywood. It is not difficult to assemble it, but making comfortable folding legs is a problem. They will interfere when pushing the drawer into the sofa body. Instead, we will increase the height of the front plate of the box. It will play the role of a support platform when unfolding the sofa.

For easy pull-out, two wheels from office chairs can be attached to the back of the front panel of the drawer. The body of the wheel will not rest against the bottom of the sofa if a small cut is made in it in advance.

The lid on unit 3 can be made removable to store bed linen.

The dimensions of the seat cushion must be equal to the dimensions of the drawer area. Pulling out the drawer of our corner sofa, we remove the back cushion and put it in place of the mattress.

Further our step-by-step instruction contains a description of the assembly of the backs. For all corner sofa blocks, their design is the same: vertical posts connect three boards. The two lower ones serve to fix the back to the sofa, and the upper one provides rigidity and serves as the basis for attaching the skin.

Having assembled the back frame, it must be sheathed with plywood 5 mm thick in front and behind. All sharp corners are processed with sandpaper so that there are no hooks and irregularities when installing upholstery fabric. Batting or thin foam rubber should be glued to all front and side surfaces to make the upholstery softer and more voluminous.

The last stage of manufacturing is the upholstery of the sofa with fabric. It can be bought at a specialized store, having made a preliminary calculation of the area of \u200b\u200bsheathing and not forgetting a margin of 5-10%, necessary for cutting and turning on the frame.

To do this, all the front parts of the body and back must be measured and cut out pieces of material according to the obtained dimensions. They are fastened with a stapler on the invisible ends of the panels. To prevent the fabric from wrinkling at the corners, make cuts on it and pull it tight before shooting the staples.

Cushions for the back and seat of a corner sofa are best made of foam rubber with a thickness of at least 10 cm. Optimal Design covers for them - removable with a zipper. When soiled, the covers can be easily removed and sent to the wash. If you have no experience in sewing, then draw a simple pillow sketch and order the tailoring of covers in the atelier.

The sofa is the most important part of the interior. It is he who is the hallmark of every home, so he needs to be beautiful, reliable, practical. But the models presented by stores are often unusually expensive. The best solution is to create this piece of furniture yourself, which will save a huge share of the family budget.

In addition, for the sake of repairing a sofa made by yourself, it makes no sense to call the master. Knowing his device, it is easier to fix the breakdown yourself.

Comparing a photo of a do-it-yourself sofa and a purchased one, it is sometimes difficult to find significant differences in quality. By strictly adhering to the instructions, anyone can make a first-class product with their own hands.

This will require the following tools:

jigsaw;
special stapler for furniture;
screwdriver or drill;
grinder (a simple planer will do);
sewing machine;
sharp knife and scissors;
roulette.

Types and drawings of sofas are varied, but the main components of the product always remain:

frame;
mattress frame;
back;
side parts;
stuffing;
fabric upholstery.

To make them you will need:

wooden bars 40-50 mm in cross section;
plywood with a thickness of 5 mm;
stuffing (foam rubber, holofiber, batting);
furniture belts (optional);
textile material (batting, synthetic winterizer);
furniture fabric;
strong thread for stitching upholstery;
screws, corners, self-tapping screws.

The instructions for assembling the sofa are simple. The main thing here is the sequence of actions.

frame

Made from long bars. To give additional rigidity, plywood, chipboard, OSB and other sheet materials are used.

All this is fastened with self-tapping screws, screws and corners. They can be lubricated with glue before being screwed in, having previously drilled holes. For convenience, you can first connect the parts with glue.

Mattress frame

It is made from a solid sheet of chipboard or from fastened boards with a binding of furniture belts. It is not difficult to make it: first they are fastened with a stapler vertically, then the belts are intertwined with them and the belts are fixed horizontally (perpendicularly). Thanks to the binding, this piece of furniture will be perfectly springy.

Back and sides

Usually hollow inside. At the back, the frame is sheathed with a sheet of plywood and covered with a cloth, fixing it with a stapler. Ends are connected to front side. With the help of metal corners, you need to fix the back on the base.

You can give it a sloping shape, adjust the slope as you wish. The sides are made in the same way. Then, all the sharp ends of the resulting base are sanded with a grinder or planer to avoid rapid wear of the upholstery.

pasting

It is most convenient to use high quality foam mats, in order to avoid the appearance of holes on the surface, with a density of 35 kg/m3. Having measured the pieces of the required size, you need to paste over the back from above and in front, the side parts from the inside, the plane over the binding.

The ends of the foam rubber can be fixed with a stapler. After the glue dries, these elements are wrapped in batting or synthetic winterizer in order to achieve volume and smooth out irregularities.

Upholstery

It is better to sew covers according to patterns already prepared in advance. When this is not possible, you can, instead, apply the fabric to different elements and immediately stitch or make it easier and tighten it by turning it at the corners, but this method is not reliable. It is better to entrust the matter to professionals and contact the studio, where they will do all the work for you.

After all this, the easiest thing is to assemble. It will take only 2-3 days of diligent work.

When assembling a sofa with their own hands for a summer residence, people want without special costs use any materials at hand. Then, cheap or unnecessary parts can serve as a replacement for expensive ones. As a result, it turns out combining original design, style and functionality result.

For example, you can take wooden pallets. They are sold for pennies in the construction markets, for example. Used pallets should be thoroughly cleaned and washed. Then, even new panels should be sanded, if necessary treated with a water-repellent primer or painted.

It is not at all difficult to assemble a sofa from furniture panels. You just need to cut them with a jigsaw, measuring suitable sizes and fasten with screws. After, cover with paint and varnish and allow to dry. As a result, it remains only to make soft seats.

An unusual design move will be its manufacture from an old, outdated bath. To do this, remove the legs from it, clean the surface of the paint, cut off one wall with a grinder and grind the bumps.

The whole product is painted, the legs, processed separately, are returned to their place. It remains only to attach the seat and, if you want, trim the walls with soft components.

DIY sofa photo

Nowadays, furniture stores are literally crowded. various options upholstered furniture of domestic and foreign production, but the prices for it do not always please buyers. In addition, the cost of products sometimes clearly does not correspond to the quality of their manufacture. Therefore, in order to purchase a set of furniture, or at least one piece of it, you have to save up the required amount for several months or get into debt by taking out a loan.

However, there is another option to acquire the necessary interior accessory - this is to make, for example, a sofa with your own hands. For those who know at least a little how to work with carpentry tools, it will not be difficult to do this, albeit difficult, but very entertaining work. This publication will present several options for making sofas that can be used in residential areas or in a summer cottage. Of these, it is quite possible to choose the one suitable for a particular case, both in design and in the degree of its complexity. Practice shows that it will take three to four times less money than when purchasing a finished piece of furniture - so why not try to make it yourself.

Unscrupulous manufacturers often make the frame of upholstered furniture from which they have to, since the buyer does not have the opportunity to control the quality of the material. So, for the main frame, unedged bars eaten by a bark beetle are used, and ordinary cardboard is used to shape the backs. Well, the consumer for this literally penny material, lined with more or less decent trim, gives the amount for which you can buy a used car or live comfortably for the whole family for a month. Therefore, after making the calculations and making sure that you can save a very decent amount of money, you can get down to business on your own. In essence, the money that will be saved will become the salary of the home craftsman for making the furniture. In addition, there will be a reason to be proud of your talents in front of relatives and friends.

Tools for the job

Of course, certain tools will be required for the job, which will be useful in household not only for the manufacture of furniture, but also for repairs. They will not take up much space in a closet on a balcony, garage or in one of the outbuildings of a private house.

The list of necessary tools for work includes:

Hand circular saw, electric jigsaw and (or) hacksaw for wood and metal.
Roulette, folding rule, building level, square.
or a screwdriver with a set of nozzles.
Electric drill with a set of drills.
It's great if you have a manual router at your disposal.
File with a large notch.
Clamps for temporary fixation of structural elements before their permanent fastening.
Chisels
A hammer.
Pliers
Stapler and staples.
Sewing machine for making sofa covers.

It should be noted here that if you use hand tools, the work will take much longer, and the accuracy of the edges of the manufactured parts will not be guaranteed.

Instructions for making several models of sofas

First option: making a corner sofa

This sofa model may have different variants according to their size and design features:

For example, the side protruding part of the sofa can be installed both on the left and on the right side;

Various mechanisms are used for mounting the lower, retractable part;
Plywood or board can be used to make a sofa;
The soft parts of the structure can be made of foam rubber and synthetic winterizer, or only of synthetic winterizer.
For decorative sheathing, fabric or leatherette is selected.

Sofa prices

The dimensions of the sofa depend on the size of the room, the height parameters of its owners, and, of course, their preferences. Taking the dimensions proposed in the drawings, they can be “tried on” to the room where the sofa is planned to be installed, and if necessary, corrected in one direction or another, within reason.

This drawing will help to become a starting point in choosing the dimensions of this piece of furniture. However, you should pay attention to the fact that this model is somewhat different in its design from the version, the manufacture of which will be described in the table. However, the difference lies only in fixing the side back, which is built into the narrow section of the sofa.

This model is not as easy to manufacture as it might seem at first glance, as the master used special mechanisms for unfolding the sofa. But, having carefully studied the instructions for assembling it, it is quite possible to figure it out and come to the conclusion that making such a sofa in a standard apartment, and without leaving one room, is a completely achievable goal.

Manufacturing process - step by step

Illustration
	So, the first step is to make calculations and determine the size. Not only the convenience of the sofa and its optimal placement in the room will depend on this stage, but also the amount necessary materials and additional elements designs. To begin with, it is worth drawing a sketch of a sofa on a piece of paper and writing out all the necessary details of the design, indicating their quantity. Based on the compiled list, the final amount of materials that will need to be purchased is calculated.
	In this case, for the manufacture of the sofa, the craftsman chose plywood 20 mm thick. However, it can be used in combination with a board with a thickness of 20 ÷ 25 mm. The board is usually used to assemble the frame of the sofa, which is then sheathed with plywood. If a complex design option is chosen, then the thickness of the plywood for sheathing can be smaller and be 15 mm.
	As you can see in the illustrations presented, the work can be carried out in the same room where the sofa is planned to be installed. The only thing that needs to be provided is a solid base on which it will be possible to lay plywood and a board for marking and sawing. It is best to mark and make all the details of the structure at once, since when sawing wood, it naturally forms a large number of sawdust, which can be simultaneously removed from the room without spreading throughout the apartment. It is even better to stretch a plastic film on the floors of the room for the duration of these works, which, after they are completed, can be rolled up together with the resulting garbage and taken out of the house. With such a simple approach, you can save yourself from small debris, which tends to clog under baseboards and fly under other furniture.
	The sawing of plywood is carried out according to the marking using a manual circular saw, which guarantees a perfectly even cut edge. In the absence of a saw, you can also use an electric jigsaw, but it is more difficult to handle it, since its cutting part can go to the side. It is recommended to number and sign the finished parts of the structure - such foresight will significantly speed up the assembly of the sofa, since the components do not have to be searched for and selected for a long time.
	To fasten the details of the sofa into one structure, it is necessary to prepare wood screws with fine threads, 50 ÷ 60, 30, 25 and 20 mm long. Here you need to take into account that they will be screwed into the end side of plywood 25 mm thick, so their diameter should not exceed 5 mm. Self-tapping screws should have a regular head, as they will need to be sunk flush into the wood. To avoid splitting the plywood, it is recommended to drill a hole with a diameter of 3 mm before screwing the screws into it. Then the fasteners will be screwed in easier, and the base will remain intact.
	Now that the sofa parts and fasteners are ready, you can proceed to the assembly of the structure. Since it consists of two sections, the larger one is assembled first.
	The back is taken, and the side parts of the lower box are attached to it. They are screwed through the rear wall panel to the end side of the side element with two or three self-tapping screws.
	Now the resulting structure is covered with a sheet of plywood prepared in size. When the sheet is screwed on, this section of the sofa will gain rigidity and strength.
	The sheet is laid evenly, close to the back wall and screwed with screws. First, it is attached to the horizontal end surfaces of the side walls of the box, and then, through the back wall, the screws are screwed into the thickness of the laid sheet. The pitch of fasteners should be 150÷180 mm.
	The assembled section is installed in the place where the sofa will be permanently located, and they begin to assemble the second, narrow part of the sofa. First, the side walls and the back of the box are assembled together. Self-tapping screws are screwed through a smaller wall and back, forming the width of the section, into the ends of the long sides, with the same step of 150 ÷ 180 mm.
	Now you need to screw its bottom to the assembled box. The box is covered with a sheet, leveled and screwed with self-tapping screws with a step of their installation of 200 mm. To fix the bottom, you can use self-tapping screws of a shorter length - 20 ÷ 25 mm, and their hats must be sunk into the plywood surface, otherwise there is a risk of spoiling the floor covering with them.
	When assembled, the design of the narrow section of the sofa looks like it is shown in the photo. When the sofa is ready, the inside of the box can be used for storage. bedding or other things. However, so that less dust from the floors gets into the box, it is recommended to subsequently sheathe it with a cloth. For this, a thin lining material is well suited.
	Now that the frames of both sections are ready, they need to be tried on each other. They are installed against the wall and move among themselves. Next, you need to return to work on the first wide section.
	Since it is planned to make the sofa sliding, for the part that will slide in and fold under the horizontal surface, three plywood parts will be needed - this is a horizontal surface (sunbed), a front wall and a plank 30 mm wide. In addition to wooden parts, you will need a special metal folding structure, which can be purchased at a furniture fittings store. Its width is selected depending on the linear dimensions of the wide section of the sofa. This metal mechanism is fixed on all three wooden details that are not attached to each other.
	First, the metal structure is screwed to the inside of the front part, and its back side, equipped with wheels, is fixed to the plywood plank. After that, the addition test can be performed. Any bar is applied to the upper structural element, which is pressed. In this case, the upper metal shelf of the mechanism should fall to the bottom.
	If the system works well, then you can move on to temporarily fixing the resulting folding structure on top of the plywood sheet that forms the lounger.
	It is temporarily fixed because it is necessary to determine the location of the metal parts of the mechanism on it, as well as to try it on. general design sofa. You will have to remove the sunbed for laying foam rubber on it and covering it with fabric.
	So, the retractable part is fitted to the box of the wide section. On the this stage it is important to make sure how well the parts fit together, and whether they freely enter the space under the bed of the main section.
	The front side of the pull-out part of the sofa should have the same height as the surface of the lounger of the main section.
	Now it is necessary to verify the rise of that part of the lounger, which is fixed on the retractable structure, to determine the height of the corners along which it will walk, as well as the location of the stopper.
	In order for the mobile part not to extend completely, but, reaching the edge of the lower part of the lounger, to stop, a rectangular profile pipe is fixed to the edge of the inner side of the wide section. For the convenience of marking its location, and then fixing it, the wide section is turned over and laid on the back wall.
	While the section is in an inverted position, a line is also marked on its side walls, on their inner side, along which the guide metal corners are then placed and fixed. Thanks to these elements, the mobile part of the sofa will slide in and out freely. The corners are screwed through holes pre-drilled in the corners with self-tapping screws 20 mm long. Fastening is carried out with a step of 180÷200 mm.
	When the retractable lounger is fitted to the surface of the main surface of the sofa, the plywood can be removed. So it will be convenient to make another fitting, and then lay the foam on the retractable surface.
	The retractable part is installed with wheels screwed to the plywood plank on the corners fixed on the sides of the wide section, and slides into the space under its lounger.
	Before making the soft part of the lounger, it is recommended to round the corners of the plywood a little with a jigsaw, or process it with a file with a large notch - this will help keep the sheathing material from damage. Now you can proceed to the sheathing of the retractable surface of the lounger. To do this, foam rubber with a thickness of 100 mm of the desired size must be prepared. It is recommended to glue it to the plywood surface. For this purpose, polyurethane glue or “Moment”, which is pointwise applied to plywood, is suitable. A synthetic winterizer is laid on top of the foam rubber.
	The next step is to put on a sheathing cover on top of the synthetic winterizer, wrap it on the reverse side and fasten it with staples driven in with a stapler.
	When the mobile part of the lounger is sheathed with material, a folding metal structure is screwed back to it. This finished part of the sofa needs to be set aside for the time being.
	Next, you can move on to sheathing the plywood base of the lounger for the narrow section of the sofa. A foam rubber sheet is also glued onto it, covered with a padding polyester, which is well leveled. After that, the lounger is sheathed with leatherette - it is also fixed to the plywood with brackets. The upholstered lounger is also set aside for the time being.
	The next step is to cover the backs of both sections of the structure with fabric. The corners of the plywood backs also need to be treated with sandpaper, then pieces of synthetic winterizer are fixed along their edges, after which they are covered with fabric, which is fixed with staples on the back of the walls.
	Further, the front part of the box and half of the side walls of the narrow section of the sofa are upholstered with leatherette. It is recommended to lay a synthetic winterizer under the sheathing material. Sheathing of only these parts of the structure is carried out because on the sides, closer to the back wall, the side back of the sofa will be fixed on one side, and a wide section will adjoin the other side.
	Since the lounger of the narrow part of the sofa must rise and fall. special lifting mechanisms are marked and fixed in the box of this section.
	To check the operation of these structural elements, after fixing them to the sides of a narrow box, a plywood strip is alternately laid and fixed on top of them and pressed down, and then rises. The bar should be springy - this will subsequently ensure easy raising and lowering of the narrow section lounger.
	If the mechanism works satisfactorily, then in place of the fixed bar, it is installed and screwed to the sheathed soft part of the narrow section lounger structure. Here you will need an assistant, since at this stage the sunbed must be held at the right angle.
	Now the pillow covers sewn from leatherette are filled with synthetic winterizer and sewn up. It should be noted here that instead of padding polyester, pillows can also be formed from foam rubber.
	Further, from plywood and wooden slats lateral backs are formed. They can have a rectangular top or rounded on one or two sides - this design is made according to one's own desire. Some craftsmen, instead of wooden planks, use thick thick cardboard 2 ÷ 2.5 mm thick, which is sprayed with water from a spray bottle before fixing. Wet material is more plastic and takes the desired shape more easily. After its installation, before sheathing these structural elements, the cardboard must be dried well.
	At the next stage of work, the wooden or plywood-cardboard construction of the side backs is completely upholstered with padding polyester, except for the lower part. The material is secured with staples.
	The next step is to put leatherette covers on the backs and fasten them with staples to their lower part.
	Ready-made backs are installed and fixed on both sides of the overall structure - one on the outside of the narrow one, the other on the wide section.
	The backrests are fixed through the walls from the inside of the box with four to five self-tapping screws. In order for the fasteners to fit snugly into the material, the backs must be pressed against the wall, or they must be held securely by an assistant.
	As a result, the design of the sofa without removable pillows will look like this illustration.
	To expand the sofa, it is necessary to push forward the lower part with the sunbed recessed into it.
	Then, raise the sunbed to the same level with the rest of the pillows using the installed retractable lifting mechanism. It should be noted here that the author of the project went the hard way, choosing a mechanism of a rather complex design for unfolding, requiring precise installation. If such a system is not found or seems too complicated, then you can do it a little differently by making a retractable box with a plywood lid. However, in this case, instead of separate pillows, a double folding mattress is fixed to the wide section of the sofa. For the narrow section, two parts of the mattress are provided - the lower one is fixed to the plywood part of the lounger, while the upper one is made removable. The latter is simply removed and removed into the interior of the section when the sofa is unfolded. Thus, all pillows of the structure will be on the same level. In this case, four wheels will need to be fixed on the retractable part of the sofa, and a stopper should be installed under the plywood lounger of the wide section.
	Another nuance that I would like to clarify. In some models of this type of sofas, the side back, installed on a narrow section, seems to crash into it, that is, it does not go beyond the overall design. This option is convenient if the sofa should be pressed against the wall with this side, so there will be no space between it and the sofa, in which dust will inevitably accumulate.
	If you choose a model with a built-in side back, as well as with mattresses instead of individual pillows on the lounger, the corner sofa will look like this illustration. Moreover, in this case, all the pillows are made of foam rubber, which must be covered with padding polyester, and then filled into fabric or leatherette covers.

Second option: sofa book

Design features and required materials

This version of the sofa can be called traditional for many Russian apartments and, despite the fact that the model was developed several decades ago, it still remains in demand by buyers. This fact can be explained by the fact that it is simple and reliable in operation, and the mechanism designed for its unfolding is easy to mount, as it has a clear, simple design.

Today, the task of manufacturing such a sofa is also simplified by the fact that a large selection of fittings is presented in modern furniture stores.

For example, fiberboard, which was previously used for sheathing a structure, can be replaced with lamellas designed specifically for installation on beds and sofas. They not only perfectly replace sheet material, but also compensate for the softness of the structure, as they tend to spring. Thanks to this quality of details, the thickness of the mattresses can be made smaller.

The design that will be presented below must be manufactured and assembled in accordance with these recommendations, but design decoration, as well as the shape of the side backs, can be made according to your own sketches, but in compliance with the basic dimensions.

So, the sofa book consists of the following elements - this is a backrest, a lounger seat, side backrests and a box for storing bedding or other things.

To make a sofa of this design you will need:

Board with a thickness of 20 ÷ 25 and a width of 200 mm for the sofa frame.
A beam with a section size of 50 × 50, 60 × 40 and 50 × 30 mm.
Fiberboard 4 ÷ 5 mm thick.
32 furniture slats 65 mm wide, 500 mm long.
Foam rubber and synthetic winterizer.
Upholstery fabric.
Sofa unfolding mechanism (paired).
Legs.

Illustrated step by step instructions for making

The first step is to draw up a sketch drawing of the sofa and put down the dimensions of all the details on it. Having such a graphic document in front of your eyes, it will be much easier to make all the necessary structural elements.

Illustration	Brief description of the operation to be performed
	The assembly of the sofa box is carried out first. Its size should be 1900 × 800 mm. Moreover, first, bars are fixed to the long details of the box, along their edges - they are screwed using self-tapping screws 60 mm long. The next step, to the inner sides of the bars fixed on the long walls of the box, the side parts are screwed. Before the final tightening of the fixing screws, it is recommended to measure the diagonals of the box - they must have the same size.
	The next step, in order to give rigidity to the structure, in the middle part of the bottom area of the box, two transverse bars with a section of 50 × 30 mm and a length of 800 mm are screwed from the outside. They are installed at a distance of 650 mm from the edge and 600 mm between them. In order for the bars to be fixed flush with the underside of the box, grooves 55 mm wide and 30 mm deep are cut in the boards at a specified distance from each other. In these grooves and fit, and then the transverse bars are fixed. After the box is assembled, its bottom is sheathed with a fiberboard sheet, the size of which is 1800 × 800 mm. Fixing the sheet on the frame can be done with staples, nails or self-tapping screws 20 mm long.
	The next step is the back and seat frames - their design has the same linear parameters. For their manufacture, a beam with a section of 50 × 40 mm is prepared. Seven parts of the following sizes are cut out of it: 3 pcs. - 650 mm; 2 pcs. – 400 mm, 1 pc. - 1890 mm and 1 pc. - 1880 mm. The frames are assembled in the following sequence: first, on a beam 1890 mm long, 50 mm are deposited from its edges. Bars 650 mm long will be fixed in these places. Their other side is fixed along the edges of the beam, which has a length of 1880 mm. Then, on long bars, their middle is determined and the middle crossbar is installed. Further, elements 400 mm long are attached to the free edges of the longest beam. In addition, they are screwed with self-tapping screws 70 ÷ 80 mm long to the extreme short transverse bars. These elements, before fixing, are cut in the upper part at an angle of 30 degrees. They will be in the front of the lounger and in the upper back. When unfolding the sofa, the side back should be between these protrusions of the structure.
	The simplest connection of a beam is in half a tree, that is, in each beam, at the place of its connection with a perpendicular one, half of its thickness is cut out at the corners. In our case, this is 20 mm, that is, the groove should have a size of 50 × 50 × 20 mm. To install the middle beam, from each of its edges, as well as in the place marked on the long beam, a place is also cut out 20 mm thick, and the groove must also have the size indicated above. Then the transverse beam is first glued into the groove, and then screwed with two self-tapping screws 30 mm long, with their diagonal arrangement. It must be said that it is possible to fasten structural elements with other connections, but this is one of the simplest.
	Further, the long sides of the frame are marked for the installation of lamellas, the distance between which should be 60 mm. According to the marking, metal or plastic brackets with grooves are fixed, which come with the lamellas. After fixing them on the frame of the backrest and lounger, the edges of the lamellas are inserted into them.
	The next step is to make the side backrests-armrests. First, according to the dimensions shown in the illustration, four identical parts are marked out, drawn and cut out.
	Then the two cut parts are stacked in a mirror image to each other and marked. According to this marking, bars having a thickness of 50 mm are fixed. To begin with, they can be glued with wood glue. Their width can be the same or different, the main thing is that in the places where they will be attached to the sofa box, the beam should have a width of at least 80 ÷ 100 mm, since holes for fixing bolts 120 × 8 mm in size will be drilled in them. Bolt holes are drilled immediately after the glue on which the frame beam is fixed has dried, at a height of 150 mm from the bottom of the side back. Further, the frame is covered with a second similar part, cut out of fiberboard, which is nailed to it with nails 30 mm long. After that, the sides are turned over, and the other side of the fiberboard is also nailed and holes are also drilled in it.
	Further, in the side walls of the box, at a height of 150 mm, with an indent from the edge of 100 mm, holes with a diameter of 10 mm are drilled to fix the side walls. In addition, at this stage it is most convenient to screw the legs of the sofa to the box, since after fixing the remaining elements, it will be more difficult to turn the box over.
	The next step is to attach folding mechanisms to the back, sunbed and box. The scheme of their installation is presented in this illustration. Fixation of metal elements is carried out with the help of bolts, for which holes are drilled in the side walls of the structures. In addition to bolts, self-tapping screws are used to fix the mechanism - for example, they are additionally attached to the corner plates on the back and seat frames.
	To begin with, on the side wall of the box, you need to find the middle, 5 mm is deposited on each side of it, at this distance from the middle the back and sunbed are laid. A mechanism is attached to them and marks are made on all the details of the sofa, along which holes will be drilled. Further, the mechanism is fixed on all the details of the sofa.
	After the folding system is fixed, you need to try on the side backs to the sofa. But so far they are not screwed, since before that they will need to be sheathed.
	Sheathing is done starting from the back and sunbed. To do this, the sofa is laid out and first interlining is laid on the lamellas, then a thin synthetic winterizer, and on top of it - foam rubber 50 mm thick. So that the foam rubber does not interfere with the folding and unfolding of the sofa, its corners adjacent to the mechanism are cut out, as shown in this illustration.
	To make the back and lounger more comfortable for sitting, additional foam rubber strips are glued to their edges on top of the foam rubber, 200 wide and 20 ÷ 25 mm thick. Then, the entire flooring is covered with another sheet of foam rubber, 20 mm thick, but having a large width, such that it can be bent under the thickness of the sunbed structure and behind the back. There, the foam rubber is fixed with staples using a stapler.
	The foam rubber fixed on the frame is covered with a thin layer of synthetic winterizer - these materials are well fastened together without the use of glue. After that, sewn-to-size covers are put on top of the back and sunbed, which are nailed to the wooden structural elements with staples. If desired, in several places of the sofa, buttons sheathed with the same material are installed with strong cords inserted through them, which are threaded through the sheathing and tied to the lamellas, and their ends are shot to the wooden structural elements with brackets. After sheathing the lounger and the back of the structure, the upholstery is also fixed on the front side of the base-box.
	Next, move on to work on the side backs. The first step is to glue the foam on the top side. On the rise and in the upper part, the thickness of the foam rubber should be 50 mm, and in the lower area where the hand will lie - 80 mm. It should turn out approximately as shown in the photo.
	In the next step, the armrest of the side backrest is covered with foam rubber 20 mm thick, which is nailed to the fiberboard with staples.
	On top of the foam rubber fixed on the armrest, another foam rubber sheet 20 mm thick is fixed. It should protrude from the front of the armrest by about 100 mm.
	The front protruding part of the foam rubber is bent and adjusted with staples to the front of the side back frame. Further, it is recommended to cover the foam rubber on the armrest, as well as the entire area of the walls below with a padding polyester, which is also nailed with staples.
	Before performing the next operation, bolts are inserted into the holes drilled in the side backrests, onto which washers are put on. The next step is to cut out pieces of fabric of the desired size and shape, and then they sheathe the walls of the sides. First, the fabric is nailed with staples in the upper part, and then tucked under the bottom of the back and fixed there.
	Further, the armrests are covered with separate pieces of fabric. These segments are fixed under the armrests, on top of the already fixed fabric, first from the outside, and then from the inside of the armrest. After that, the fabric is neatly folded and fixed with a stapler from the front of the side backs, and is closed on top with a wooden decorative overlay, which, like all accessories, can be purchased at a specialized store. It remains only to screw the side backs to the lower box through the previously drilled holes. This process is carried out from the inside of the frame structure.
	When unfolded, the finished sofa-book looks as shown in this illustration.

Prices for corner sofas

corner sofas

Find out some of the available options from our new article on our portal.

The third option is a sofa for giving from an old bath

Design features and required materials

Old bath after holding overhaul often becomes an unnecessary burden. Usually it is taken to a landfill or to a summer cottage and left to rot in the far corner of the site. At best, it heats water for watering especially whimsical plants. At the same time, a lot of money is spent on acquiring garden furniture. At the same time, not many people know that from a bath that has served its main role for the allotted time, it may well turn out to be a comfortable and original sofa that fits perfectly into landscape design area and will last for many years.

Such an unusual piece of furniture can be installed outdoors, on the terrace, in the gazebo or. With proper design, such a sofa and the interior of a country house will not spoil.

In order to make such a sofa, both a cast-iron and a steel bath are suitable. Of course, it is more difficult to work with cast iron, and it is also not easy to move such a piece of furniture from place to place. But with a steel bath, no special problems are foreseen. Sofas made from old bathtubs will last for many years if you work on them well. Moreover, what design and color to choose for the sofa - the master is determined by himself. The most important thing in the manufacturing process is preparing the base for applying paint, cutting out the excess part and processing the edges after trimming them.

Check out unusual, inexpensive and very practical do-it-yourself production, in new article on our portal.

Step-by-step instructions for making a sofa from a cast-iron bath

Illustration	Brief description of the operations performed
	In this version, for the manufacture of the sofa, an old cast-iron bathtub with legs-paws is used, which are always the decoration of this accessory, and we will not throw them away. The illustration shows that the enamel coating of the container is in a very unenviable condition. In all likelihood, she had lain in an unheated shed for more than one year, or even lay near the fence in the open.
	Cracked enamel and the resulting corrosion stains will definitely have to be removed from the surface of the bath. Since the cast-iron surface is not perfectly smooth, unlike a steel bathtub, you will have to work hard on it to remove all old dirt, cracked enamel residues, scale pieces from it and give it an aesthetic appearance.
	The legs were fastened to this model with the help of bolts, which, during the operation of the bath and waiting for its “renaissance” in the form of the original sofa, have become very rusty, and one can hardly hope that they will unscrew without using special means. Therefore, in order not to complicate the process and not to spoil the thread, a composition (for example, WD-40) is sprayed onto the mount, which helps soften the rust. Then this area is left for some time, indicated on the cylinder by the manufacturer. After this time, the nuts from the bolts should be twisted without difficulty. Other threaded parts should be treated with the same tool, which must be removed before cleaning and painting the container.
	Before moving on to cleaning the surface, markings are made along which the front of the bath will be cut out. In this case, a cutout had already been made in one of the edges of the bathtub, apparently, this had to be resorted to in order to carry out water pipes when installing the mixer. So that this man-made flaw does not spoil the entire appearance of the structure being created, the cutout is marked from this side.
	To mark the bath, a square and a dark marker are used, which will be clearly visible on a light surface. To begin with, the lower part of the cut is determined - for this, a square is attached to the bath, and a perpendicular line is drawn, along which it will be easier to navigate, making the slope at a greater or lesser angle.
	Further, the exact lines are outlined along which the cutout will be made on one and the other side of the container. Since the bathtub has a curved surface, and the cutouts must be in harmony with each other, repeating the shape of the container, it is possible to measure the required distance from the vertical line of a right angle using a tape measure or square, first in height and then to the side. One way or another, the lines on both sides will be located at different angles.
	Having determined the exact outer line, it must be repeated on the inner surface of the container, since when cutting, work will be done both from the outside and from the inside of the bath. From the inside of a curved surface, it is quite difficult to determine a right angle, so the transfer of the line will have to be done, so to speak, by eye. However, special accuracy is not required from the master here - the curvature of the lines is still necessary, and everything depends to a greater extent on the subsequent processing of the cut edge.
	The second side of the container, where the drain holes are located, is not so curved - more close to right angle. But it is impossible to make a cutout exactly rectangular, otherwise the visual balance of the structure will be lost. Therefore, based on a vertical straight line, and taking into account the cutout angle that was found for the other side, the slope for the second side of the container is also determined. When the optimal slope option is found, the lower points of the lines of the two sides are connected by a horizontal line.
	Now the grinder comes into operation with a metal disc installed on it. There are no problems with steel, but the task of cutting cast iron is a very difficult task, one might say - delicate. It is impossible to praise the master who demonstrates cutting in these illustrations - it is imperative to fix a protective casing on the tool, since it is not known how such a heavy and fragile metal as cast iron will behave. It happens that when cutting it, the circle begins to tear, and this is very dangerous. The casing, of course, somewhat closes the view, so the cut must be done very carefully. Cast iron is cut very carefully, while it is necessary to protect the face by wearing a special mask, as the disk may be damaged or part of the metal being cut may fly off. There is no need to hurry, since it is easy during this process to overheat the grinder and completely render it unusable. So it is better to cut in small sections, 100 - 150 mm each, allowing the tool to rest and cool. First, a cut line is drawn from the inside, on the curved sides of the bath. Further, the cut is made from the outside of the container along the line drawn earlier.
	It is very difficult to cut high-quality bath enamel if the cut is made from the inside. So the work is best done for the most part from the outer surface of the bath. If you have to cut some area exactly along the enamel, then it is better to first install a diamond wheel and carefully clean the enamel along the cut line with it. And then proceed to work with a cutting wheel for metal. Having cut out one side of the bathtub, starting from the upper side, go to its second side, to the drawn lower horizontal line.
	Now it remains to make a horizontal cut, and the first, perhaps the most difficult and dangerous stage of work, will be completed. For convenience, the bath is laid on its side, and then, if necessary, props are installed under it, since when cut, it must stand very stable on the surface. Basically, this applies to steel baths, since they have less weight, while the cast-iron version usually fits snugly to the surface under its own weight.
	This is how the bathtub will look like, from which the fragment, which is unnecessary in this case, is cut out. Now, you can move on to a less complicated, but very dirty operation.
	Next, there is a mandatory process of leveling and grinding the cut, since the edge must be even and smooth, otherwise you can seriously injure yourself about its notches. The work is carried out with the same grinder. First, a cutting disc for metal is installed on it, with which the remaining metal burrs are cut off.
	Then, the edge is processed with a grinding disc. The cut end and its side parts are polished. If the sofa is made from a steel bath, its cut edge can be beaded down a little, since the metal is thin, and its cut will remain sharp even after grinding.
	Next, the outer surface of the bath is cleaned with a metal brush mounted on a grinder, and then with an emery disc. The dust formed on its surface is collected by a vacuum cleaner. After that, the outer side of the container is covered with a primer composition intended for processing metal products. The primer layer is applied carefully with a soft brush, as the substance must get into all the pores of the cast iron surface. The soil should dry well, after which the surface is again cleaned with an emery disc with a medium grain. Dust after cleaning is also collected by a vacuum cleaner. You can immediately thoroughly clean and prime the previously removed bath legs, as shown in the illustration.
	They proceed to the next operation - the first layer of paint of the selected color is applied to the outer surface of the bath. Paint must be chosen for external work, intended for metal. It will prevent the appearance and spread of foci of corrosion under the influence of the external environment.
	After applying the paint, the smudges formed on the surface of the bath must be collected with a soft cloth, leveling the paint layer with it. The napkin is applied to the desired areas of the surface and pressed against the metal, collecting excess paint.
	When the paint dries, another layer is applied on top of it, which will make the outer surface of the bath (that is, sorry, the sofa) smoother, which will reduce the risk of dust and dirt particles being trapped on it. This is especially important if the sofa is planned to be installed outdoors.
	The legs of the bathtub and their fastenings must also be well cleaned of rust - their processing, as we have already seen, is usually carried out at the stage of priming the bathtub. Cleaning, however, will have to be done manually. Then all parts are treated with a primer, dried, cleaned and painted, it is possible in a color that contrasts with the rest of the surface of the bath. After that, the legs are fixed on the bath using a threaded connection. If possible or necessary, fasteners are replaced with new ones.
	Now they move on to work on the inner surface of the trimmed bath. The first step is to repair the chips that formed along the edge when cutting the metal. For this purpose, an epoxy or polyurethane two-component putty is well suited, which is applied along the inner edge of the bath with a spatula. The putty is leveled and left to dry completely.
	When the putty dries, the area where it was applied must be well cleaned and then sanded using, for example, an eccentric sander with emery nozzles of various grits. If there is no such tool, then you will have to work manually - with sandpaper.
	Further, the entire inner surface after cleaning is covered with a primer and left to dry. It is very important to treat the holes that are in any bath well, as corrosive processes can begin to spread from them. In order to prevent the primer, and then the paint, from getting on the outside of the container, paper is fixed on all edges of the masking tape, which is removed only after all work is completed.
	When the primer is completely dry, all surfaces are cleaned with an eccentric sander with an emery nozzle. The primer should be as if rubbed into the cast iron surface.
	Further, the inner surface is covered with enamel on metal. It is best sprayed with a spray gun, but can also be applied with a brush. If the staining will be carried out manually, then the paint needs to be slightly diluted with a solvent and applied, picking up on a brush a small amount of coloring compound. Only in this case the paint layer will be even. Some craftsmen apply the paint with a sponge that is dipped in the paint and then pressed against the surface. This process is quite lengthy, but with the help of a similar technique, original stains with color transitions can be reproduced on the surface. In addition, the inside of the bathroom will acquire a pleasant roughness.
	Now it is worth considering the manufacture of a mattress that will be laid on the bottom of the sofa. All such soft parts can be made both before and after painting and drying the container. But in order for the mattress to fit perfectly on the bottom of the bath, you need to measure it on the spot, that is, lay a rectangular sheet of foam rubber cut to size, and then round its corners in accordance with the shape of the bottom of the sofa. For this work, you can use a sharp clerical knife and scissors.
	The cut foam rubber is laid on the fabric from which the cover will be made. On the fabric, the foam rubber is outlined with a marker, and when cutting the material, 10 mm per seam is taken into account, that is, 10 mm recede from the line left on the fabric by the marker. You will need two such parts, and in addition to them, you will need a strip of the same or another material equal to the thickness of the mattress plus 10 mm on each of its sides.
	You also need to cut two ribbons 30 mm wide and a length that is equal to the edge of the mattress, plus 20 mm for the seam. In addition, you will need to prepare a cord that will be sewn into the tape - it is necessary to maintain the shape of the mattress. The tape is bent in half, a cord is inserted into it and fixed with sewing pins, after which the tape is sewn along the fastening line on a typewriter.
	Further, the resulting edges are fixed on each main fabric part of the future cover, with the same pins and stitched to them on a typewriter, after which the pins are removed. After that, the parts are combined with the front side inward. Then, first, a side tape is pinned to one part from the wrong side so that the edge of the piping with a cord sewn into it is on the front side. Then, the combined parts are sewn on a typewriter. Further, the second side of the tape is pinned to the second part of the cover and also sewn, but only from three sides. The fourth side will be sewn by hand after the cover is put on the foam.
	The finished mattress should fit perfectly into the bottom of the sofa made from the bathtub.
	If desired, the back of the bathtub can also be equipped with a soft support cushion by gluing it with polyurethane or epoxy glue. If the goal is to get a sofa with a completely soft inner surface, then it is possible to sew a removable insert from foam rubber and fabric, which will completely cover the entire structure from the inside. Here already - the widest scope for creativity.

It remains only to note that if you turn on your imagination, then from the bath you can make not only a sofa, but also an armchair, table and other furniture accessories.

Prices for popular sofas

inexpensive sofa

Read interesting information about new life for old stuff in new article −

Now that the detailed instructions for making the three different types sofas, you can decide on the choice of the desired model in accordance with the planned place of its installation and the intended functionality of this piece of furniture.

And at the end of the publication - a demonstration of the manufacturing process of another original and relatively simple sofa model.

Video: Self-made original sofa

Sofas are one of the most necessary things in the interior of any apartment and indeed, they perform very well. useful features in any room: they rest and you can store things in them.

In this article we will try to tell you how to make a sofa with your own hands. After all, sometimes there are circumstances that do not allow you to make this rather expensive purchase, and then your skills and ingenuity should come to the rescue.

With the help of this article, you can make a simple pallet sofa that does not require even an average skill level from you, and a rather complex corner sofa, for the manufacture of which you need to have some skills in carpentry.

In contact with

Classmates

Advantages of making your own upholstered furniture

Let's see if we need to make a sofa with our own hands and what is the plus of this work.

Significant savings in money. Sofa own production will cost you several times cheaper than its store counterpart.
Quality. There is such a phrase "do as for yourself." The owner, who makes furniture for himself, approaches the quality of the material used as responsibly as possible. You choose the best and dried timber, upholstery without "chemistry" and foam rubber with a certificate.
Design choice. Who, if not you, knows best what is most suitable for your apartment. Moreover, it is not always possible to choose a sofa in the store that is ideally suited to the interior of your home, but you yourself can always make all your wishes come true and assemble a sofa that is most suitable for the decor of the apartment.
Dimensions. You can always make furniture that is the most suitable in size to your room. This is especially important for small apartments, where you want everything to fit perfectly and, at the same time, not take up much space.
Self stretching. If you have made sofas at least once with your own hands, then later, when you change the design of your apartment, you will be able to independently carry out the hauling with the most suitable fabric. The same can be said about replacing the old skin with a new one.
A self-assembled sofa will always be the subject of your pride in front of guests and members of your family.

How to make a sofa with your own hands video:

Pallet sofa

Of course, a pallet sofa is not a top. design art, but still you can give a bunch of examples of how it will be useful in a given situation.

Such a sofa can be very useful for temporary use. It is mounted very quickly and if, for example, old sofa broken, and you have not yet purchased a new one, or when moving to a new place of residence, when all the furniture is still in old apartment then this self assembled furniture would be the real way out.
This sofa will cost you almost nothing, so if you don't have the money for a new one yet, you can use this option.
Having built such a sofa in a country house or a country house, it will add originality to your home.
When assembling a sofa, you will gain invaluable experience that will be useful in the subsequent manufacture of similar structures. This will be your first step, not fraught with significant difficulties, because its assembly does not even involve using the drawings of the sofa.
Sometimes there is nowhere to throw extra pallets, so why not use them for such a practical benefit.

But when using pallets, you cannot use those on which oils, chemicals and other harmful substances were transported. Therefore, be sure to check this issue.

corner sofa

If you decide to update your kitchen and equip it with an additional design element, which will also perform several functions, then you need to assemble a sofa in the kitchen with your own hands, usually in the form corner design. After all, such a sofa can serve as a place for eating, for relaxing and, moreover, to be a repository for all kitchen utensils.

Note!

With minimal knowledge and skills in carpentry and assembly work, you can produce a comfortable and beautifully designed small kitchen sofa.

Another positive point is that tables of almost any geometric shape are suitable for such a sofa.

Initial stage of work

To begin with, we choose a place where this furniture will stand and, in accordance with this, we will make all the main measurements. We will need to find out the length of each part of the sofa, the width of the seat and its height. And after that, all measurements will need to be transferred to the drawing of the corner sofa. With the help of a properly drawn up drawing, it will be much easier for you to manufacture and assemble it.

When measuring, try to correctly calculate the dimensions of the chair, namely the depth and height of the seat. After measuring, having calculated the amount of material, go and buy it in the right amount, you can with a small margin, leaving a small percentage for damage.

Sofa assembly

Cut the details of the desired size and proceed to the assembly of the frame. When assembling the frame of the sofa, tightly join its lower part, which can first be glued and then put on the screws. After assembling the frame, prepare the panels. The panel material is usually chosen medium density. It is strong enough and also cuts well with a conventional circular saw.

Finish the assembly work by fastening the panel to the frame with long screws. Before final screwing, move all the parts to the kitchen and assemble the sofa, making sure it is assembled correctly. The last step there will be a fastening of the backs, which are also glued first, and then screwed.

Final work

To increase the functionality of the sofa, use hinges when assembling the seat. Then you can open them and use them as an additional container for items. Then we carry out the upholstery of the sofa with a cloth. It must meet two requirements: to be practical and beautiful. Fabrics on synthetic fibers are famous for their particular practicality, which are remarkably clean and also repel moisture and dirt. Also an excellent material is leather, which is practical and easy to care for.

Sheathing process

Sofa eurobook

Another piece of furniture in your apartment can be a Eurobook sofa. This is a very comfortable bed that easily transforms into a seating area. Inside them is a roomy niche for a bed or other items.

Note!

The main parts of such sofas are the back, seat, sides and base.

If you decide to assemble such a design yourself, then you need to understand that it is more complicated than the first two options considered, but this is not an impossible task.

Assembly method

In general, to create such sofas, two assembly methods are used from beams and wooden sashes. The first option is more complex and will require average mounting skills and a longer work process. But this option is also more durable, and this quality is quite useful in the manufacture of sofas.

See inaccuracies, incomplete or incorrect information? Do you know how to make an article better?

Would you like to suggest photos for publication on a topic?

Please help us make the site better! Leave a message and your contacts in the comments - we will contact you and together we will make the publication better!