coupe 

Installing a gas converter in a wooden house. Do-it-yourself installation of a gas convector: an algorithm of actions and advice from professionals. Gas convector installation, gas pipeline connection

Gas convector - a type of gas heating equipment. The device has general type designs and a wide range of thermal power (models). Its use is often due to the lack of a stable water supply, the cheapness of natural gas compared to electrical energy (electric heaters are also installed in the absence of water). Installing a gas convector is a simple process, but it has a number of features.

The principle of operation of the gas device is based on the combustion of natural gas and the heating of the air circulating through the design of the convector. The air flow moves in a closed cycle - room-convector-room.

The gas convector consists of the following main structural elements:

  • Metal housing equipped with grilles for air circulation;
  • Heat exchanger with combustion chamber;
  • Air supply fan (smoke exhaust);
  • Room air circulation fan;
  • Coaxial or separate chimney;
  • Gas burner built into the heat exchanger;
  • brackets for wall mounting(often purchased separately);
  • Control and management system.

The heat exchanger has high-quality fins made of metal plates to increase the heat exchange area. A gas burner is built into the heat exchanger - it burns gas and heats the heat exchanger. For combustion, outside air is supplied to the chamber with the help of a fan. The same fan serves as a blower to remove combustion products. Air and flue gases move through a coaxial chimney (pipe in a pipe) or separate pipes - air is supplied through one, smoke is removed through the other.

A fan is installed inside the casing, which circulates the internal volume of room air through the convector casing (along the surface of the heat exchanger). There are two types of installation of convectors - rigid (with a firm fixation of the device) and on a wall bracket with the possibility of changing the direction of air supply to the room. Mounting on a bracket is possible only with separate chimneys, which are connected to the device with flexible connectors - this allows a slight reorientation of the air flow direction.

Some manufacturers equip gas convectors with adjustable grilles (such as shutters) for manual or automatic change in the direction of heated air supply to the room.

Control gas appliances produced from a remote control. The system is equipped with the necessary safety sensors and blocking limit modes.

Gas convector installation, gas pipeline connection


Installation of a gas convector is strictly linked to the implementation of a gas project. Any equipment that uses natural gas in its operation requires a permit and the implementation of a gas project.

To obtain permission to install a gas convector, you must submit an application to the organization responsible for the operation of the gas pipeline to which the equipment is planned to be connected. Independent re-installation of gas pipelines is strictly prohibited.

The operating mode of this type of installation is characterized by a high heating rate and cyclicity, so installing a gas convector in an apartment or private house most likely will not create comfortable living conditions. Temperature fluctuations in the time interval will reach decent values.

It will also not be possible to install a gas convector with your own hands - you need to have a special license for this type of work. Installation of convectors in wooden houses requires compliance with safety measures building structures from wood from contact with elements of the device having high temperature. This interaction of wood and hot metal can lead to fire.

The most popular area of ​​application for gas convectors is the heating of large volumes of premises - production workshops, hangars, warehouses, and so on.

After receiving the application and processing it, technical conditions for connection to the gas pipeline are issued. They indicate the connection point, gas consumption and other indicators. Based on the technical specifications, a gas project must be executed.

The gas project indicates the installation locations of the devices, the methods of their connection (subject to the requirements for the installation of gas convectors), the configuration of the supply gas pipeline. The project is coordinated with the organization - the owner of the gas pipeline. Only after that proceed to the installation of equipment.

The installation process itself is quite simple. Holes for coaxial or separate chimneys are equipped in the wall; when supplied from an external gas pipeline, there is a hole for gas inlet. The convector body is mounted on the brackets. Smoke exhaust structures are connected to the body.

The holes through which the chimneys pass are sealed with non-combustible material. In the case of wall-mounted installation of the device (not on a remote bracket), the wall is also insulated from the convector with fireproof materials with low thermal conductivity (asbestos cloth, and so on). Electrical wiring (220 V) is supplied to the convector. Implemented electrical connection convector (built-in fans are powered by electric motors). A remote control panel for convector operation is installed in the accessibility zone.

For the installation of a gas pipeline, you need to attract an organization that has a license for the corresponding type of work. The installation of the gas pipeline is carried out by electric arc welding, the laying of the gas pipeline is carried out in compliance with the requirements of the project.

After the installation work for gas, pressure testing and delivery of the gas pipeline to the representative of the organization of the owner of the gas pipeline is carried out. Checking the joints of pipelines for tightness is carried out by washing. If leaks are detected, they are eliminated and a new tightness test is performed. After the successful completion of the work, an act of acceptance of the gas pipeline is drawn up.

Test run of the convector

After carrying out all the above measures, a test run of the gas convector is carried out. It is carried out according to the instructions attached to the installed equipment.

The gas pipeline is connected to the convector using a special type of flexible connection. Power is supplied to the unit. The "Start" command is given from the remote control. In this case, the burner is ignited and the built-in fans are turned on.

At the initial stage, the operation of the equipment may be accompanied by foreign odors. This is most commonly caused by excess paint and lubricants burning off in areas close to hot surfaces.

The stability of the installation is being monitored. During operation, there should be no smell of gas, smoke, extraneous sounds. Air supply direction is adjusted, set temperature regime.

The advantage of gas convectors is the absence of the need to build a heating system, the absence of water in the equipment. This prevents leakage and the cost of installing pipelines with heating devices. The main disadvantages are the length of the gas convector installation, the presence of hot surfaces and the possibility of leakage of natural gas.

Gas convectors are not as popular as their electric counterparts. Gas devices require a connected centralized gas supply or cylinder, and are also not as safe. But gas models cheaper to use, so they will be an excellent solution in a country house or cottage, where constant maintenance of heat in the room is not required.

What is a gas convector

It should be noted right away that the convector is not a type of boiler, it works not only according to a different principle (it does not heat the coolant, but the air in a certain room), but also has a slightly different scope. Often gas heaters used in small houses where there is no need for constant heating. They are able to heat only the room where they are installed.

What is a convector made of?

The design of the device is not too complicated, it includes:

Scheme of a standard gas convector with a fan for forced convection.

  • a heat exchanger that heats the air;
  • programmer - a device for controlling and maintaining the temperature in the room;
  • control panel with various indicators;
  • gas valve to control the gas supply;
  • a fan supplying air to the valve and heat exchanger;
  • a fan that provides forced supply of warm air into the room.

Gas convector - principle of operation

As you can see from the diagram, everything is quite simple. The convector plays a role gas burner, cold air Under the action of convection, it enters from below, heats up and exits through an opening at the top.

The device works quite simply: the principle of operation is based on the phenomenon of convection - warm air When heated, it rises and cold falls. Gas models can work both by natural convection and by forced convection. In the latter case, a special fan is used to supply air.

Advantages and disadvantages

The quality of the device itself, as well as its work, depends on the price. By choosing a cheap model, you will not save money, since the device can last you less than a year. Repair in this situation will be unprofitable. Therefore, we will consider the advantages and disadvantages based only on quality devices. So the pros:

  • efficiency and rapid heating of the room;
  • simple installation of a gas convector with your own hands;
  • there is no need to make a heating system (water);
  • low price;
  • unlike electrical counterparts, gas models do not burn oxygen;
  • fully autonomous mode of operation;
  • not tied to electricity (except convectors with forced circulation);
  • It is possible to connect the heater to a gas cylinder.

But gas convectors are not without drawbacks:

  • if gas is used centralized system, then be sure to obtain permission to connect the device;
  • it is necessary to punch holes in the wall outward where the heater will be attached;
  • considerable dimensions;
  • if you decide to install several convectors, then the gas will have to be supplied to each of them, moreover, only outside the building.

Choose models with a built-in fan. They are more efficient than their fanless counterparts.

Types of convectors

Devices can be classified by their power, as well as by execution. If everything is clear with power: choose the one that is able to heat the room, then with the types of performance, things are a little more complicated.

There are two types of heaters:

Wall models can very well fit into the interior.

  1. Floor - devices are installed on the floor, do not require special skills and abilities in installation. Such a convector can heat a rather large room (even an industrial one), but it is heavy and requires a special foundation.
  2. Wall-mounted - more compact models that fit well into the interior of the house. Often devices are mounted under a window to create thermal curtain from cold air passing through the glass. Convectors of this type have low power, so they are only suitable for heating rooms in houses up to 100 square meters.

There is another subtype of heaters - built-in. They can be installed on the floor or wall, not only do not spoil the interior, but also decorate it. In terms of parameters, such models do not differ from wall-mounted ones. But it is more difficult to install them, since it is necessary to prepare a niche for the device in advance.

When choosing a convector, you should also pay attention to the material of the heat exchanger. The latter can be made of steel, cast iron or copper. Models with a steel heat exchanger are now more common, however, cast iron ones have greater efficiency due to the properties of the alloy, and are also able to last longer. Their only drawback is their heavy weight. Copper counterparts are effective and durable, but expensive.

All considered convectors are closed. Open ones also exist, but they take the air necessary for the combustion of gas from the room, and the waste enters the general ventilation. Due to these properties, it is highly not recommended to install open-type heaters in residential premises.

How to install a gas convector

After you have chosen and bought a heater, you can proceed to the preparation of the installation. Make sure you have the following tools and materials:

Tools needed to install a gas convector.

  • drill and a set of drills;
  • pipe cutter;
  • kit wrenches and wrench;
  • scapula;
  • perforator;
  • screwdrivers;
  • sanitary and high temperature silicone;
  • dowels and screws;
  • gas cock.

When everything is ready, you need to choose the location of the convector. For correct selection use GOST. The latter requires the mandatory installation of a heater under the window. Do not be too lazy in the process to try on the device to the selected place, and also make markings after that. The next step is to prepare the premises. The room should be covered, as a large amount of dust will appear during operation.

Mounting

Technical requirements for the installation of a gas convector.

Installation is carried out according to the following plan:

  1. Determine the opening for the gas pipe inlet. Do not forget to leave a distance for summing up this very pipe and fitting.
  2. According to the diameter of the exhaust pipe, you need to drill a through hole in the wall using a perforator. This is the most difficult stage, since the hole is large, so the work will take time (depending on the wall and puncher), and a lot of dust will also appear.
  3. The next step is to drill holes for mounting the heater itself and hammer dowels into them.
  4. Now we connect to the convector exhaust pipe and make a joint with silicone (capable of withstanding high temperatures).
  5. The heater itself is fixed with screws on the wall. This is where outside help comes in handy, since the weight of the device is considerable.

Be sure to seal any holes with foam so that cold air does not enter the room from there.

Gas connection

To this stage take it very seriously. If you doubt your skills, then it is better to entrust the connection to specialists.

Mount according to the following scheme:

In accordance with GOST, the pipe must be carried out from the street.

  1. If there is a special outlet with a thread on gas pipe then it will make life easier. You just need to screw the gas valve onto the pipe. But if there is no withdrawal, then it must be done.
  2. Next, bring the pipe to the convector. It is better to use metal-plastic. The connection of the fittings must be perfect.
  3. During the laying of the pipe through each meter, it must be fixed to special clips. You also need to drill holes for this.
  4. To check the connections, you must call a gas service employee.

Remember to lubricate the fittings and pipe with silicone to ensure maximum system sealing.

Health check

Before turning on the appliance, be sure to call the gas service to check the connections for gas leaks.

After completing the installation work, it is necessary to make a test run:

  1. First of all, open the gas valve, listen to all joints for possible leaks (you can use soapy water or special device). If leaks are found, close the faucet and fix them.
  2. After checking all joints, start the convector. During start-up, hold down the button for a minute so that the gas enters the combustion chamber.
  3. After the burner ignites, adjust the operation of the appliance.

Installing a gas convector in wooden house does not differ from installation in any other building. Flammable elements are located inside the convector.

Finally

Although gas convector is not a very popular means of heating, yet we can say with confidence that it justifies its cost and the effort spent on its installation. Such a device will the best option for a country house where you come to rest in winter. The heater is able to heat the air in the room very quickly., it is more economical than its electric counterpart, and can also be powered by a gas cylinder. Perhaps the only significant drawback of the device is that it heats only one room, and not all rooms, as a boiler with a heating system does.

Video



Convection is the natural circulation of air masses as a result of heating. The principle of convection is used by several models of heating equipment. Among the modifications, the gas convector stands out especially - what it is, what advantages the heater device has.

How does a gas convector work?

Gas heating convectors for heating residential premises use the principle of natural air convection. Cold air masses are always at the bottom of the room. When heated, air rises until it cools. The principle of operation of all convectors is based on the natural circulation of air masses.

The principle of operation of convectors

The gas heating appliance works as follows:
  1. Inside the convector there is a heat exchanger connected to the convection channels.
  2. The heat exchanger heats up when the gas is burned.
  3. Air passes through the heating element and heats up.
  4. Heated air flows into the room.
The principle of operation of a gas convector has several advantages that distinguish the heating device from analogues.

Advantages of gas convectors

The principle of operation used by convection heaters has several advantages:
  • Less gas consumption- the air in the room is heated directly, and not due to the heat carrier, which increases the efficiency of the equipment and reduces heating costs.
  • No need for coolant. The space is heated by air heating. Convectors can be installed in unheated rooms, starting only when necessary, without fear of freezing of the heating system. For this reason, installing a gas convector for a summer residence is the best option.
  • Versatility– the heater is connected to the central gas pipeline or cylinders. For operation of the convector, connection to the exhaust pipe of combustion products is required.
    Connection to the power supply network is required only for convector models with a fan. The fan speeds up the circulation of air and several times increases the rate of heating the room.

To install a gas heating convector in an apartment, you need to obtain permission from the gas service and prepare a heating project, the same as for a hot water boiler.

Types of gas convectors

To choose a suitable convector, you should learn about the main differences between existing equipment, the pros and cons of modifications.

How can heaters be classified?

The cost of a gas convector depends on the material of the heat exchanger, the availability of an adapter kit, as well as the characteristics of the control unit.

Is it possible to put a convector in a residential area

Heating a house or apartment with gas convectors is completely safe. In doing so, several aspects must be taken into account:
  • Models with a vertical chimney, equipped with an open combustion chamber. The operation of convectors of this type is permitted in private and country houses, but prohibited in multi-storey buildings. In apartments, installation of systems without a chimney is recommended.
  • It is somewhat easier to obtain permission to install a convector than to obtain documents for the operation of a gas boiler. The gas service allows the use of heaters for heating industrial and domestic buildings.

How to choose a gas convector

You should pay attention to the technical characteristics of the heaters. The best option is the choice of a convector with cast iron heat exchanger closed type and programmable control unit.

When choosing equipment, you will need to consider the following:

  • Power calculation. When heating the room, air convection is used. Therefore, heaters are only effective in limited spaces. For each room you will need to install a separate convector. The power calculation is carried out according to the formula 100 W per 1 m².
  • Housing type. For an apartment, heaters with a closed combustion chamber and the output of combustion products through a coaxial chimney are suitable. You can put any type of equipment in your house. But when installing a heater with a closed chamber, it is necessary to take care of a constant and intensive supply of fresh air.
  • Fuel type. Gas heating convector for liquefied gas it is forbidden to install in the apartment high-rise building, due to the high explosiveness of cylinders.

All convectors are initially manufactured with the ability to connect to the main gas pipeline. If you plan to connect the gas convector to the cylinder in the future, you need to purchase a special gearbox (in some modifications it is included).

Which brand of convector is better to choose

For domestic use, you can choose heaters from the following manufacturers:
  1. Karma

The power of the proposed equipment ranges from 1.5 to 10 kW, which makes it possible to heat both a small workshop and a large room up to 100 m².

How to install a convector

Installation guidelines, requirements and limitations are detailed in the instruction manual. In particular, it states:
  • Installation of a gas convector in a wooden house. During operation, the body heats up to 50-55°C. It is necessary to isolate wooden surfaces in contact with heating parts of the structure. Installation rules in a wooden house prescribe the manufacture of fire breaks in the roof.
    If a coaxial pipe is used, at the point of passage through wooden wall isolation is not required. The surface of the coaxial chimney heats up slightly, due to the special design of the burner and pipe.
  • Location from the floor. air heating country or residential building has certain features that affect the efficiency of heating. To ensure maximum performance, install the convector as close to the floor as possible. As a result of this solution, the intensity of the circulation of convection flows increases and the efficiency of the equipment increases.
  • The gas pipe is brought to the heater exclusively along the street. A shut-off valve must be installed at the connection point.

A test run is carried out in the presence of a representative of the gas service. A corresponding note is made in the convector documentation.

Which is better, a gas convector or a boiler

It all depends on specifications building and its use. The installation of the convector requires less time and material resources.

Air heating is recommended for use in country houses that are not heated in winter time of the year. During installation, there is no need to use a water circuit, it is possible to heat the building only from time to time. Even at a negative temperature in the room, you can warm up the room in 20-30 minutes.

A gas convector for a house on bottled gas is inferior to a boiler connected to the main pipeline in terms of efficiency, but surpasses in functionality. The choice of an air heater is justified in the absence of gasification. On a fully charged cylinder, the heater will operate for approximately 10 days.

The convector heats the room better and faster and spends for this less fuel, but its effectiveness is limited by the properties of convection currents. The intensity of heating decreases as obstacles appear: walls, furniture, etc.

For heating a country house or small rooms, a convector-type heater is best suited. But for residential heated houses with large rooms, it is better to install a traditional gas boiler.

One of the most rational ways The solution to the problem of heating in a small residential area is the installation of a gas convector, which is an autonomous heating device. Many are interested in what restrictions exist for the installation and operation of such heaters. Can they be installed in a city apartment or a wooden house, does it require enhanced ventilation of the room. These questions and some more, such as a list of work that you can do yourself when installing a gas convection heater, will be discussed below.

How does a gas convector work?

Any convection heating appliances, regardless of the energy carrier used, operate according to the same principle, therefore their design is somewhat similar.

There is a thin-walled metal box, which not only has a protective function, blocking access to the hot compartment where the gas burns, but also directs air flows, sucking in cold masses from below and releasing hot ones from above. For this, protective boxes have a lattice structure at the top and bottom, while the rest of the surface is solid.

Thus, the metal panel covering the "innards" of the gas convector has a relatively low temperature(up to 60-70˚С), practically not taking part in the heating process. The heating of the room occurs mainly due to the heating of the air when it passes near the hot combustion chamber, that is, due to the convection process. The low temperature of the protective panel also has the following advantages:

  • no risk of thermal injury;
  • the ability to mount on the wall with most types of its finishes;
  • can be installed in frame and wooden houses.

Heated air currents rise to the ceiling, displacing colder air down, which, having reached the floor, as it cools down, again enters the convector cavity. Thus, a kind of circulation of air flows is formed in the heated room, which ensures uniform heating even of those areas that are located far from the heater.

The internal structure of the gas convection appliance

Under the outer panel of these heaters are hidden:

  • combustion chamber, which is also a heat exchanger;
  • a complex of protective and temperature control automation;
  • coaxial pipe that goes outward from the heat exchanger-furnace.

The compartment where the gas mixed with air burns is hermetically connected to the chimney, so contact with the internal air space is excluded for serviceable devices. Thanks to this design of the combustion chamber, additional ventilation of the room is not needed.

Gas exchange occurs through a double pipe that is brought out. Hot combustion products are discharged along the inner section, while air enters the furnace along the outer perimeter. Due to such a device, the outer wall of the chimney does not heat up, so no additional fire insulation is required, even when in contact with the wall of a wooden house.

The operation of the gas convector is fully automated. With your own hands, you only need to kindle the igniter using the built-in piezoelectric element and set the desired temperature by turning the knob to a certain position.

Further, the temperature is maintained automatically in a small range (2-3˚С), which occurs by turning on / off the gas supply to the main burner. Protective automation blocks the access of the energy carrier to the furnace in such cases:

  • low gas pressure on the furnace;
  • blocking the access of oxygen to the combustion chamber;
  • mechanical blocking of the exhaust pipe.

Where is the installation of a gas convector preferred?

The disadvantage of such heaters is their ability to heat only one isolated room. Heating of two rooms is also possible, but only if they are connected by a non-closing opening (an arch, for example). If you need full heating of three or more separate rooms, you need to install one convector in each of them. Therefore, if the housing is multi-room, it would be preferable to equip a water heating system.

A gas heater on bottled gas, a convection-type device has proven itself well in conditions of small-sized housing or some auxiliary rooms. Therefore, their installation and operation are expedient in:

  • small-sized private houses, including wooden ones;
  • small apartments;
  • country houses;
  • baths.

Also, such equipment is often installed in small commercial premises or offices.

How to properly install a convector

It is not advisable to do it yourself to connect to the gas supply, since this process does not tolerate mistakes, moreover, it will lead to sanctions from the gas service. To do this, you should call the master from the specialized enterprise serving this area.

The installation of the device itself can be done by hand, saving on the services of gas workers. Moreover, the process is simple, with the exception of the time-consuming preparation of the chimney hole.

Before you install, you should correctly determine the place of its installation. Usually they try to place it under the window, but this is not necessary. If the window sill is low, the product will not fit under it, especially since in the fixed state the heater must be at least 20-25 cm from the floor and the same amount to the window sill. Therefore, it will be normal if the convector is fixed on the side of the window opening, but at the same time no closer than 30 cm to the corner of the room.

Calculating right place, you can get to work. If the product is heavy better installation do with helper:

  • The heater assembly with a coaxial pipe is applied to the place chosen for installation, and the boundaries of the hole for the chimney are marked.
  • To equip the outlet for the pipe, you will need a puncher with various nozzles. During this work, a lot of dust is generated, which should be provided for, protecting interior items from dust as much as possible. To make the outlet for the pipe more accurate, it makes sense to first drill through holes around the perimeter with a drill, and only then gouge out the excess with a “blade” nozzle. If the wall is wooden, it will be more difficult. Here the "shovel" will not help. You will have to drill solid with special drills (feathers), and then clean it with a chisel.
  • When the outlet for the pipe is ready, the protective panel is removed and the product is applied close to the wall, while the chimney is inserted into the prepared hole. Now you need to mark the attachment points, while controlling the correct position coaxial pipe. It should be located strictly horizontally or with a very slight upward slope.
  • The convector is fixed to the wall with suitable fasteners (dowels or self-tapping screws if the wall is wooden) and a decorative panel is put on.
  • The chimney is set in the correct position (you can open it with chopsticks), after which the gap between the pipe and the wall is sealed with polyurethane foam.
  • A protective cap is put on the pipe and fixed with self-tapping screws (it prevents the burner from blowing out with the wind).
  • After the foam has set, the excess is cut off, and the perimeter around the chimney is ennobled with a finishing material corresponding to the design of the facade.

That's the whole installation. The process, in fact, is not complicated, so if you have the right tool available to almost everyone. It remains to invite a specialist to connect the gas convective heater to the gas supply and make a test run of the device into operation. The convector is very convenient to use and efficient in heating, so you will definitely not be disappointed with its work.

A chimney-convector, or as it is also called an economizer, is especially relevant for stoves with low efficiency. Let's look at the principle of their work, as well as how they can be made by hand.

Scope of the chimney-convector

There are three types of convectors: water, electric and gas. Installation of a chimney-convector is required only on gas heating systems and sauna ovens.

Chimney-convectors are successfully used for an accelerated rate of heating of adjacent premises, which is carried out by taking heat flows from the gases leaving through the smoke. In addition, they serve as a protective mechanism against infrared radiation, which comes from chimney. They are easy to install. They are also easy to operate. If the design is simple and without a fan, then the presence of electrical wiring is not required.

The chimney-convector can be mounted in two ways:

  • connecting the pipe to a common chimney;
  • arrangement of its own smoke exhaust system.

Advice! The second method will allow you to heat two rooms at the same time. For example, a convector is installed in one room, and a chimney is installed in another. Such a system is ideal for a bath with a relaxation room.

The principle of operation of the convector

It lies in the fact that heat transfer occurs by convection currents, which form convectors. In fact, this is a constant circulation of air flows through the case or closed cell, which occurs from the bottom up, due to the fact that cold air is heavier than hot air. Combustion products are emitted into the chimney of the convector.

The chimney for the furnace is most often made of metal pipes. You can mount the structure on your own without the involvement of specialists. It is necessary to correctly calculate the length and height of the chimney, assemble the chimney and insulate it with high quality.

The coaxial design of such a chimney consists of two pipes:

In the center is a chimney pipe, around it are air pockets, passing through which the air is heated:

  • the first is central. It is designed to discharge combustion products into the environment;
  • second. It is an external circuit designed to capture cold air. It is he who prevents the system from heating up to significant temperatures.

Read also information about on our website.

Advice! Converter chimneys are suitable for operation even in cold winters, so it can be safely installed in the system. It is only necessary when choosing to focus on models that have a rather large clearance of the chimney.

The second design option could be:

It involves smoke from the chimney and water in the barrel, which circulates after heating through the pipes

  • the central pipe is made similarly to the first variant and is connected to a gas heating furnace;
  • the second is made in the form of a barrel surrounding it, with two pipes for water circulation. Water is heated from the chimney pipe and heats the room.

Chimney-economizers are safe for indoor installation. Since it is arranged according to the type of coaxial pipe, it can be installed in the walls of the room, the material of which is wood. Read more about and bookmark the article.

Do-it-yourself converter chimney

Gas converter chimneys have a simple device, they can be made by hand.

At its core, the convector is a large-diameter pipe with pockets welded on it, which can be made of pipes of a smaller diameter, a rectangular metal profile or metal plates.

Metal chimney converter

To make an iron converter chimney is within the power of those who know how to use a welding machine.

Step-by-step instruction:

  • Step 1. You should take a pipe with a diameter similar to that coming out of the furnace (usually it is at least 15 centimeters) and cut it to the length of the chimney. On average, it is 55 centimeters.

  • Step 2. You need to take a pipe with a diameter of 5-7 centimeters and cut it into 6 parts, 45 centimeters in size.

  • Step 3. Weld 6-8 of the resulting blanks to the main one. They should form a complete circle around it.

  • Step 4. The chimney convector is ready.

  • Step 5 Connect it to the pipes.

Advice! After the converter is ready, for better heating it should be painted black, and for an aesthetic look it can be covered with some interesting overlay made of metal or galvanized sheet.

Chimney convector made of stainless steel

Stages of creation:

  • Step 1. You need to purchase a stainless thick chimney pipe and a sheet.

  • Step 2 Using rivets, attach a stainless steel sheet to the main pipe in large waves.

  • Step 3. The convector is ready.

Ready-made model of a chimney convector for a pipe, made of stainless steel