Front panels with a heater. Warm facade panels: advantages, types, installation technology Insulated wall panels for exterior decoration

14.03.2020

Heat-saving cladding panels for exterior finish facades perform the function of a finishing material together with the insulation of the room. Using them is much more economical than purchasing conventional panels and insulation separately.

The structure of all thermal insulation panels is the same. A two- or three-layer plate has a base - a heater, which is used as foam plastic, mineral wool. On top of the insulation is covered with a protective layer. With front side facade panels with a heater are covered with a decorative layer. The most popular are heat-saving plates made to look like brick, stone, clinker tiles.

Types of facade panels for finishing the house outside.

Panels with insulation are produced in the form of blocks that are installed on the facade without mounting the crate. The thickness of the products ranges from 6–12 cm. In addition to the finishing layer and the material that provides thermal insulation, they can make a hard layer and built-in fasteners at the bottom.

As a decorating surface use:

clinker, glazed or porcelain tiles with marble chips for grouting;
corrugated board with a pattern of natural materials or metal samples made of aluminum;
wood chips;
imitation stone or marble.

Attention: for the convenience of facing the corners, special elements are produced for them, which are chosen the same as the main wall, or beautifully stand out in a different shade.

Finishing the house with sandwich panels.

These are three-layer panels for warming the facade of the house, which include insulation and facing coating on both sides. As a finish, manufacturers use shavings or metal samples. Such panels need additional coverage, as they do not look presentable. From such panels, they can completely build new houses or insulate existing ones.

Facade insulated panels for exterior decoration of the house with sandwich panels can be described as light, durable, heat-saving. They are produced by pressing the insulation and outer skin. The dimensions of such panels are 12 cm wide, 1–12 m long, 0.5–2.5 cm thick. Installation is facilitated by the presence of special locks.

Thermal panel trim.

They are also durable, have a service life of up to 50 years. It cannot be used as a heater in a facade tile with a heater. mineral wool. Available in different thicknesses - 6–8 cm, so be guided by the climate of the place where the house is located to choose.

The optimal thickness of the panels will prevent the destruction of the house due to negative environmental factors or biological impact. Their main plus is ease of maintenance, because brick-like panels do not require much attention and low price compared to the cost of natural bricks.

Thermopanel with plaster for exterior decoration of the facade of the house.

Panels for the facade that look like plaster are produced from a foam board as a heater and marble chips of 0.4–0.5 cm. Their thickness varies between 5–10 cm.

Thanks to the structure, insulated Wall panels successfully withstand aggressive environments and adhere to exterior walls using conventional foam adhesive.

There are two similar ways to install panels that end with grouting:

Standard grout with marble chips to match the sample.
By gluing pieces of the profile to the sealant.

Advantages and disadvantages of facade insulated panels.

The facade panel has an important advantage - it is the ability to give the facade of any building the appearance of an aesthetically perfect brickwork. All seams are clearly defined and represent a geometrically verified pattern; it is almost impossible to create such a pattern with a simple facing brick. Also, when using thermal panels, there is no need for a painstaking choice of shades of brick or stone.

If there are advantages, then there are disadvantages. You can install warm panels only on surfaces that have a perfect even coating.

The next factor can not be considered a disadvantage. Insulated facade panels have a high price. But in the future, you can save on something else. In most cases, the high cost of the goods indicates the high quality of the material.

Do not leave a large space between the wall and the thermal panels, as this can lead to condensation.

Conclusion.

Many developers and people who are puzzled by the external repair of the house carefully choose facing materials that meet their requirements for appearance and performance. In this regard, facade insulated panels for home insulation - great choice, allowing you to "kill two birds with one stone": solve the problem with thermal insulation and transform the house beyond recognition in a matter of days.

The following two tabs change content below.

And this is not an exaggeration at all. Indeed, it is the panels for interior decoration houses largely determine its interior. You can, of course, close all the walls with furniture and the same mirrors, but real comfort is unthinkable without the use of panels.

The choice of this material is quite large, its representatives are very different from each other, there are kings and apprentices in this world, this is some difficulty - the choice, of course. But the attitude of many people practically coincides one to one, regardless of their significance.

The most important element of interior design

It is not at all accidental, because they:

help to significantly speed up the entire process of wall finishing - some panels have an area of 2-3 square meters, which closes in one fell swoop;
get rid of the careful and time-consuming finishing of the rough surface of the wall;
provide additional opportunities for hydro and thermal insulation;
have such a large number of varieties and design proposals that you can always pick up, and far from “something”, for any design of the floor, walls, for any furniture and fittings.

Classification

A large number of proposals makes it necessary to classify the material presented in the first place.

In appearance, but you can say a little differently - according to the ratio of length to width - they are divided into:

rack - here the most famous representative is the old wooden lining, its promoted "fellow analogue" with a rounded profile - newfangled plastic analogues; another thing is that the installation can now be carried out not only horizontally, but also vertically, and the width of the panels can vary from edge to edge from 10-20 cm to 40-50, and this is with a length of 2 to 6 meters; we will also include three-dimensional options from fiber cement and laminate to this class;
tiled - we can say that it is; here the size of 50 by 50 will probably be the minimum; often options are 80 by 80 or 90 by 100 - in any case, this species tries to be as close as possible to the "square"; the main advantage of the tile is preserved here too - the creativity of the independent invention of the drawing on the wall remains available to you;
sheet - such panels have the largest dimensions, 2 by 3 meters, a meter by two; such dimensions force us to look for other methods of fastening - ordinary light clamps are rarely used here, nails and special glue are already in use.

According to the material of the panel can be:

wooden - big class, which includes both natural wood and chipboard and fiber boards (chipboard and fiberboard); already the walls of the house outside the city, in nature, you will definitely decorate for real natural material, to which, however, it is necessary to present increased requirements for drying and processing; this applies primarily to lining and block-house, and processing is also required and environmentally impeccable;
plastic - a material that has found a place for itself in almost all areas of construction, thanks to its unpretentiousness, great variety and relatively low price relative to competitors;

glass - not yet fully appreciated material that can often be seen in kitchens, but it also boldly invades other rooms, perhaps not as an independent, main component of the interior, but as a very good addition and zest;
metal - aluminum dominates here; perhaps metal as an interior finish causes distrust, but the fact is that the vast majority of amazing three-dimensional panels are based on metal, and this radically changes the attitude towards this type.

Helpful advice!
We advise you to keep in mind that there are also gypsum and leather panels on the market.
The former use the ability of the material to take on any look and color at the request of the designer, hence their undoubted advantage.
And the latter can well support the corresponding interior.

Mounting

Ways

Several technologies are used for mounting panels:

Firstly, the most common is the mounting technology on the crate. Its main advantage is the ability to simultaneously carry out insulation and protection from moisture of the rough surface. In addition, we are relieved of the need for careful finishing of the original wall.
Secondly, the panels can simply be "planted" on glue, although it is special. This is much faster, but you can’t do without good wall preparation. It is also very important to use a special glue for interior spaces, which means that it does not raise any questions from the point of view of ecology.
Thirdly, the usual installation on nails. It’s even simpler, but let’s say right away that ordinary iron nails are not allowed here. It is necessary to use only the fasteners included in the kit of the panels themselves, and they must be used strictly according to the technology.

Working with a crate

The crate refers to auxiliary wooden slats, which are pre-mounted vertically or horizontally on the wall. The panels themselves are already applied to these rails.

The size of the lathing laths can vary depending on the fastening of the panels and the additional purposes of decorating the wall - if it is also insulated, then it is best to make the lathing higher, and choose the laths themselves thicker.

It will act as follows:

carefully prepare the working surface of the wall, putty all the dents, clean all the potholes, be sure to completely dry the entire area;

Helpful advice!
We advise you to pay close attention to drying the draft wall.
Here it is better to play it safe once again and wait not 10-12 hours, but a day or two.
In addition, always strive to comply with the requirements of SNiP for the slope of the surface - it should not be more than 8 mm between any two points at a distance of 4 meters.
Potholes larger than 2 mm are also not allowed, checked with a 2-meter-long rail-rule.

we lay waterproofing on the prepared surface, try to use a single sheet over the entire area;
then the crate is attached - wooden, and more often recently from a metal profile;
between the crate there are insulation plates - foam plastic is usually used, but it can also be recommended from mineral wool on a basalt basis;
if the plans initially had intentions to insulate, then the distance between the lathing slats had to be chosen a little less than the size of the insulation boards so that they fit with an interference fit, but without creating additional tension on the laths “left-right”;
we already mount panels on the rails in accordance with the technology, which directly depends on the specifics of the panels used.

findings

The subject under consideration is so multifaceted and has so many nuances that one cannot do without auxiliary introductory materials:

Be sure to check out the additional video in this article.
Make up a system of available offers from suppliers' promotional materials.
Model several possible finishes.

Only after such a scrupulous approach will it be possible to stop in your choice on something really worthwhile.

Insulated cladding panels - a universal facade material

To increase the thermal insulation of the house and give it a solid appearance, you need to do a lot of work on the installation of insulation and the installation of a decorative coating. However, both material costs and labor costs can be significantly reduced by using special materials - insulation panels with cladding.
Their installation is faster and easier than a phased finish, and the effect is the same.

The principle of the structure of all such materials is the same - these are two-layer or three-layer panels, the basis of which is insulation (polystyrene, mineral wool, expanded polystyrene, etc.), covered on the front side with a decorative layer.
Most popular materials:

Thermal panels with clinker tiles. They are different both in appearance and design.
The simplest are two-layer panels for cladding with insulation, in which cladding tiles are glued onto a polyurethane foam board. There are three-layer panels with a load-bearing bottom layer of OSB, which gives them rigidity, as well as panels with metal inserts pressed into them or molded plastic bushings to facilitate installation.

Expanded polystyrene panels with a decorative layer of plaster with colored marble chips. Their use allows you to create a seamless surface.

Metal sandwich panels are a "pie", the filling of which is a heater, closed on both sides with painted aluminum sheets or corrugated board with a protective film. A pattern can be applied under the film, creating an imitation of popular facing materials - wood, stone, brickwork.

For reference. Oriented strand board (OSB) SIP panels can also be used for thermal insulation and cladding. But they require additional face finishing.

Features of using insulated panels

The described materials are suitable not only for finishing newly erected buildings, but also for the restoration of old and dilapidated buildings. For their installation, it is not necessary to strengthen or level the facade - it is enough to fix the crate on it.
And thanks to the low weight of the products and the well-thought-out design, it is easy to do the lining with your own hands without the involvement of specialists and lifting equipment. But this is not their only merit.

Advantages of thermal panels

Among the many advantages that thermal panels of any type have, the following should be highlighted:

Reducing the cost of winter heating and summer air conditioning of insulated buildings by up to 40%. The rather high price of cladding pays off within a few seasons, while the microclimate inside the house becomes much more comfortable.
Light weight not only facilitates installation, but also allows you to transform appearance buildings without creating a critical load on the foundation, which is very important for existing buildings.

Note. Weight of panels covered with clinker tiles or artificial stone depends on the thickness of the decorative layer. Before choosing a material for the restoration of the facade of an old building, it is necessary to make sure that its foundation can withstand the load created by its weight.

Regardless of the type of decorative coating, insulation and cladding panels are highly resistant to external influences such as ultraviolet radiation, precipitation, temperature changes and its critical negative and positive values, chemical and mechanical damage.
Durability, reliability, long service life without the need for repair.
Fire resistance.
Environmental safety of the materials used.
Possibility of installation under any weather conditions.

Finally, for the consumer great importance and a huge range of insulated panels, the ability to choose decor that matches the style of the house, choose the desired color and texture, “change” the house into brick, stone, wood.

Several variants color solutions brick-like panels

If you watch the video, you will see for yourself how easy this dressing is, and how the appearance of the building is radically transformed.

disadvantages

There are not so many of them, but when choosing any material, you need to be aware of the disadvantages that it has so that they do not become an unpleasant surprise during installation or operation.
We will not rank the high cost of insulated panels as a disadvantage. Firstly, the range of prices depending on their type is quite significant, and secondly, you are unlikely to be able to save money by purchasing insulation and cladding separately and paying for the installation of each of them.
A significant disadvantage of two-layer panels can be considered their susceptibility to deformation during storage, which complicates installation. Since both layers have different density, structure and response to changes in the parameters of the external environment, the product may warp.
In this regard, three-layer cladding panels with insulation are more reliable, they do not have such a disadvantage, but they are also more expensive.
Inexpensive panels imitating brickwork, after installation, need to be grouted with special compounds that protect the insulation from destruction. This is a rather time-consuming and labor-intensive work, but it can be avoided if you buy facing boards with seams already worn out in production.

Such panels need grouting while masking the attachment points.

Mounting Features

If the walls of the house are relatively even, the panels can be attached directly to them, leveling small irregularities with linings made of plywood or other materials during the installation process. Before it starts, the most convex point is determined, and in accordance with it, on the wall using polyurethane foam beacons are fixed.
This is quite dreary and long, it is easier to immediately install the leveling crate. In addition, it will allow you to create a ventilated space under the lining, excluding the accumulation of moisture in the insulation, and facilitate installation.
It differs slightly depending on the type and design features panels, but the general instructions are:

Along the entire perimeter of the building, a lower horizontal line is beaten off, from which the cladding will begin from the bottom up;
If the installation starts above the plinth, then a plinth profile is mounted on it, which serves as a support for the panels and drains the precipitation flowing down the walls;
A crate of dry, treated with antifungal impregnation bars is attached to the wall. The distance between them must correspond to the parameters of the panels;

Important! When mounting the frame, it is necessary to carefully monitor the level, ensuring that all the guides lie in the same vertical plane.

Installation of panels is carried out from the bottom up from the corner. If there are corner elements, they are first attached. If not, the ends of the panels are sawn for joining at an angle of 45 degrees;

Fastening to a wooden crate is done with self-tapping screws, to a brick or concrete wall- dowel-nails. The length of the fastener should be 4-5 cm more than the thickness of the cladding;
Each subsequent after the first row is mounted in such a way that the vertical seams are displaced. To do this, use additional or cut-to-length panels. The front part of the panel is sawn with a grinder with a disk corresponding to the material, while the insulation is easily cut with a knife;
If grouting is necessary, this work is best done in dry weather at a positive air temperature.

Most panels are hidden. If this is not the case, the mounting holes are best made in the seams between the decorative elements, and then masked with a suitable color composition recommended by the manufacturer.

Conclusion

Many developers and people who are puzzled by the external repair of a house carefully choose facing materials that meet their requirements for appearance and performance. In this regard, the insulated cladding panel is an excellent choice that allows you to “kill two birds with one stone”: solve the problem with thermal insulation and transform the house beyond recognition in a matter of days.

Facade heat panels are a structure that serves two purposes, the first is a decorative finish of buildings, and the second is heat-saving. At present, heat panels are the best material, combining these two important components, they are also popular due to the low cost of work and a simple design that allows you to easily and quickly carry out installation work.

This article will give a description of this material, will also discuss its pros and cons. And a detailed algorithm of actions for the installation of facade panels with insulation will be given.

Since the main purpose of thermal panels is to insulate the facade, they include a polystyrene base and clinker tiles that imitate a pattern stylized as a stone or brick. The clinker coating itself is very resistant to the adverse effects of natural aggressors; in its composition it has shale clay, which is subjected to high-temperature processing.

The composition of the clinker does not contain harmful substances, so experts refer it to environmentally friendly materials, it is distinguished by high mechanical strength, excellent frost resistance, as well as heat and noise-absorbing properties. Due to these qualities, this material can also be used for interior cladding. Another type of thermal panels is a slab covered with porcelain stoneware. It is distinguished by a special surface that imitates a natural stone.

Thermal panel for cladding

These heaters are different large sizes and are used on the facades of houses made in Mediterranean or Scandinavian design. The size of the base insulation varies from six and a half to nine centimeters, and the tile itself can reach two centimeters, these dimensions vary depending on the manufacturer of the facade heat panel.

The expanded polystyrene used in this case is a foamed polystyrene, and not a regular, compressed granular one. This type of material has a number of advantages, it is denser, and has an exceptionally low heat conductivity.

Thermal panel scheme

A house lined with such panels is a noble, refined structure, and its owner can hope for many flattering reviews. Many European governments encourage their citizens to use this type of facade panels for cladding their homes.

Advantages of facade panels with insulation

But the main distinctive feature panels is their ability to provide reliable protection in the way of heat. After all, according to various studies, buildings that do not have a certain thermal insulation protection lose up to about forty-five percent of heat through the facade walls. This is a very large indicator, but a house sheathed with expanded polystyrene-based heat-insulating panels will always be a place of excellent microclimate, both in winter, when it will not lose precious heat, and in summer, when it will not allow heat to enter your house.

As we said above, maintaining the necessary microclimate in buildings is truly expensive pleasure. In the cold and hot seasons, significant financial resources are spent on maintaining comfortable temperature in residential premises. But the use of heat-saving facade panels helps to significantly reduce the financial resources spent on maintaining the house.

Lined panels, by virtue of their design, are an excellent protection against atmospheric precipitation. What is the reason for this component of the product? Thermal panels have edges that are stacked on top of each other during the installation of the plates, representing a monolithic structure that does not have holes or slots through which moisture can penetrate.

Types of panels for the house

The house, which is lined with heat panels, is a corner of comfort and a healthy climate. Since the good insulating ability of this type of facade panels prevents the appearance of mold, fungi and dampness.

Maintaining the ideal temperature in the house at any time of the year, heat panels create a comfortable climate in the premises, which, moreover, does not require constant financial injections, because this type of facade panels does not require constant maintenance or repair.

The service life of thermal panels is approximately 50 years, during which time their original color and appearance is preserved.

To install facade panels with insulation, it is not necessary to additionally strengthen the base of the house (foundation). Absolutely any base is suitable for mounting thermal panels, be it old or new. The advantage is also that all the installation work can be done by hand.

Disadvantages of facade panels with insulation

If there are advantages, then there are disadvantages. You can install warm panels only on surfaces that have a perfect even coating.

Installation on an uneven surface can lead to the gradual destruction of the insulated panels.

Do not leave a large space between the wall and the thermal panels, as this can lead to condensation.

Installation

Installation work on the installation of facade thermal panels is relatively quick and not particularly difficult. All work can be done by hand.

When preparing organizational work, there is no need to make changes to the design of the foundation or facade of buildings. It also saves significant money that would go to the purchase or rental scaffolding with other types of facade design.

When mounting and installing thermal panels, there is no need to involve highly qualified workers, if there is the necessary time, these works can be carried out independently, for this you will need:

A set of tools: an electric drill, a hammer, a construction knife and a set of screwdrivers.
Sheets of panels are joined to each other thanks to the tongue-and-groove type of connection, which allows them to be easily and quickly assembled, forming a dense structure.
Panel sheets can be installed both on metal and wooden battens and even directly on the facade walls of the building. In this case, the wooden frame should have dimensions of 50 millimeters by 50 millimeters, which will contribute to its stability.
You can fasten the heat panels with screws, while the cap size should be 10 millimeters or a little more.
The wood that will be used to mount the frame must be pre-treated with fire and antifungal solutions. wooden frame mounted on the wall using metal corners, the distance between them is 750 millimeters.
When using a metal frame, the heat panels are attached using clips, the use of which creates the effect of inconspicuous mounting, while the distance between the heat panel fastening posts depends on the size of the panels themselves.
If the installation of heat panels is carried out on the facade wall without installing a frame, then when installing in places of irregularities, it is necessary to use beacons. Panels can be fixed with dowels or special screws.

It is also important to remember that the gap between the wall and the heat panel, if any, is best filled with mounting foam in order to prevent air movement, which will further weaken the entire structure.

The basis for the installation of facade heat panels can be brick, stone, concrete, wooden wall, as well as installation is possible on the "sandwich" panel.

Also, a great advantage of this type of panels is that it is possible to install them at any time of the year and with your own hands, but it is good to grout the seam surfaces at temperatures above zero.

Conclusion

Today, thanks to various technologies, all construction work you can do it yourself, that is, with your own hands.

When using this material, your home acquires unique style. Although the wall panels are large enough, their mass is very small. Thanks to this, all installation and other work can be done completely independently.

You do not have to hire professionals and specialists to carry out this work. During installation, you will need a small number of tools. Before installing heating panels, do not forget to carry out a series of preparatory work. The surface of your home should be clean and smooth.

A person is greeted by “clothes”, and a house is greeted by its facade. Since you are looking for information about facade panels with insulation, it is clear that you are not indifferent to the appearance of your home. However, if the thermal panels:

other benefits besides beauty?
What, in general, are thermal panels?
How are they produced?
How to mount them?

Everything in order in the article and two additional videos in the middle.

Although panels for insulating the facade of a house are something new for the CIS countries, in Europe the first houses with such insulation appeared more than 50 years ago. Such a difference in the markets is not surprising, given the higher cost of warm panels. In a sense, they can be called a semi-finished product. And, as you know, any semi-finished product costs more than cooking on your own.

In a sense, the panels can be called a semi-finished product

What is a sandwich and how is it eaten?

Facade panels for the exterior of a house are inherently a “sandwich”, which consists of two or three layers:

Decorative facing layer;
insulation;
Internal base.

Most often in the domestic market there are clinker panels for the facade. This type of insulation system is a layer of expanded polystyrene or polyurethane foam into which clinker tiles are recessed during the production process. Clinker is a durable clay material that is made at temperatures over 1000 degrees Celsius.

Clinker is a durable clay material

For the sake of justice, it is worth saying that there are also panels covered with metal and decorative plaster. Why was this type of insulation a little higher called a semi-finished product? For example, because a person himself can cover the wall with foam plastic and stick clinker tiles on it. However, this approach will require much more time, and the results will be very different in aesthetic properties.

Facade panels under brick by foaming polystyrene foam or polyurethane foam (polyurethane foam), and then, under pressure, as it were, soldered clinker tiles into the mass. The result is a durable facade element. To tear off the tiles, you need to apply a force of 300 kg. Hands will be very difficult. Although, for the sake of fairness, it is worth saying that even a damaged panel element can be easily restored using mounting foam. You need to buy a suitable clinker tile (or use the one that has fallen off and apply a small layer of foam to the tile and to the place where it should be glued. Then carefully attach the tile to its original position. Below we will discuss three disadvantages of thermal panels. But, since one of them is related to the installation, this issue will be discussed in the appropriate section.

Is there an alternative?

Yes. Clinker tiles often imitate brick, but someone will say why imitate? You can use clinker bricks as a finish, but this one is suitable, it has at least two drawbacks:

Price. If you consider an expensive panel with insulation, believe me, brick cladding will be much more expensive;
For a brick you need to build separate foundation , and this additional time, forces and means.

Have you chosen? Mounting?

Insulated facade panels sit on the adhesive mixture or guides. But, before that, it is necessary to wipe the side edges of the panel with a brush. This is done for better grip. If you have chosen an adhesive mixture, apply it to the back of the panel, making sure that one thin layer covers the entire panel, and also in several places - in the corners and in the center, make "blunders" in accordance with the facade relief. Attach the panel to the wall and let it stand for 5-10 minutes. After the panel has frozen, you can begin to adjust. Align the panel using the horizontal and vertical levels.

You need to start installation from the corner of the bottom row, and it is worth mentioning that there are special corner panels. Carefully level them even before applying the adhesive mixture - figure it out, and only then mount it more thoroughly on the glue.

A day after shrinkage on the glue, the panels with insulation are fastened with dowels-umbrellas into pre-drilled holes between the seams.

The video below shows how the guys from one Sumy company deftly cope with the installation process:

Particularly difficult sections of the walls

In places where the panel should adjoin the window opening or bypass, say, gas pipe, you need to cut the panel. Use a grinder with a diamond wheel for this. As already mentioned, there are corner facade heat panels. In addition to ordinary and corner ones, there are also thermal panels for special conditions, for example, beveled ones, but in any case, the “semi-finished product” also needs to be fried, and in our case, we cannot do without a cutter.

Approaching the finish line

The last two stages of installation facade tiles with insulation is grout. A grout layer is applied to the entire surface and rubbed over the entire surface with a brush. It is necessary to carry out the jointing no less than a day after shrinkage to the glue (do not forget that between these two stages there is still fastening with dowels). After grouting, you need to thoroughly wash the surface with a sponge. Grouting and washing them is not a quick thing, but what to do is one of the minuses.

It is necessary to carry out the jointing of the seams one day after shrinkage on the glue

Let's sum up our review and a small instruction for the installation of slabs for facade insulation.

PROS:

Ease of installation, no wet processes;
Attractive appearance imitating brick or stone;
Good thermal insulation.

MINUSES:

Higher cost, before, say, bark beetle plaster;
The need for thorough grouting, followed by washing the solution.

If you like to experiment, why not use warm facade panels? But, it will be quite a long experiment. Wikipedia says panels last between 50 and 100 years. So that our grandchildren will probably be able to find out about the results.

How to make a panel yourself?

As already mentioned, polyurethane foam or foam plastic is used for the manufacture of facade thermal panels. And this means that if clinker tiles are glued onto foam plastic sheets, then, in fact, thermal panels are obtained. Although, the work is laborious, and it is unlikely to pay off. In addition, there is an offer on sale called "Combiterm". This is a polystyrene foam sheet, with clinker tiles already glued. Such a solution will be cheaper than a panel with PPU filler.

What do those who have tried say?

Below are three reviews of people who have already decided to use a panel with insulation as finishing material for walls:

Yuri, 60 years old:

“The house was not insulated, I asked around, got on the Internet, found a company that does the installation. From this it began, I looked at several objects, talked with people, liked it. We have a gas boiler, we burned about 350 cubic meters of gas per month. After being insulated, it turns out 250 maximum. In winter, they kept 24 degrees in the hall, 18-19 in the bedroom. Now we are reaching the same 24 degrees, but with less gas consumption. In summer, before warming, the house warmed up to 28 degrees. It's much colder now in the summer. Almost everything is pros: thermal insulation, sound insulation, and decor. Of the minuses, only mashing. Pretty boring event"

Alexey, 55 years old

“There was a question of warming the house, so I looked through a lot of information on the Internet and found about clinker panels. I had a desire not just to insulate with polystyrene, but to insulate with polystyrene and insulate with polystyrene and overlay with clinker bricks. But, for this it was necessary to make a foundation under the brick, that is, it was a lot of expenses. Therefore, given that thermal panels with clinker tiles are both warm and reliable. My house was built of foam concrete fired in half a brick with silicate brick with an air gap. And here is another 8 centimeters insulated with thermal panels. After insulation minus 100 cubic meters of gas per month consumption. Real Savings"

Andrey, 37 years old

“Before, let's say that the temperature in the house was 22-23, but the consumption was very high. Now the temperature in the house is the same, but the gas consumption is much less. One and a half times exactly. We spend 180-200 cubic meters. Again, the house was old, wooden, finished with bricks and there was a draft, a draft. Now, when insulated with thermal panels, it became warm. Before the insulation, there was no condensate, and now after the insulation it has become fine, the temperature of the house is excellent and the gas consumption is less. There are no cons, let's say, the only thing, maybe the price, but then again, if you take all the components, all these corners, this turns into pluses.