A master class on making crafts "Stork" for decorating the territory of a kindergarten. Do-it-yourself stork for the garden: three unique ways to craft from improvised materials How to make a stork from a bottle and plaster
An old legend says that God gathered all the reptiles from the Garden of Eden into one bag and ordered the man to throw him into the sea with his own hands. And the curious Homo sapiens wanted to look at the creatures, untied the bag, and, of course, missed everyone. Vladyka became angry and turned this man into a stork so that he would protect other people from all kinds of toads and snakes. Since then, storks have always settled near a person, feed on reptiles and bring us happiness.
Many old pictures depict a stork with a baby. Among the Slavic peoples, it is customary to believe that this particular bird is responsible for childbearing and well-being. If storks settled on the roof, the house will be full of happiness and children's laughter. And if you haven’t settled, then a wonderful stork with a baby can be made with your own hands from improvised material and installed on a skate or on an apple tree in the center of the garden.
bottled happiness
It will take
To make a stork out of plastic bottles for the garden, we need to prepare the following materials:
- empty bottles;
- thick wide board for the base;
- a rod or thick wire for legs;
- a piece of foam 10 cm thick;
- corrugated hose from a vacuum cleaner;
- 2 plastic canisters with a volume of 5 l;
- metal mesh for wings;
- stapler.
Master class on making happiness
It only takes a few hours of passionate DIY work to make almost real storks appear on the paths of your garden.
- Cut out a head with a beak from a piece of foam, draw eyes or glue black beads with your own hands.
- Cut out a two-piece beak from a dark bottle and glue it in place.
- We begin the master class on making the torso by cutting off the handle in the canister. Then you need to bend the mesh in the shape of a canister with your own hands and cut off the excess.
- To make the legs, bend the bar and fasten its ends to the board.
- We are holding a master class on the preparation of plastic feathers.
- We attach the feathers to the canister, starting with the tail.
- The master class on fitting the neck begins with attaching the reinforcement wire. Then a hose is put on it.
- Attach small "feathers" on the neck with tape.
- Fix the feathers on the grid.
- The stork for our garden will stand with its wings folded, so we simply fasten all the feathers with a stapler with our own hands, overlapping each previous row by a third.
- We finish the master class by connecting all the details and decorative tinting of the eyes, beak and legs. This bird can be installed with your own hands in the depths of the garden for the whole summer. It will not deteriorate from the rain and will not fly away.
Today's fashionable toys are hand-sewn from ordinary fabric according to simple patterns. We will not fully describe the master class for their manufacture.
- Cut out the details of the craft from the fabric, sew and stuff with any filler.
- Separately, you need to make a beak (can be made of cardboard) and attach to the head. It remains to make clothes, glue eyes, wrap the baby and hand it to the stork.
Of course, you cannot settle such a wet bird on the branches of the garden, but flower pot on the windowsill she can decorate.
Another way to make your home rich and happy is to make a stork on a nest. As a basis, you can take patterns of a tilde bird. Cut feathers out of plastic white milk bottles, fasten them together and make wings, decorating the ends with real feathers. Place a few white feathers on top of your head. Form a tail out of real feathers, sew or glue eyes and a tie, and plant the bird in the nest.
It can be made from ordinary rods, fastened with wire. To get a stork with a baby, put any doll in his wings. The master class on making a lucky amulet is over.
These two rag birds cannot be left on the paths of the garden, and the master class for making the first stork requires a lot of time and materials. Do not be upset and just make a nest and cut a flat bird out of textolite or plywood. Color it in, give it a string bag with a baby doll in its beak and that's it, the stork with the baby has already settled on your roof.
A beautiful and bright figure of a stork will bring a touch of grace to the backyard landscape, especially if it is made by hand. It may seem that making a stork is difficult and requires many years of practice in needlework, but the method of making it is simple and the materials are inexpensive. This sculpture would be a great addition to adjoining territory and decoration for flower beds, lawn and garden plot, symbolizing prosperity, well-being and family comfort of its owners.
How to make a stork for a summer residence with your own hands: a master class
A do-it-yourself garden stork is one of the favorite crafts of summer residents and gardeners, and there are a lot of variations of its execution on the Internet, but the manufacturing principle is approximately the same in all cases, regardless of the materials used and the richness of the decor. Read how to make beautiful wooden signs for your home.
First of all, the head, neck, torso, wing frame and legs are made, which are connected with fastening tools.
All the remaining time is devoted to a rather painstaking procedure for cutting, fringing and decorating feathers - they will make up the plumage of the body, neck and tail of the bird. There are homemade options without the use of plastic bottles, but they are less common. Let's take a closer look different variants making a stork in this article.
Materials and tools for a garden figure
The figure of a stork is made up of a head, beak, neck, torso, paws, wings and white plumage with layers of black feathers. All parts are fastened together with a furniture stapler and seated on universal glue.
The body of a stork can be cut out of wooden block desired size, foam or a 5-liter plastic canister.
- plastic bottles 1.5 and 1 l from milk;
- plastic bottles of 1.5 and 0.5 liters from kvass or beer;
- canister 5 l;
- scissors;
- glue;
- self-tapping screws;
- a piece of foam;
- corrugated tube;
- steel bars;
- frame mesh;
- thin wire;
- sandpaper;
- furniture stapler;
- red acrylic paint.
The plumage of the stork is also made from transparent bottles, but then the plastic under the feathers should first be painted with white and black acrylic paints.
Production steps from plastic bottles
Having prepared necessary materials and tools, you can start making constituent parts crafts. About beautiful wooden fences find out with your own hands.
It is important that all parts of the stork's body are proportionate to each other.
Head
With a sharp knife, the contour of the head with the beak is cut out of the foam, after which the surface is polished, and the edges of the beak are leveled with sandpaper. If desired, the head can be painted with white paint - the coating will give the future product a rich white color and create an additional barrier from the sun, wind and rain.
The beak consists of 2 plates that are attached to the head with self-tapping screws. For a beak, the neck and bottom are cut off from a dark plastic bottle, and the rest is cut into rectangular plates. Triangles are cut from the resulting blanks, which will subsequently be the upper and lower parts of the beak.
The plates are bent in the middle and screwed to the junction of the head and beak.
Paws
The paws are cut out of 2 half-liter bottles with dark walls, after cutting off their bottom. The fingers of the future bird are cut off from the very edge to the neck of the bottle - you should get 3 in front and 1 in the back, and bend outward.
Each finger is shaped into a long, sharp triangle with scissors.
Plumage
Processing blanks for feathers to give them a beautiful natural shape with feather veins is the most labor-intensive and long part of the work.
To cut feathers, the bottom and neck of the bottle are cut off, and the cylinder of the bottle is cut into 6 equal parts - 6 feathers. They will be of different sizes: for plumage of the body - small, for the tail - longer. Each feather needs to be given airiness by creating a fringed fringe around the edges. He will tell you about metal forged gazebos for giving.
Plumage on the neck can be done in 3 ways:
- cutting out even smaller plates than for the stomach, decorating them with a fringe and curling them with scissors;
- cutting off large plates to the length of the neck and serrating their edges;
- cutting off half of the bottle and making deep sharp cuts in the resulting plates.
Each pen is a rectangular plate made of a plastic bottle with a rounded or embossed edge.
frame
The body of a stork is conveniently made from a 5-liter canister, from which the handle is first cut off. Then a mesh is attached to the container, to which future feathers will be attached - it is bent and cut in the shape of a wing.
Next, you can proceed to assemble the main part of the product - a neck tube is inserted into the neck of the canister, and 2 holes are cut in the lower part, through which a long piece of a thick rod bent in half is threaded - these are paws.
The nets are fixed with wire or steel brackets on the canister.
Assembly and decoration
The stork is assembled starting from the head - it is connected with a wire to a corrugated tube and additionally fixed with hot glue.
Feathers are fixed with a stapler, starting from the bottom of the canister and then upward in layers. The tail is attached to the back of the figure. The plumage is also applied to the mesh in layers, starting from the outer edge, and fixed with wire. In this case, black feathers are located on the outer edge. You will get only about 6-7 layers of feathers. The extreme row connecting to the tube is screwed with self-tapping screws.
Prepared plates with pointed edges from half bottles are wrapped around the neck.
The number of feathers depends on the location of the wings: the option under consideration is designed for folded wings, but when flapping, the wing mesh is covered with feathers from 2 sides and the back of the stork is also made.
After assembling the bird, you can proceed to the creative design of the craft.
Eyes can be bought ready-made in stores that sell parts for knitted and sewn toys, and glued with hot glue. For plug-in eyes choose large black beads or balls. You can also draw eyes - with simple black or colored paints to your taste.
It is necessary to paint feathers, if transparent bottles were used during work, before cutting them, after wiping the surface of the coating with an alcohol solution.
The beak and legs of the product also need to be painted with red paint. Alternatively, you can wrap them with red tape.
What else can you make a stork from
Craftsmen manage to create masterpieces from everything that is lying around in the garage, including, and also use the leftovers building materials after repair. Several of these variations of garden storks can be safely taken into account - it will not be more difficult to make them than the previous version.
From polyurethane foam
In this way, you can create a garden sculpture by turning and giving the figure of a stork a realistic image. The “skeleton” of the product will be a steel frame - steel bars are welded to each other, and then other elements of the stork's body are mounted on them.
To make a stork you will need:
- 5 liter plastic bottle;
- mounting foam;
- steel bars;
- Styrofoam;
- dye;
- ground solution;
- scotch;
- rasp.
You need to put on the body-bottle on the frame, and attach the sharpened pieces of foam to each other with adhesive tape to the neck rod. Figured foam hips are fixed in the same way.
Even with the use of waterproof plywood, the possibility of soaking the sculpture in cold period year increases, so it is recommended to store it in the room before the onset of heat.
To make a stork you will need:
- plywood;
- plastic bottles with white and dark walls;
- hot glue gun;
- rods;
- jigsaw;
- self-tapping screws;
- scissors;
- screwdriver;
- furniture stapler;
- red acrylic paint.
It is advisable to apply the elements of the body and wings first on paper, creating a “pattern” of the details before cutting them out on a sheet of plywood. The wings are screwed to the body with self-tapping screws. The paws are made of steel rods and are attached with brackets to plywood sheets that act as a torso. Plywood sheets are also used for or.
Feathers are created from bottles, and each plate, in turn, is processed along the edges with scissors to obtain an airy fringe. The plumage is applied to the entire surface of the stork, starting from the back: first, black feathers are laid out, and then white, from which the tail of the bird is also created.
Each blank is sanded along the edges and the surface is primed.
- a layer of red paint is applied to the plywood beak;
- eyes can be drawn independently.
The bars of the legs can be sharpened from the bottom edge so that they easily fix the product in the soil.
Styrofoam
Styrofoam stork is a monolithic structure, lightweight and easy to manufacture.
For work you will need:
- foam sheets;
- steel bars;
- glue universal;
- scissors;
- saw;
- furniture stapler;
- sandpaper;
- Acrylic paint in black and red.
First of all, paws are made - the lower edges of 2 steel rods are sharpened, and the upper ones are bent for subsequent fixation in the foam body.
Main creative work over such a stork is to create the correct foam blanks, because the finished bird will consist entirely of it. The body, head and neck are drawn in foam and cut with a saw. Pro plastic barrels for watering at the cottage will tell.
Iron rods are fixed in the stork's body with brackets, its surface is sheathed with a layer of foam for volume, and wing blanks are glued on top. The neck and head are mounted on a rod.
The stork's beak is painted red, and it is better to make false eyes, from beads or balls - this way the figure will turn out more expressive.
Next, the final modeling of the figure is performed, giving it smooth and beautiful features with sandpaper and a knife. This is the case when you do not need to make feathers for a bird - the relief plumage can be cut directly on the body of the product, simply by accentuating the edges of the wings with black paint.
How to make a garden stork nest
The classical composition with storks in the nest traditionally symbolized cozy house with big family among the East Slavic peoples, indicated the fertility and hospitality of the owners. Installing storks in a nest on your own plot, in a flower bed, on the roof of a house or on a playground with children will help not only decorate the territory, but also show guests that the owners are jacks of all trades. About street country washbasins will tell.
Old wheels from a bicycle, cart, trailer or wheelbarrow will fit under the nest frame. You can weave a nest from a bush and live or dry branches, fixing the entire structure with steel wire and installing it on a special platform consisting of X-shaped linings.
Video
How to make a stork from plastic bottles, see this video:
Conclusion
- The most time-consuming and laborious work on a garden stork is to create its plumage - each feather must be worked on manually, giving the edges a jagged or fringed shape so that they look like natural bird feathers.
- Feathers from transparent bottles should be dyed white and black to mimic the natural plumage of a stork.
- Before painting the feathers, they must be wiped of dust and wiped with an alcohol solution so that the paint lies evenly.
- The easiest way to make a stork is to make it completely out of Styrofoam and sharpen it with a knife and rasp to the desired shape; the simplest wing without a frame is made from a piece of plywood, which is screwed to the homemade body with self-tapping screws.
- The body with the neck can be made from a plastic 5-liter canister with a cut off handle and neck, into which a corrugated tube is then inserted.
- It is also possible to make a garden sculpture from the remnants of building materials lying around after repairs, and it will cost almost free. Additionally, you will need to buy only acrylic paints in order to draw eyes and paint feathers.
Bright garden crafts made from plastic bottles are an easy and affordable way to decorate your favorite yard. The original sculpture of a stork made of durable material will update the familiar landscape and create a joyful mood. A do-it-yourself bird figure will make the garden unique and become a family symbol of kindness and happiness.
How to make a stork from plastic containers
To make such a craft, you need to stock up on free time and be creative.
My patio is adorned with a stork figurine based on a 5 liter plastic bottle covered with polyurethane foam and painted with acrylic façade dyes.
Here is such a wonderful stork obtained from a plastic bottle and polyurethane foam
What materials and tools will be needed
By creating your own bird design, you can assemble it entirely from plastic containers by fastening them with glue or staples. And you can make the sculpture more expressive by adding plastic construction wood details.
The frame of this bird is wooden, covered with plumage from plastic bottles.
Or make individual elements of foam.
You can create such an exotic collection using ordinary plastic bottles and a piece of foam.
For our crafts of impressive size, you will need:
- Canister plastic 5-liter - the basis of the body.
The 5 l canister forms the basis of the torso
- Milk plastic bottles of 1 l and 1.5 l, from which white plumage is cut. You can get by with a transparent container, but first it should be painted with white paint for outdoor use.
- Dark plastic bottles of different capacities: 3 half-liter will be needed for the manufacture of paws and beak, one and a half liter - for dark feathers.
Plastic container dark color needed for feathers, legs and beak
- Styrofoam 10 cm thick, from which the head of a stork with a beak is cut.
A bird's head is made from a piece of foam
- Sandpaper.
- Scissors.
- Corrugated tube for the neck.
A long bird's neck is made from a corrugated tube
- Metal mesh as a base for the wings.
- Furniture stapler.
- Metal rod 6–10 mm thick for the legs.
- Wire thin for fixing the wings.
With the help of wire, the wings are firmly attached to the model of the body.
- Self-tapping screws.
- Glue gun or universal glue.
Glue universal quickly glues plastic and other materials
- Acrylic facade paints, brushes.
Stages of making a stork
Having acquired tools and materials, they first prepare all the details of the bird, then assemble it.
Head
A head with a beak is cut out of the foam plastic with a sharp knife.
A bird's head is cut out of a piece of foam
Then grind the rough surface with sandpaper. You can cover the workpiece with white facade paint.
The workpiece is sanded with sandpaper to make the surface smooth.
To strengthen the beak, 2 triangular plates are used, which are made from a dark bottle of 0.5 liters. Having cut off the neck and bottom, cut along the resulting cylinder and cut out triangles. The plates are bent in half and attached to the beak with self-tapping screws.
The beak is made out with plastic, attaching it to self-tapping screws
Paws
They are made from the top of brown bottles of 0.5 liters. Containers with a cut off bottom are cut to the neck lengthwise into 4 parts, sharpened at the ends and bent outward.
Paws with fingers are cut out of dark bottles
Plumage
The most laborious and longest stage preparatory work- blanks of feathers. They will be required a large number of, of different lengths, shapes and colors: for the design of the wings and tail - long, dark and white, for the body - light smaller ones.
For crafts use light and dark feathers
The neck and bottom of the bottle are cut off, the remaining middle part is cut along and strips are cut out of the resulting rectangle. One edge of the strip is rounded. From liter bottle make 6 large feathers.
1 liter white bottle is divided into 6 parts
For plumage of the neck, small feathers are cut out and the ends are made in the form of teeth or fringe. You can decorate a long neck with large plates from halves of milk bottles, which are finely chopped around the edges.
figure frame
The body is made from a canister with a cut off handle.
A canister with a cut off handle is the body of our bird
Fine mesh is used as the base of the wings. metal mesh, which is fixed to the canister with wire or staples. The mesh along the edges is cut in the shape of a wing and bent down.
A fine-meshed mesh is fixed on the canister - the basis of the wings
A wire is inserted into the neck of the canister and bent, forming the frame of a long neck. Fasten the wire to the metal bar of the legs and put on it a corrugated tube or hose from the vacuum cleaner.
Strengthen the wire for the neck and put a hose on it
A hole is made in the lower part of the container and a bent rod is threaded into it - these will be the legs.
The legs are made of wire by bending it and threading it through the hole at the bottom of the canister
Or they pierce the canister from below and insert curved rods, on the ends of which they put the paws upside down.
Assembly of parts
After preparing all the details, the structure is assembled.
- The head is put on a wire and additionally attached to corrugated pipe glue.
- Cover the body with plumage starting from the bottom. Light feathers are fixed on the canister with brackets.
Begin to screw feathers from the lower part of the body
- They form a tail of feathers, placing them in rows and fixing them on the body with a stapler.
- Feathers are screwed with wire to the edge of the mesh wing. To make the plumage of a stork with black edging along the edges of the white wings, the first two rows are made from dark feathers.
The wings begin to be decorated with feathers from the edge, using dark-colored blanks
- Subsequent rows are formed from white feathers, overlapping them.
The third and subsequent rows on the wing are made of white feathers.
- A number of feathers are screwed at the base of the neck with self-tapping screws.
It is not difficult to make a stork with sweeping wings
In this case, the feathers are screwed onto the entire canister, and the mesh base of the wing is covered with plumage on both sides.
On spread wings, feathers are attached on both sides.
Decoration of garden sculpture
By decorating plastic craft can be made brighter, especially if only transparent bottles were used in its manufacture. For this, acrylic dyes for outdoor use are suitable. Pre plastic container wipe with an alcohol-based solution and paint over with white or black paint until the feathers are cut out.
Acrylic facade paint is moisture resistant and does not fade under the sun
The beak and paws are painted red or wrapped with red tape.
The beak and legs are painted red
Eyes are made from beads, decorative blanks for toys or small buttons that are put on glue. You can just paint them with black paint.
Acrylic paints become brighter after varnishing.
Master class on making a stork
There are many options for making a stork from plastic containers using elements made of wood, polyurethane foam, and polystyrene.
Such an original composition of the stork family in the nest is also made of plastic
Even a beginner will be able to make such a garden sculpture, guided by video footage from step by step instructions workflow.
Video: how to make a stork from plastic bottles
Storks from plastic bottles are an original decorative decoration of a personal plot and an object of universal admiration. After all, they are made from ordinary garbage, turned by skillful hands into works of art. Made of durable plastic, they are not afraid of rain and snow. Over the years, the figures will not swell, the paint will not fade or peel off.
Almost everyone has heard that storks bring babies. Yes, that's not true. But only if we consider direct meaning this omen. But legends are not born just like that, without any justification, right? And it’s not just that near maternity hospitals, on the territory of children’s institutions and on playgrounds for active games, children can often be found.
And is it only in this that the mysterious power of a beautiful bird lies? What else can a stork figurine bring to the owner’s house and why is it considered that a stork sculpture is an excellent gift for everyone to whom the donor wishes good and prosperity?
Symbolism of a bird and a figurine of a stork
A huge number of beliefs and legends are really associated with storks, which have come to us since ancient times. In ancient times, people believed in this majestic bird, considered it sacred and endowed it with great magical power. Even then, during the hunting for food, killing a stork or causing any harm was considered a very bad omen, because such an attitude towards the “deity” entailed misfortunes and even death of the culprit or members of his family, and in relation to the rest of the people led to crop problems associated with hurricanes, floods, droughts. That is why, from time immemorial, the inhabitants of many countries protected storks, rescued them, helped build nests, and every spring they waited for their return.
By the way, the stork was not immediately called a stork, and there is no authentic version of how and why the bird got its name. In Old Russian, Slavic, Sanskrit, German indeed there are consonant words, but that is why it is so difficult to establish the truth. To date, the version that the name “stork” comes from the German magpie “Heister” sounds most plausible, and the word first sounded like “geister” and much later became what we hear now. And, again, in different regions of the countries of the post-Soviet space, you can hear other names for the same bird: busel, chornoguz, leleka, busko, botsyun, toad-eater, etc.
Pagan beliefs show that people in ancient times firmly believed that the white stork carries the souls of people who later "turn" into newborns. Probably, it was from here that the proverb came about that storks bring babies, but not in a literal sense, but only play the role of an intermediary between God and people, helping souls come to earth.
They say that the first figurines of a stork were also created in order to protect from evil spirits and evil spirits, from bad weather and lightning into the house. Besides, in different countries they were considered helpers of the gods: in Rome - Juno (motherhood), in Greece - Hera (nurse), in Germany - Holda (awakening of nature), in the Baltic - Potrimpos (spring), etc.
And, of course, the sculpture of a stork symbolizes the love of children for their parents. In ancient times, the Romans and Greeks were sure that the grown-up babies of storks take care of their elderly parents and get them food. Then even the "Stork Law" appeared, which prescribed the care of parents until the end of their days.
These birds are the key to family happiness, because they always break into pairs, incubate eggs in turn and take care of the babies together, and after a forced flight for the winter they return to their nests. To this day, storks are the only birds that never leave their family, because even after the chicks have become adults, they try to stay somewhere nearby.
Why are garden figures of storks so popular in Ukraine?
If we turn again to the legends, we can recall the legend that tells how storks brought bunches of grapes to the Cossacks in a Tatar prison so that they would not die of starvation. And yes, this is what saved the Ukrainians, who were subsequently released from captivity. The legends of Moldova, where the stork became a symbol of viticulture, speak of a similar case in the distant past.
It's hard to tell if this is actually true or fiction. But the fact that they are very popular not only in Ukraine, but also in the neighboring countries is a fact. Such garden decor more and more often you can see not only near some institutions, but also in the courtyards of your own houses, in summer cottages, in cities and remote villages. A well-groomed and interestingly designed area always contributes to the creation of a cozy, comfortable and peaceful environment, and if it is also a bird that brings happiness and joy to the owner, if it is beautiful and gives the site a special chic and individuality ...
At the same time, unlike most polymer garden figures, each future owner decides for himself how best to install the statue: on the ground or on the roof of the house, buy storks in a nest for the garden or make it with your own hands, opt for a single bird, a couple, a family of storks or more like a traditional stork with a baby. Here, as they say, to each his own, and you can give free rein to your imagination, solving not only the aesthetic problems of the exterior of the house, but also, perhaps, realizing your personal dreams and desires in reality.
Where can I install the figure of a stork?
They can be installed anywhere and look great everywhere. The ideal option is lawns and flower beds, especially if you have a stork with a child. A figurine of a stork with a baby can also be installed in a nest on the roof of a house or a tree, if he holds a bundle in his beak and stands on straightened legs, because in a sitting position the bird simply will not be visible.
Paired garden storks can also be both in a nest on a hill and on the ground. But where there are several of them, for example, a whole family of parents and children, can only be placed on the ground, since it will be a little ridiculous to look at the roof of the house, “dotted” with a large number of large birds.
Now a few words about how you can install a decorative stork and where it is better to put a nest, if it will be used. In nature, storks can build their nests not only on high ground, but also on stumps, even in thickets on the ground. Therefore, if you decide, for example, to cut down an old tree, then you can leave a stump slightly above the average height of a person and install it there. This material is light enough to be installed "in all winds" with reliable fastening and at the same time not subject to negative environmental factors such as snow, rain or temperature fluctuations.
If there is no desire to raise somewhere at all, then you can choose a place for it on the surface of the earth, but in order to give it some naturalness, it is advisable to choose slightly shaded places and place it next to shrubs or lush green vegetation.
And, of course, they can also be used for home decor if they are installed on the roof or a nearby pole. They always look amazing, and from a distance it will seem that they are actually alive.
How to make a decorative stork nest
This interesting and very unpretentious piece of decor for the garden is quite simple to make, and special skills are not required for this. Yes, if you want to make it really beautiful and reliable, you will have to spend a little time, especially if you want to give it the most natural look. But it's worth it. And, of course, it will look much more interesting than the finished composition of a stork in a nest bought in a store, because “live” branches will be used here, and a few drops of light gray paint on the nest itself will help to give even more naturalness. The painstaking work is to collect, cut and lay out the branches, but when the process begins, such a pastime will give a lot of pleasure and allow creativity to manifest.
For the base, you can take any non-heavy trough, basin or other container, which will subsequently be framed with twigs. It is advisable not to take old tree branches, because during the laying process they will break or they will have to be screwed with self-tapping screws. If you take something younger and bending, it will be much easier to work, and such branches can simply be tied together, sometimes making attachments to the base.
In addition, you can buy a ready-made one and wind the vine on it, giving completeness and naturalness. What is convenient in this option? The fact that in this basis there were initially rings into which the legs of a standing man are attached. This is perfect option for placing a stork's nest on a roof or other elevation, because it is reliable and ergonomic, in addition, it is possible to strengthen the mount, if not just insert metal leg in the ring, but also to weld.
Now about where you can place a decorative nest for a stork and how to fix it so that the design is preserved for a long time.
- Roofs. Suitable for almost any gable roofs houses, garages, outbuildings, gazebos, on which a solid platform is installed (X-shaped lining connected by a board). You can fix the structure on the rafters using self-tapping screws or nails. flat roof not even worth considering, because the nest will not be visible, but if the goal is exclusively a stork figurine, then you can try.
- High stumps, trees. This is just the case when you can not cut down the old tree to the end, but use it as a stunning decor for the garden, making it the main focus of the entire site design. Here garden figure the stork in the nest will look just great and will become the best decoration. Also, here you can place a standing garden figurine, if you attach the metal leg of the stork to the tree with staples or in any other way.
- Pipe, chimney. Decorative storks will look great above the chimney, but remember that if it is working, then the smoke should go out unhindered. This means that it is necessary either to raise it above the chimney at least a meter using metal rods, or place it nearby. In any of these cases, when the chimney is running, protection from sparks will be required, therefore it is advisable to fence off
A well-groomed and ennobled cottage contributes to the creation of an atmosphere of peace and tranquility. A do-it-yourself stork for the garden is a great addition to flower beds, flower beds and lawns. This bird is a symbol of happiness, prosperity and prosperity. Garden sculpture of a stork looks good anywhere. You can install it on the ground, roof, pole or tree. To give the product realism, a technique such as building an artificial nest is used.
Figurines of storks for giving bring happiness and benefits, they are also a good decoration for lawns and flower beds.
Sculpture from plastic bottles and plywood
To work, you need several plastic bottles of black and white color. The basis of the structure will be a sheet of waterproof plywood.
To work, you will need the following tools and devices:
- jigsaw;
- scissors;
- screwdriver or screwdriver;
- pliers;
- a hammer;
- steel staples;
- self-tapping screws;
- glue gun;
- red nail polish;
- thick wire.
The stork can be made from plywood and plastic white milk bottles that are cut into fringes for plumage.
After the tools and materials are prepared, work can begin.
It is carried out in the following sequence:
- A paper template of the body and wings of the bird is made. The size of the statue is chosen based on the size of the site and the tastes of its owners.
- The plywood is marked. Cutting out blanks.
- The edges of the blanks are polished. Plywood is primed.
- The wings are attached to the body of the stork with the help of self-tapping screws. As a rule, wings are made in the folded position.
- The legs are being made. For this, a steel bar with a diameter of 6-10 mm is suitable. With the help of staples, steel parts are nailed to plywood. The lower edge of the rod can be sharpened for the convenience of fixing the product in the ground or nest.
- The bottom of white milk bottles is cut off. What is left is cut into 2 parts vertically. Stripes are cut with scissors. They will imitate feathers.
- Similarly, a plastic fringe is prepared from black bottles.
- The cut fragments are attached to the plywood base. This is done from the tail. Black stripes are attached first. They get off the lower part of the body, tail and wings.
- The rest of the bird is trimmed with white plastic stripes.
- The beak is covered with red nail polish.
- The eyes are drawn with black paint. You can use large buttons or eyes from one of the old toys.
The stork figure is ready. It can be easily attached to any surface. With the onset of inclement weather, it is better to remove the product and store it in a warm room until spring.
Back to index
Making a stork from foam
Typically, after external insulation there are quite a lot of foam plastic scraps left on the walls. They do not need to be disposed of. From this material you can make a lot of interesting and beautiful crafts. Polyfoam is light and easy to handle. You can make a stork out of foam plastic quickly, without the use of complex tools.
To work, you will need the following materials and tools:
- glue;
- sharp knife;
- steel bar;
- saw on wood;
- pliers;
- sandpaper;
- black paint;
- paint brush.
Making a sculpture of a stork for the garden is carried out in the following sequence:
- Wire blanks are made to imitate the legs of a bird. Their lower ends are sharpened. The upper ends of the rod are bent at a right angle for fixing in foam.
- The contours of the body parts of the bird are applied to the foam. The largest fragment should be the central part of the torso. The remaining fragments will be needed to give the figure volume, create wings, neck and head.
- The pieces are cut out. This is best done with a saw.
- Steel bars are fixed to the central part of the body. In order for subsequent fragments to lie tightly on the base, grooves for the rod are made in it. To avoid lateral vibrations, the rod is fixed to the base with additional brackets.
- Styrofoam strips are glued to the central part of the body, giving volume. Wings are glued on top of them.
- The neck and head of the sculpture are mounted on the pin.
- With the help of a knife and sandpaper, the stork figure is given its final shape. Additional finishing is not needed, since a relief imitation of feathers can be created on the foam.
- The tail and wings of the bird are painted with black paint. The beak can be wrapped with red tape or painted.
The final stage of needlework are the eyes. They are made from steel bearings or glass balls.
Back to index
Using mounting foam
An unused foam can can be successfully used to make a three-dimensional stork figure. With the help of foam, you can quickly make a three-dimensional blank, from which you can cut out the desired shape.
For work you will need:
- plastic bottle with a capacity of 5 l;
- scotch;
- Styrofoam;
- steel bar;
- primer;
- paint brush;
- acrylic paints;
- sharp knife;
- rasp.
There is a similar set in the closet of every house. Additional costs will not be required.
A garden decoration is made in the form of a sculpture of a stork in the following sequence:
- The steel frame is assembled. For strength, it can be fixed by welding.
- A plastic bottle is put on the frame.
- Styrofoam strips are taped to the neck wire. You can pre-grind them in shape and glue them.
- On the pins intended for the legs, the femoral parts, machined from foam, are placed.
- The finished frame is wetted with water. Foam is applied. It covers the entire surface of the workpiece, except for the wire imitating legs.
- After the foam hardens, all excess is cut off. Relief is given with a knife and a rasp. After finishing, the sculpture is cleaned of sawdust and dust.
- The dried product is covered with a primer. Next, the bird needs to be painted acrylic paints. Lacquer is applied over the paint.
To give the sculpture realism, you can use natural black and white feathers that are inserted into the tips of the wings and tail.
For reliability, they need to be planted on polyurethane glue.
The finished figure can be installed in the garden for a long time. The stork, decorated with acrylic paints, perfectly tolerates exposure to ultraviolet, cold and moisture.