The rather popular Protherm brand has long taken a firm position as a reliable manufacturer of heating equipment in Russia. In the entire model range of boilers powered by electricity, one series is presented - Proterm Skat. Protherm electric boilers are produced in 8 modifications with power from 6 to 28 kW with the possibility of smooth power control. Designed for use in closed systems heating with forced circulation of the coolant. Boilers are installed on the wall, and all connections are made at the bottom of the boiler. The efficiency is 99.5%, which is a very high figure, even among electric boilers. The entire series of skat boilers is single-circuit, and the implementation of hot water supply is carried out by installing a boiler indirect heating.

Most of these disadvantages and advantages are inherent in most boilers powered by electricity.

Advantages of Protherm Skat boilers

• High efficiency
• Easy to install
• Unpretentious in service
• eco friendly
• Doesn't require a lot of space
• Silent operation

Disadvantages of Skat series boilers

• The high cost of electricity
• Dependence on power outages

Sometimes electric boilers are credited with shortcomings that have not been relevant for a long time or were obviously wrong, consider some of them:

Boiler power is not enough to heat a house over 300 m2

This statement is incorrect, due to the fact that Skat boilers can be connected to a cascade to increase the heated area, with a shortage of 28 kW.

Frequent replacement of heating element

Due to the fact that the heat carrier is heated using a heating element, many people believe that such a heating element will not last much, but you need to take into account the quality of the heating element itself and do not forget that it is not water that circulates in the system, but the coolant.

Installation of Proterm Skat boilers in a cascade

If a 28 kW boiler is not enough to heat the house, it is possible to install Skates in a cascade to increase the coverage of the heating area.
When two boilers are connected in a cascade, the second boiler is controlled by a room thermostat, which is connected to the first boiler.
This scheme will look like this:

The contacts of the room thermostat are connected to terminals 1 and 2 located on the K8 connector of the main boiler, and the main boiler terminals 9 and 10 are connected to terminals 1 and 2 of the slave boiler.

In cascade mode, only the Proterm Skat 28 kW boiler and Proterm Skat 24 kW boiler are capable of operating.

Boiler device Skat

Skat boiler design

Features of Proterm Skat boilers

Stepped power setting

Depending on the model of the boiler, the number of power steps varies. The widest control range is available for skat boilers operating from a single-phase network and having a power of 6 and 9 kW.

Warranty

The warranty period for these boilers is 2 years.

A heating element

Depending on the power of the boiler, a different number of heating elements are installed in them; in the R13 modifications, heating elements were installed in accordance with the following table:

Work from the network 220V and 380V

Boilers with a power of 6 kW and 9 kW are capable of operating from a 220V and 380V network, boilers of higher power can only be connected to a three-phase 380 volt network.

Accessories for boilers Proterm Skat

When buying a boiler, in addition to it, the manufacturer offers various accessories to expand the functionality.

Temperature controllers

For Skat boilers, Proterm suggests using three types of room regulators:
Exabasic (article 6195) , Exacontrol (article 0020159367) and Exacontrol 7 (article 0020170571) .

The simplest Exabasic model has only a rotary switch for setting the temperature, Exacontrol is already equipped with a display and has a mechanical control. Modification number 7 - has the function of weekly programming.

Scheme of connecting the thermostat to the Protherm Skat boiler

Temperature sensors

To adjust the operation of the boiler, relative to the temperature outside the window, you should purchase a sensor outdoor temperature(article 0020040797).

Outside temperature sensor for boilers Protherm SKAT

In the retail network, its cost varies around 2000 rubles (38 euros).

Installation of the Proterm Skat boiler with a boiler

If you want to secure your home also hot water, then you need to purchase an indirect heating boiler. In order for the boiler to start working in conjunction with the boiler, you need to purchase a Fugas three-way valve kit (article 0020015570) for. The finished kit will cost 116 euros.

Set for connecting the three-way fugas valve to the Proterm Skat boiler Scheme of connecting an electric boiler Proterm Skat to an indirect heating boiler

Boiler errors Proterm Skat

Error F00

In electric boilers Proterm skat, error f00 occurs when the NTC sensor is disconnected at the heating outlet.

Error F22 - dry start

On the proterm boiler, the f22 error occurs due to a lack of water in the heating system.
To eliminate the error, it is necessary to add water to the heating system and turn on the boiler again.

Error F55

The appearance of this error f55 on the display occurs due to insufficient water.
It is necessary to disconnect the boiler from the mains and contact a specialist in boilers Proterm.
The error occurs when the relay or contactor is stuck, which are located on the board at the connection point of the heating elements.

Instructions, certificates and passport for the scat boiler

Hello everybody!
At the final stage of readiness, a house in Karelia, the material is glued laminated timber (205 width). First full, 2 attic floors. First floor - room (15 m2) + living room combined with dining room and kitchen (45 m2), bathroom and boiler room. Second floor 4 rooms of 15 m2, and a bathroom.

Heating - water floors (the builders and the specialist who installed my system said that this is enough), on the second floor, additional electric convectors.

No gas, only electricity. Accordingly, the electric boiler + boiler scheme was chosen (as far as I understand indirect heating). Electricity 3 phase 380V, 15 kilowatts.

I chose a Protherm Skat boiler for 14 kW, but I won’t pick up a boiler for it right away. What kind of boiler is needed for a family of 6 (residents)? Proterm has boilers for 200 liters, but the instructions for it say that the minimum suitable boiler for it should be 15 kW, i.e., do you need to take a smaller boiler? Is it enough for 6 people? Or maybe even take a separate boiler?

The SKAT boiler can be combined with
indirect heating boilers Protherm
type B60Z, B100MS, B100Z, B200S,
B200Z and B120S. Control system
the boiler regulates the heating of the boiler with
using the NTC sensor of the boiler. Sensor
should be connected to connector K8,
located on the control board
boiler or thermostat
boiler to be connected

to connector K9 (see electrical
boiler diagram, pos. 2). In order to ensure

Rice. eight

Wiring diagram for connecting peripheral devices to the boiler

1 power connection
2 boiler
3 room regulator
4 terminals for connection in cascade

(only for 24 and 28 kW series boilers)

Connecting an external DHW storage tank

proper functioning
boiler and boiler for their mutual
connections use connecting
kits recommended by the company
PROTHERM. Three-way terminals
valves are connected to the connector
K2 located on the control board.
Choosing storage tank or
connection kit, necessary
consult with the designer or
authorized service center
PROTHERM company.

5 terminals for connecting NTC sensor

indirect heating boiler

6 unload relays
7 outdoor temperature sensor terminals
8 room thermostat terminals

K9 thermostat connector

Electric boiler Proterm Skat

The rather popular Protherm brand has long taken a firm position as a reliable manufacturer of heating equipment in Russia. In the entire model range of boilers powered by electricity, one series is presented - Proterm Skat. Protherm electric boilers are produced in 8 modifications with power from 6 to 28 kW with the possibility of smooth power control. Designed for operation in closed heating systems with forced circulation of the coolant. Boilers are installed on the wall, and all connections are made at the bottom of the boiler. The efficiency is 99.5%, which is a very high figure, even among electric boilers. The entire series of skat boilers is single-circuit, and the implementation of hot water supply is carried out by installing an indirect heating boiler.

Advantages and disadvantages of Proterm Skat boilers

Most of these disadvantages and advantages are inherent in most boilers powered by electricity.

Advantages of Protherm Skat boilers

• High efficiency
• Easy to install
• Unpretentious in service
• eco friendly
• Doesn't require a lot of space
• Silent operation

Disadvantages of Skat series boilers

• The high cost of electricity
• Dependence on power outages

Sometimes electric boilers are credited with shortcomings that have not been relevant for a long time or were obviously wrong, consider some of them:

Boiler power is not enough to heat a house over 300 m2

This statement is incorrect, due to the fact that Skat boilers can be connected to a cascade to increase the heated area, with a shortage of 28 kW.

Frequent replacement of heating element

Due to the fact that the heat carrier is heated using a heating element, many people believe that such a heating element will not last much, but you need to take into account the quality of the heating element itself and do not forget that it is not water that circulates in the system, but the coolant.

Installation of Proterm Skat boilers in a cascade

If a 28 kW boiler is not enough to heat the house, it is possible to install Skates in a cascade to increase the coverage of the heating area.
When two boilers are connected in a cascade, the second boiler is controlled by a room thermostat, which is connected to the first boiler.
This diagram will look like this:

Cascade connection of boilers Proterm Skat

The contacts of the room thermostat are connected to terminals 1 and 2 located on the K8 connector of the main boiler, and the main boiler terminals 9 and 10 are connected to terminals 1 and 2 of the slave boiler.

In cascade mode, only the Proterm Skat 28 kW boiler and Proterm Skat 24 kW boiler are capable of operating.

Boiler device Skat

Skat boiler design

Features of Proterm Skat boilers

Stepped power setting

Depending on the model of the boiler, the number of power steps varies. The widest control range is available for skat boilers operating from a single-phase network and having a power of 6 and 9 kW.

Boiler power steps Protherm Skat

Warranty

The warranty period for these boilers is 2 years.

A heating element

Depending on the power of the boiler, a different number of heating elements are installed in them; in the R13 modifications, heating elements were installed in accordance with the following table:

The number of heating elements in boilers Proterm Skat

Work from the network 220V and 380V

Boilers with a power of 6 kW and 9 kW are capable of operating from a 220V and 380V network, boilers of higher power can only be connected to a three-phase 380 volt network.

Accessories for boilers Proterm Skat

When buying a boiler, in addition to it, the manufacturer offers various accessories to expand the functionality.

Temperature controllers

For Skat boilers, Proterm suggests using three types of room regulators:
Exabasic (article 6195) , Exacontrol (article 0020159367) and Exacontrol 7 (article 0020170571) .

Room thermostats for boilers Protherm Skat

The simplest Exabasic model has only a rotary switch for setting the temperature, Exacontrol is already equipped with a display and has a mechanical control. Modification number 7 - has the function of weekly programming.

Scheme of connecting the thermostat to the Protherm Skat boiler

Temperature sensors

To adjust the operation of the boiler, relative to the temperature outside the window, you should purchase an outdoor temperature sensor (article 0020040797).

Outside temperature sensor for boilers Protherm SKAT

In the retail network, its cost varies around 2000 rubles (38 euros).

Installation of the Proterm Skat boiler with a boiler

If you want to provide your home with hot water, then you need to purchase an indirect heating boiler. In order for the boiler to start working in conjunction with the boiler, you need to purchase a Fugas three-way valve kit (article 0020015570) for single-circuit boilers. The finished kit will cost 116 euros.

Connection kit for the three-way fugas valve to the Proterm Skat boilerScheme for connecting the Proterm Skat electric boiler to an indirect heating boiler

Boiler errors Proterm Skat

Error F00

In electric boilers Proterm skat, error f00 occurs when the NTC sensor is disconnected at the heating outlet.

Error F22 - dry start

On the proterm boiler, the f22 error occurs due to a lack of water in the heating system.
To eliminate the error, it is necessary to add water to the heating system and turn on the boiler again.

Error F55

The appearance of this error f55 on the display occurs due to insufficient water.
It is necessary to disconnect the boiler from the mains and contact a specialist in boilers Proterm.
The error occurs when the relay or contactor is stuck, which are located on the board at the connection point of the heating elements.

Instructions, certificates and passport for the scat boiler

» Installation instructions for the Proterm Skat boiler

» Passport for the Proterm Skat boiler» Certificate for the Proterm Skat boiler» Certificate for the Proterm Skat boiler Rostekhnadzor

Single-circuit boiler

By purchasing any heating unit, along with it you receive instructions - Proterm Skat 9 kW is no exception. The model range includes 8 units that differ from each other in terms of power - 6, 9, 12, 14, 18, 21, 24, 28 kW.

Note! An electric boiler can be used not only for heating. When purchasing an additional heating boiler, it can be integrated into the hot water supply network.

Advantages of heating boilers Proterm Skat

Electric boilers PROTHERM Skat have become a good alternative gas equipment rapidly gaining popularity. They are ideal for operation where gasification has not yet taken place. Of course, this choice is well suited for suburban country houses with seasonal or occasional residence.

Among the main distinctive features Skat boilers should note the following:

• Ease of installation. The delivery set of the Proterm Skat boiler includes detailed instructions, which not only describes the settings of the equipment, but also gives recommendations for the installation and commissioning of the unit.
• Good efficiency. According to this indicator, electric boilers are not inferior to other popular heating equipment, including gas.
• Ease of setup and operation, as well as minimal maintenance.
• Precise temperature control.
• Environmental friendliness.
• No need to connect to the gas network and the need for a chimney.

During its existence on the market, Proterm Skat boilers have earned a reputation as the safest and most economical heating electrical equipment.

Boiler installation

Device diagram

The delivery set of PROTHERM Skat electric boilers includes all the necessary fasteners and a detailed manual that describes the connection work step by step. Modifications that differ in power have the same principle of installation, configuration and operation, therefore, as an example, let's take an electric boiler with a capacity of 9 kW.

Before installing the unit, it is necessary to coordinate the work with the electrical distribution services.

Modifications of the unit 6 and 9 kW are connected to a conventional 220 V power supply. More powerful options - 12, 14, 18, 21, 24, 28 kW - to a 380 V network. Mounting is carried out on the wall using a special mounting plate. The unit has no restrictions on the choice of installation location. The only requirement is the possibility of free access for maintenance, service, repair, adjustment, etc.

Wiring diagram

The unit is connected to the pipe system using nozzles. The connection itself is carried out in such a way that in case of malfunctions in the operation of the device, the coolant can be drained only from it, without affecting the system as a whole. Filling the boiler with coolant and draining it from the unit are carried out using additional valves. To prevent freezing of water during the cold season in houses with seasonal living, it is recommended to completely empty the system before lowering the air temperature.

The boiler is connected to the electrical network through a separate power line. The mains wires are connected to the terminals located in the lower corner of the unit body. All screws on the connectors must be carefully tightened. 6 and 9 kilowatt modifications can be connected to a single-phase network, the rest - only to three-phase ones.

Conclusion

Installation and connection of Proterm Skat electric boilers is quite simple. However, this requires special skills. It is better if the installation is carried out by specialists. In any case, it is better to entrust the development of a unit connection project to professionals. This will avoid failures and breakdowns during further operation.

On the world market heating equipment Protherm products are popular due to their reliability and high quality. Its equipment is supplied to many countries for corporate and private clients. The consumer can easily pick up heating equipment, because the lineup reaches almost 100 positions, including:

1. electric, gas, diesel boilers various modifications;
2. storage and instantaneous water heaters;
3. various sensors and automation for heating units.

In the line of heating equipment of the PROTHERM brand, the line of electric boilers for heating is represented by the Skat series. The company has established a wide network service centers, which ensure the uninterrupted operation of the heating equipment of the company adapted to the conditions of Russia. Therefore, buying an electric boiler Proterm Skat is beneficial due to the presence of a service network. The official website of the company presents a catalog of Protherm products for 2016. It contains the most up-to-date information about the heating units produced by the company.

In the company's catalog for 2016, the wall-mounted electric boiler Protherm Skat is represented by 8 models with capacities from 6 kW to 28 kW. Equipment with the letter "K" is connected to a 220/380 V network. All models of this line of electric boilers are double-circuit. The company also produces a line of models of single-circuit boilers in their name there is an abbreviation - "KR 13". Single-circuit boilers are produced in the same power range as double-circuit ones. The dimensions and weight of all models are the same and their main difference is the power, which depends on the set of installed heating elements and the supply voltage (220/380 V).

The catalog provides the main parameters for an electric boiler heating Protherm base model:

Advantages of Protherm electric boilers

Unlike gas, solid fuel and diesel heating boilers, they do not emit any harmful products during their operation, they do not need a chimney and various additional devices.

According to its properties, the Protherm electric boiler is absolutely harmless to environment and does not require constant monitoring during operation.

So, the Protherm Skat 9k electric boiler, however, like the rest of the company's electric boiler line, is fully automated; an LCD display is installed on the front surface of the case, which reflects the set readings. The delivery set includes detailed instructions for the Proterm Skat 9 electric boiler, which shows all the steps to achieve the smooth operation of the unit.

It is enough for the owner to set the desired temperature, and in the future it will be maintained by automation, with high precision up to one degree. After reaching comfortable temperature the thermostat will send a signal to the boiler control unit, which will turn off the power supply. Electric boilers safe, because automation monitors not only the temperature of the coolant, but also its pressure. To prevent sudden voltage surges, the boiler reaches the maximum mode in steps. A double-circuit electric boiler Skat of any model, except for heating, heats water for a hot water supply system (DHW).

Electrical heating boilers extremely compact and fit perfectly into any interior. Wall-mounted electric boilers Proterm Skat can heat areas from 60 to 280 m2 and are perfect for heating apartments, country houses, cottages and offices. Especially good feedback for an electric boiler Proterm Skat 6 kW, which can provide a small office with heat and hot water. There is an example when the owner installed a remote tank, the water in which is heated at night, because the region has a night tariff, and during the day it gives off heat to the room.

Installation and connection of electric boilers

In the instructions for installation and installation of the unit, included in the delivery of Protherm electric boilers, there is a warning that in case of mechanical damage to the body, violations of the integrity of the units and blocks of the boiler, the warranty becomes invalid. Therefore, with self-assembly, you need to work carefully and clearly follow the recommendations. In order for the Proterm wall-mounted double-circuit electric boiler to function correctly, it must be connected in accordance with the requirements of the instructions.

Connection to the electrical network of the boiler Proterm 6 kW

The boiler with a rated power of 6 kW is available in two options for connecting heating elements for 220 V and for 380 V. Boilers and heating elements are no different and the 380 V boiler option can be easily converted into a 220 V option. To do this, it is enough to change the switching scheme. If the boiler is connected to a three-phase network, then 2 kW heating elements in each phase consume a current of about 10 A, since the line voltage is 220 V. Therefore, 1.5 square wiring and a 10 A three-phase machine will ensure normal operation.

With a single-phase network, everything is somewhat more complicated. There are 6 heating elements installed in the boiler and with a maximum power of 6 kW, the current consumption will be slightly more than 27 A, therefore, you will already need a wire with a cross section of at least 6 squares and a 30 A circuit breaker. All of the above applies to any electric heating boiler for the home, of any power , only the values ​​​​of the consumed current and the desired cross-section of the wires will depend on the power.

According to the tables for section selection copper wire a current of 1 A requires a cross section of 0.17 mm2. The current in the circuit is determined by the well-known formula - I \u003d P / U, in which:

The first thing to pay special attention to is correct selection section of the electric power cable. Indeed, for example, an electric boiler Proterm Skat 24 with a rated power of 24 kW, when connected to a three-phase network, will consume a current of about 30 A for each phase. It is undesirable to connect such a powerful boiler to a single-phase network, because in this case the current at maximum power will increase to 100 A. You need to connect an electric boiler only through an RCD.

As for the installation site, the requirements for installing electric boilers are not as stringent as for gas or solid fuel units. And the price of an electric boiler for heating a house is much lower than the prices of other types of boilers.

You can install an electric boiler anywhere, but this place should provide easy access for adjusting the unit or quickly shutting it down if necessary.

If several electric boilers are provided in the circuit diagram, then they are connected in parallel. According to electrical safety regulations, electrical heater must be grounded.

How to choose an electric boiler for home heating

All are compact, easy to operate and safe. They do not need chimneys and special installation rooms, and the efficiency is close to 100%. In these properties, they are superior to other types of boilers. For heating a particular room, an electric boiler is selected primarily by power. It is believed that one kilowatt is sufficient to heat 10 m2. Therefore, the Proterm Skat 12 electric boiler with a rated power of 12 kW can provide room heat with total area 120 m2.

The high quality and reliability are confirmed by the reviews found on the network for the Proterm Skat 12 electric boiler, in which they write that the boiler is silent, simple and easy to adjust and does not require constant attention (“installed, turned on and forgotten”).

Popular Protherm electric boilers

For connection as a backup to an existing heating system or for heating small house with an area of ​​​​up to 90 m2, the wall-mounted electric boiler Protherm Skat 9 kr 13 with the possibility of using a 220/380 V network is in greatest demand. electronic control and with built-in circulation pump and . Its main characteristics are fully consistent with the base model.

If there is a need for organizing hot water supply, the manufacturer has provided the possibility of connecting an external tank. When sold, the connection pipes are closed with plugs. The difference in price between single-circuit and double-circuit boilers small. For example, the price of a Proterm Skat 9 kW wall-mounted double-circuit boiler is comparable to the price of a boiler of similar power, but single-circuit. In different stores selling heating equipment, the price of an electric boiler Proterm Skat 9 ranges from 490 to 560 USD.

By their own technical specifications, according to the requirements for installation, adjustment and design, electric boilers are much preferable to gas and. For their installation, a separate room is not required, and the electric boiler itself can be installed anywhere in the heating circuit, the main thing is that it has free access. Electronics developed by Protherm independently monitors the level of air temperature in the room and creates comfort and coziness in the home. The only obstacle that limits the use of electric boilers is the high price of electricity, which tends to increase.

Installation of Protherm Skat electric boilers, Proterm Skat installation

Installation of electric boilers Protherm Skat

Installation of electric boilers Proterm SKAT in Moscow

The wall-mounted 1-circuit electric boiler Proterm Skat is designed for the needs of heat supply in private houses, apartments and offices. Heat generation installations differ:

• - electric boilers with stylish design;
• - no need to connect to the gas flue and gas pipeline;
• - the ability to connect a 3-phase power supply;
• - ease of maintenance and operation;
• - high efficiency throughout the entire operational period;
• - environmental friendliness;
• - noiselessness;
• - possibility of fast regulation.

A feature of devices for generating thermal energy Proterm Skat is high functionality, which ensures that the thermal installation is turned off when the power supply is interrupted and the operation is resumed when the power is supplied, while maintaining all presets. The settings are displayed on the ergonomic display that the boiler is equipped with.

Protherm Skat heat exchangers have great capabilities, the initial setting of which occurs during commissioning, and can later be changed by the user if necessary:

• - adjustment of the temperature of the heat carrier is carried out on the panel of the thermal installation;
• - adjustment of the operation of heat generation units is carried out under individual system heating;
• - installation is possible remote control power supply from a tariff meter;
• - it is possible to install sensors room thermostat and an outdoor t sensor to control an automatic electric boiler.

Stock

1. When buying equipment and ordering installation, you get discount -10% to work! 2. When purchasing equipment, ordering installation, start-up and concluding a service contract for maintenance, you receive an additional emergency call for free(24 hours)!

List of boiler installation works and estimated prices

№	Name of works	Price, rub)
Wall mounted boilers
1	Installation of a wall-mounted boiler with connection to an existing system*	7500
2	Installation and installation of a coarse filter for the heating system (with stopcocks)	3000
3	Installation and connection of hot water supply (single point)**	3800
4	Installation and connection of sewerage (one point)**	2800
5	Assembly assembly and connection of one manifold cabinet**	5600
6	Installation and connection of the heating system (one point)**	4300
7	Installation of the power supply of the boiler room **	4000
8	Mounting coaxial chimney with hole punch	3000
9	Installation of stainless steel flue pipes up to 160 mm in diameter chimney up to 2 running meters	2000
Gas water heaters
1	Mounting gas water heater	4000
2	Supervised installation of a gas water heater	3000
Floor standing boilers with atmospheric burner
1	Installation of a floor boiler up to 40 kW	11 500
2	Installation of a floor boiler up to 60 kW	14 800
3		20 000
4	Installation of floor standing boiler up to 150 kW**	negotiable
5	Setting the boiler safety group	2000
6	Installation and connection pump unit	4500
7	Installation and connection of a boiler up to 400 l	8500
8	Installation and installation expansion tank for DHW	3500
9	Installation of boiler safety group and recirculation pump	2500
10	Wall chasing 1 working day*	10 000
Floor boilers with air burner
1	Installation of a floor boiler up to 100 kW	25 000
Electric boilers
1	Installation of an electric boiler with connection to existing pipes and power supply	7500
Equipment dismantling
1	Simple dismantling of the boiler (polypropylene/metal-plastic piping)	5000
2	Difficult dismantling (steel strapping)	10 000

* The price for installing a wall-mounted boiler is given on the basis of its simple installation to existing pipelines, a chimney, without the need to replace or install a chimney, fittings and other equipment necessary for the operation of the boiler.

**Prices are given as a guideline, the exact cost of installing a boiler house is formed after an inspection of the facility, taking into account the individual wishes of the customer.

Our services

For long-term and efficient operation of the Proterm Skat electric device for generating thermal energy, it is necessary that the installation and installation be carried out by service technicians with special education, professional knowledge and practical experience.

Ajax Thermo offers complete list services for the selection of electric boilers for individual heating, installation and commissioning of Protherm Skat heat exchangers.

• - The company's specialists will connect the heating boiler to the alternating current network.
• - Adjust the t of the heat carrier of the electric boiler.
• - Set up the equipment for the individual heating system of the customer.
• - If necessary, install and connect an additional boiler for heating water.
• - Set up the ability to control the operation of an electric boiler from an outdoor t sensor or a room thermostat.
• - Connect a voltage stabilizer to ensure the safe operation of electrical equipment.
• - Adjust the protection function of the heating boiler against pressure drop in the system, against freezing or overheating of the boiler.

Our company has significant experience in the market of installation and installation of automatic heating systems and electric boilers of varying complexity. Attractive cost of services, high level of service, warranty and post-warranty service are additional benefits of cooperation with Ajax Thermo.

1. 1. mounting Baxi
   2. installation Baxi MAIN