coupe 

Boilers for heating electric water for the bathroom. Which water heater is better to choose for the bathroom. Corridor and hallway

To solve the problem of constant hot water supply in the bathroom, it is easiest to install an instantaneous electric water heater for the shower. It has significant advantages over a storage device, which we will discuss in detail in this article. And we will also pay attention to the minuses, the main one is the need for a special approach when providing electricity.

Also in this material we will give recommendations for choosing a suitable water heater, including the calculation of sufficient power. Denote the best manufacturers electrical models, we focus on installation and maintenance. Indeed, for uninterrupted operation, it is necessary not only to correctly calculate the parameters, but also to carry out the installation in a qualified manner.

The choice of a water heater for a shower between a flow-through and storage type of device is not always unambiguous. Each of them has its pros and cons, and the solution in most cases depends on the capacity of the power supply system.

The internal structure of the device

In bathrooms, non-pressure water heaters are installed for one collapsible point. They are designed for a single consumer, have 1-2 heating elements and rarely exceed 8 kW. A, sufficient for the operation of such devices, should be from 0.03 to 0.6 MPa.

The device is turned on when the flow sensor is triggered. The overheating sensor determines the water temperature and turns off the heating elements when it goes beyond the allowable range.

The indicator signals to the user about the operation of the heating elements. If it is turned on, and the water does not heat up, then this means a breakdown of the heating element - the most common problem with instantaneous water heaters.

The device of the Thermex instantaneous water heater does not differ from similar devices from other companies. However, when repairing, it is better to use original parts.

For all water heaters, the place for connecting the hose from the water supply is marked in blue, and for the shower head or faucet - in red

The placement of sensors for the flow of water and its overheating does not allow the heated jet to pass in the opposite direction. Therefore, for the safe operation of the device, it is necessary not to confuse the input connection points. cold water and output heated.

Also, for many devices, there is a restriction on maximum temperature incoming water. As a rule, it is 30-35 degrees. If this value is exceeded, the overheating sensor will definitely work and the water heater will turn off. Therefore, it is impossible to connect the device to a hot water pipe when, according to the consumer, insufficiently heated water flows there.

Advantages of flow models

The first advantage flow device is significantly smaller. Placing it in the shower room and self-installation does not cause problems, while finding a place for a massive tank storage water heater and it presents significant difficulties.

The second advantage is the significantly lower cost of a domestic instantaneous water heater designed for a single point of consumption. Depending on the configuration and brand, the price range of such devices is 1,700 - 8,000 rubles, while the price of a simple storage water heater with a tank capacity of 30 liters or more starts at 5,000 rubles.

Maintenance and repair of storage devices must be carried out more often, and it is more expensive. In addition, not every consumer can carry out their independent installation and connection, which incurs additional costs for paying for specialist services.

When using a storage water heater, the number of people must be taken into account when calculating the volume of the tank. However, in the event of the arrival of guests, it may not be enough. The flow analogue is devoid of such a disadvantage.

We have more criteria for comparing instantaneous and storage water heaters.

Nuances of connection and operation

For trouble-free operation of an instantaneous water heater, you will need to study the principle of its operation and know the main technical characteristics of the device. There are also nuances of connection and maintenance that will avoid problems during its operation.

How to connect the water heater correctly?

There are water heaters with bottom, top and side water supply. In bathrooms, as a rule, use the lower option. Decide on optimal way connection is necessary before purchasing the device, as it is forbidden to install it in a different position.

Connection to cold water occurs in two ways:

  • to the shower connector of the faucet-shower switch;
  • directly to the cold branch of the water supply.

The first way leaves the possibility to use the standard water faucet to obtain cold water bypassing the water heater.

In user-designed plumbing system stop valves cannot be used after instantaneous water heater. Otherwise, it will lead to its overheating, even if there is a shutdown function by a temperature sensor. This rule is directly indicated in the instructions for many devices.

A typical option for connecting a flow device to a cold water system. Shower switch and faucet are located before the water heater, and after it the flow is free

According to the requirements of electrical safety, regulated for hygienic premises GOST R 50571.7.701-2013, sockets for 220 volts must be installed in the third zone (further in plan than 60 cm from the shower, bath or sink tap) and must comply with the degree of protection IPX4 or higher.

At a distance of more than 3 meters from the water supply points, ordinary class sockets can be installed. IPX1.

Despite the fact that the instantaneous water heater is designed for wet rooms and has good tightness, when choosing an installation location, it is necessary to take into account the undesirability of direct jet hot water. This is how the case heats up, which will negatively affect the tightness of the connections and the performance of the control panel. In addition, the ingress of water reduces the strength of fixing the device to the wall.

Mounting to the wall is standard methods using screws. The weight of the device is from 1 to 3 kg, so no measures for reinforced installation are required. Some owners do without fixing the device, but this is not necessary, since there is a risk of the device falling and depressurizing during its operation, which is dangerous for people in the room.

Do you want to install a flowing water heater on your own? We recommend that you familiarize yourself with the installation.

If it is not possible to install a water heater outside the bath or shower, then it should be placed as high as possible. In this case, the amount of water falling on it will decrease.

In addition to wiping the surface of the water heater with soapy water, periodic maintenance consists in changing the filter installed on the cold water supply.

For this, the following actions are performed:

  • disconnect the device from the power supply;
  • close the tap on the water supply;
  • unscrew the hose;
  • remove and rinse the mesh filter;
  • assemble the device in reverse order.

For trouble-free operation, it is important to properly configure the equipment.

The water temperature must be set in the following order:

  1. Open the faucet and wait for the water to flow from the water heater.
  2. Turn on the water heater. After 10 seconds, the temperature will become constant.
  3. If the temperature is not suitable for taking a shower, then by adjusting the pressure and operating modes of the water heater, change it.

After each action to change the pressure of the water supply or the power of the heating elements, it is necessary to wait 10-15 seconds to establish constant temperature values.

We have provided detailed instructions for the operation and maintenance of the water heater.

Conclusions and useful video on the topic

Mounting to the wall, connecting the water supply and starting the water heater Electrolux Smartfix:

An example of incorrect use of a water heater. The device is not fixed, the faucet is installed after the hot water outlet:

The calculation of the required power of the instantaneous water heater, its fastening and connection to the water supply can be done independently. The greatest difficulty is the safe provision of the device with electricity. Choosing a well-known manufacturer will ensure that problems are quickly resolved if the device breaks down.

Do you want to ensure the year-round availability of warm water in the shower by installing a flow-through model of a water heater, but your friends convince you of the inefficiency of such a solution? Ask your questions under this article - real owners of instantaneous water heaters will share with you their experience of use and their own opinion on the advisability of installing it.

A problem with hot water every person is present at times, and therefore, in order not to rely on centralized water supply and constantly have hot water in the bathroom, you should think about installing a water heater. Which water heater to choose for the bathroom, we will tell you right now.

Today we decided to slightly change the format of the article and not just talk about the advantages of certain water heaters and consider instantaneous and storage water heaters for the bathroom, but immediately move on to readers' questions, which we will answer. So, questions and answers that will quickly guide you when choosing a water heater for the bathroom.

Which water heater to choose?

We suggest you consider only two types of water heaters - instantaneous and storage. We want to say right away that instantaneous water heaters are more suitable for a kitchen or bathroom for summer use, since you will not be able to get a standard strong pressure of hot water with their help. But, on the other hand, you can consistently get enough warm water, which can be rinsed, in which you can wash and so on. If you are more interested in a relaxing bath or a large number of hot water for other needs, we recommend you a storage water heater, but remember that there is one definite minus - storage water heaters heat water for a long time.

Which instantaneous water heater to choose?

If you opted for a instantaneous water heater, then we recommend that you purchase a device according to the following criteria:

  • Sufficient power for heating water;
  • Easy-to-install shape and size of the water heater;
  • Compulsory quality assurance of internal manufacturing materials, certified production;
  • Nice design of the water heater, because most often, it is in plain sight.

Which storage water heater to choose?

When choosing a storage water heater, we advise you to pay attention to the following:

  • Water heater power, water heating time, electricity costs;
  • The volume of the tank, the possibility of reheating water and maintaining the temperature;
  • Automatic control - on / off when a certain temperature is reached;
  • The quality of the internal equipment - the tank, the heating element, and so on;
  • Protective functions of the water heater - automatic shutdown, operation check valve, other;
  • Warranties and documentation for the water heater;
  • Appearance, shape, dimensions.

What brand of water heater is better to choose?

Many of us are interested in which water heater company is better to choose? This is the right and timely question, because we need quality and durability, practicality and ease of use, and therefore, we need to focus on brands that have earned consumer trust.

So which brand of water heater should you choose? We offer you the following options: Ariston, Atlantic, Delfa, Electrolux, Ferroli, Fregia, Garanterm, Combustion, Nord, Nova tech, Round, Termex, Thermo.

Naturally, this is only a small part of the bathroom and kitchen water heater manufacturers that you can choose from.

How to choose a water heater by type?

If we are thinking about which water heater to choose for an apartment, for using hot water in the bathroom and in the kitchen, then it is necessary to dwell not only on the external parameters and power of the devices, but also on their types. Of all the currently available, we decided to choose only those that can be placed at home.

Choosing a gas water heater

It is good if the house has the opportunity to connect a gas water heater, because in many houses this is not allowed. If the permit system passes, then you can always get hot water at an affordable price.

The installation of a gas heater takes place right next to the gas source, that is, if you need hot water in the bathroom, then it will come from the kitchen. Installation of a gas water heater is carried out only by specialists, in no case independently.

Choosing an electric water heater

An electric water heater is convenient in that it is installed in any convenient place where you can arrange the supply of water to the tank and its intake. The distance can always be adjusted by the length of the pipes. Naturally, maintenance of an electric water heater in the bathroom will be more expensive than maintenance of a gas one, since appliances with high power consume quite a serious amount of expensive electricity.

Installation of an electric water heater (flow or storage) can be done independently if you have already encountered the installation of such equipment and connection work.

Today we dealt with many issues and found out which company's water heater to choose, which water heater to determine for the home - electric or gas, storage or instantaneous. It remains only to talk about the installation and connection of water heaters, which we will do in one of our next articles.

How to choose a water heater for the bathroom (video)

When choosing a water heater for a bathroom by type, be sure to make sure that it can be connected at home.

Which is better to choose a water heater: we draw conclusions

We believe that for use in the bathroom, where you wash and rinse, take baths and do light laundry by hand, an electric storage water heater is most suitable. He can always give a certain amount of hot water, which is necessary for use. If the hot water in the tank is over, then it seems to us that waiting for it to heat up for a couple of hours will not be a particular problem. Of course, you may have a different opinion, and we do not forbid you to think subjectively and do not impose your own opinion, but simply give good advice.

2016-11-29 Evgeny Fomenko

To enjoy all year round hot water you need to install a water heater for the bathroom. Before choosing a particular model, you should understand their varieties. There are two main types of electric water heaters - instantaneous and storage.

Types and features of instantaneous water heaters

Flowing water heaters are of three types:


Pressure water heater AEG MTD 350

At the same time, all three types have a number of advantages:

  • Small sizes. Great for small bathrooms. A good choice for Khrushchev, small families and dormitories.
  • Fast heating. The flow heats up within 30 seconds after switching on.
  • Ease of installation. There are no special requirements for the wall on which the device will be located, it does not require massive fasteners.
  • Possibility of unlimited use warm water.
  • Low price. The simplest models are inexpensive, from 3500 rubles.

Disadvantages of flow heating devices:

  • High electricity consumption. fast speed heating is achieved by consuming 5-25 kWh. Some devices are specifically not equipped with standard plugs so that they cannot be connected to household outlets.
  • The temperature of the water depends on the pressure. To draw a large amount of hot water, you will not have to fully open the tap.
  • The ability to provide only one point of water intake.
  • No supply of warm water. Since they don't have storage tank, when there is a power outage, hot water automatically disappears.

For bathroom rooms fit stationary instantaneous electric water heater. Enough for showering, washing, washing hands and cleaning. It is also important to consider how many people will use it. If there are many users, it is better to choose more powerful models.

Features of storage water heaters


Boilers are a tank in which water accumulates with a heating element inside.

Storage water heaters have several advantages:

  • Less power consumption. Boilers heat water and then only keep it at the right level. This does not require the device to work around the clock. AT modern models you can even prioritize heating at night to consume electricity at a cheaper rate.
  • Depending on your needs, it may suit you. If you are used to taking a bath, then you just need to choose a water heater from 100 liters. A small-capacity boiler is suitable for using the sink and shower.
  • If there is a power outage, you still have hot water in stock.
  • You can set a comfortable temperature level in advance. At the same time, you can safely dilute the water from the boiler with tap water using a mixer.
  • Possibility to connect several taps. One device is enough to provide warm water to both the kitchen and the bathroom.

Cons of accumulative models:

  • Large dimensions. This is especially felt if you have a small bathroom.
  • More complex installation. The boiler itself weighs a lot, plus it should be taken into account that it will be filled with water.
  • Long heating. In order to heat every 10 liters of water, the boilers will take 30 minutes. If the device long time was turned off, you will have to wait at least an hour until the desired temperature.

When choosing a device, you should pay attention to three main parameters:

  1. The form. Today you can choose a convenient shape of the tank for your room. Flattened rectangular models look more convenient and beautiful. You can also choose the traditional vertical or horizontal layout. There is floor structures and which are attached to the wall.
  2. The material from which the tank is made. More durable models with a stainless tank. According to reviews, it can last about 10 years. Cheaper and less reliable enameled tanks.
  3. TENA design. Over time, scale accumulates on the heating element, which must be cleaned prophylactically. Models with a closed heating element last longer, in which the heating coil does not come into direct contact with water.

Best of all for a bathroom, either a stationary flowing water heater or a storage boiler of the required displacement is suitable.

Look at the video below general scheme installation of a storage water heater, as well as typical mistakes during installation and connection:

Repair of heating networks, interruptions in the supply of water - situations familiar to many. Of course, an hour - another can be tolerated. And if the repair is delayed? There is already a need for a water heater in the bathroom. Installing this device can completely solve all problems with interruptions in hot water. But the product market offers many water heating systems. This article will help you choose the right device.

There are several types of water heaters for the bathroom, which can be divided into three types:

  • geyser in the bathroom;
  • electric water heaters;
  • indirect heating devices.

Gas heaters are known to us under the name "columns". If they are installed - the owners appreciated their effectiveness. 16 liters of water can be heated in one minute. If it is possible to install it in the house, it is preferable to opt for this type of water heating. Owners of private houses are in a favorable situation.

But in order to install a gas boiler in the bathroom, you will need a chimney in the house and a lot of approvals and permits from regulatory organizations. Better choose electrical systems. They can be divided into:

  1. Storage water heaters that use a boiler.
  2. Systems of flow heating of water.

In storage systems, water is heated using a heating element. But in order to heat the boiler, heating elements of another type can be used. In water heaters flow type heat exchangers are used to heat water various designs. The choice of electric water heaters must be approached very carefully. Here you will need to take into account several conditions:

  • how many people live in the house;
  • how water is used;
  • wiring condition.

Speaking of wires. If the house is old, then most likely it will be necessary to replace the supply wiring with a grounding device.

Storage water heaters

It is the storage system (boiler) that has become widespread in Russian apartments. They can heat cold water and supply hot water either for the whole apartment or just for the bathroom.

The boiler is valued by the consumer for its low energy consumption and the presence of a certain supply of already heated water. Of the disadvantages that the boiler has, these are large dimensions to provide boiling water supplies for a small family of three. The water heater in the bathroom can be selected in a variety of designs and shapes. They may differ from each other in technical characteristics (for example, water consumption) and appearance. The spread in energy consumption is usually small - 1.4-2.5 kW. But the design and construction can vary significantly between different types.

To choose a boiler, you need to pay special attention to its durability. To a greater extent, it depends on the heating element - the heating element. According to their design, they are divided into two types:

  1. Boiler with dry heater (in this version, the heating element does not come into contact with water).
  2. Water heaters for a bathroom with a "wet" heating element, has direct contact with tap water. Such devices have a shorter service life due to constant contact with the city water supply, which contains various impurities.

Flow-through water heating systems

If you want to provide an apartment alternative source hot water, you can pay attention to flow systems. They are of three types:

  1. Stationary flow systems. They are mounted as a separate element, since they have a larger volume and require a separate place for installation. It could be under the bathtub or under the sink. The latter is equipped with a decorative pedestal, in which the entire water heating system is successfully “hidden”.
  2. Water heaters in the bathroom as a nozzle on the faucet. This universal device is put on the mixer tube in front of the rotary gooseneck. For the needs of washing or cleaning dishes, this design is ideal, but such a device cannot provide such a device to take a bath or wash in the shower.
  3. Faucet with electric water heating. A new type of instantaneous water heater heating device. It has its own water mixer. The water heats up in the same way as the nozzles but much faster (depending on how much the cold water supply is open). Such a system is quite realistic to apply in conditions where there is no hot water. For example, in cottages. It will not be possible to wash in the bathroom (the water will cool down), but it is quite possible to take a shower. Such a device is inexpensive, installed by the forces of its home "craftsman" and is characterized by low power consumption. Such a water heater in the bathroom has recently become very popular.

Preparing for installation

To begin with, before purchasing and installing a boiler, it is worth considering the connection system and designating the place where the entire structure will be located - in the bathroom itself or in the adjacent toilet.

If you decide to do the installation on your own, then it makes sense to prepare in advance necessary tools for work:

  • measuring tool,
  • hammer drill,
  • keys set,
  • flat or Phillips screwdriver (preferably a set),
  • pliers with cutters.

To connect the water supply and withdrawal system for the bathroom water heater, prepare in advance:

  • tow with fum tape,
  • plumbing fixtures (3 taps for storage devices and 2 taps for flow),
  • tees (quantity to be determined based on the type of connection),
  • metal-plastic pipes or special connecting hoses.

Most likely, you will need to either change the electric / wiring or conduct a new one. For this purpose you will need:

  • three-core wires,
  • fuse - automatic,
  • socket.

We connect the water heater

There are two options for connecting a water heater for a bathroom: a temporary scheme or a permanent one.

With a temporary option, there are no difficulties. For this:

  1. A tee cuts into a pipe with a cold water supply.
  2. A stopcock is installed.
  3. Connect the shower or faucet to the outlet of the heater.

In any case, when installing water heaters for a bathroom, it is necessary to carry out a minimum of construction and installation work:

  • The distance between the fasteners with which the boiler is equipped is measured with a tape measure and transferred to the wall.
  • A puncher drills holes in the wall for anchor bolts.
  • Anchor hooks are installed.
  • The whole boiler is hung on the wall.

Instantaneous water heater when installed permanently, it is most often done so that it works in tandem with the general water supply system in the dwelling. To do this, the work process goes like this:

  • tees must be inserted into existing pipes;
  • stop valves are installed;
  • connect the cold water supply pipe to the water heater above the bath (the connection point is marked in blue);
  • connect boiling water from the boiler with metal-plastic pipes with a tee with a mixer;
  • All connections are carefully checked. If there are leaks, they must be eliminated;
  • open the cold water supply to the system and connect the appliance to the socket.

Everything - the house is provided with an alternative source of hot water. If a boiler is installed, the work process is almost the same. The only thing is that before turning on the boiler, it is necessary to let it completely fill with water. To remove air from the tank, both supply and water intake taps must be open. If there are no leaks and the air is completely removed, the bathroom water heater is connected to the mains.

Now there is an idea about how and how you can connect alternative hot water systems and install water heaters in the bathroom. For a more complete understanding of the process of installing a water heating device, you can watch the video and read the installation manuals that are supplied with flow systems.

An electric water heater is a profitable and convenient alternative to central hot water supply, even to classic boilers. Such a device is capable of a short time warm a large amount of water, which will be enough for the bathroom and even the kitchen.

The problem of buying a boiler becomes especially acute for owners of private country houses, where there is no central water supply at all and the residents of apartments in summer time when scheduled outages and outages begin. It is in such cases that a water heater becomes a real necessity, capable of improving and facilitating everyday moments.

Flow boiler

Today, due to the high demand for water heaters, the plumbing market offers us a lot of options, different in cost, principle of operation and quality.

Variety of water heating devices

The first question that the consultant in the store will ask you is: “Which device do you want, electric or gas?”.

The market includes electrical and gas water heaters. The latest models, unfortunately, are not so popular, as they are not suitable for every home, and their installation is quite complicated. In installation and working principle, electric water heaters are more simple and convenient, so their market share is larger and more profitable.

Types of electric water heaters:

  • flowing;
  • flow-accumulative;
  • cumulative.

Each of the types has a number of advantages and disadvantages, so the choice of a particular model should be made according to technical specifications a certain product. The main difference between the devices is the dimensions. When choosing, keep in mind that flow-accumulative mechanisms were able to collect all the advantages of both options.

As practice shows, buyers are more interested in flow products, so we recommend that you take a closer look at such a profitable bathroom equipment.

Instantaneous water heater

Flow type water heater

The flow-type device looks quite compact and neat, which distinguishes it favorably from bulky boilers of 20-80 liters. The water heater does not have a storage tank, which makes it such a convenient size.

Water is heated through a flow mechanism, passing through a heat exchanger (heating element - heating element), reaching 40-600C and immediately entering the mixer, that is, for distributing water. This principle of operation ensures the ability of the device to heat an unlimited amount of water.

The heart of the instantaneous water heater can be called a high-power heating element, which is installed in the copper case of the device.

Unfortunately, such a device will work effectively only for one water intake point. Otherwise, the water flowing through the heating element will not have time to heat up to a comfortable temperature.

Advantages of the flow device:

  • compact dimensions, the device can be easily placed in a bathroom of any size;
  • the ability to get the maximum amount of hot water;
  • water heats up fairly quickly;
  • high service life;
  • does not require any maintenance;
  • easy installation and dismantling;
  • affordable prices for various models.

Thanks to a number of pluses, the variety of devices is growing, including their quality and additional features, so choosing the best model will be easy.

Disadvantages of instantaneous water heater:

  • a large amount of power consumption, that is, electricity;
  • connection to several points of water intake will reduce the efficiency of the device, that is, the level of water temperature;
  • most of the popular products have high power, which not every outlet can withstand;
  • a certain amount of water pressure is required.

If you need a constantly large volume of hot water, and the sockets cannot withstand the high power of an instantaneous electric water heater, you should consider storage devices. After all, not every apartment or house has the opportunity to use so much electricity.

Instantaneous water heater

If you decide to choose a flow mechanism, you can be offered a small type of water heater. They are forceful and non-pressure.

The pressure mechanism is quite simple, it has only an inlet and outlet for water. Installation is carried out in a "riser" and involves wiring to several points. The device turns on and off by itself, reacting to electricity water.

A non-pressure instantaneous water heater has its own nozzle and acts as a shower, that is, for one water intake point. Such a mechanism is more often purchased for a summer residence than for an apartment, because two mixers on the same wall are useless.

Looking ahead, I would like to note that you need to choose a device according to the power that the electrical network at home can withstand in order to choose the right flow heater of a certain performance.

Recommendations for choosing a flow type heating device

Choosing an instantaneous water heater is not so difficult, the only important characteristic is the power of the product. The performance of such devices ranges from 3 to 27 kW, and the catch is that not all wiring is able to cope with the high power of an electrical product.

Pay attention to the views flow heaters by power:

  • 220 V - single-phase models;
  • 380 V - three-phase models.

The first type - 220 V have some power limitations, the maximum allowable level is 12 kW. This setting indicates the maximum load level allowed for a home network.

Water heater doesn't look bulky

Electric three-phase models (380 V) have a correspondingly higher performance, the power of which reaches 30 kW. Such devices are connected to electrical network three phase type. Such conditions often exist in homes where an electric stove is installed. Remember, three-phase models are designed for quite high loads than they are in ordinary homes.

Experts note that for a calm and continuous shower under hot water, you need a water heater with a capacity of 8 to 10 kW. It will not be difficult for you to choose a product, because almost every model is accompanied by a table by which you can determine the power you need.

To wash dishes, hands or wash yourself, you will need a simpler water heater with a power of 4 to 6 kW. For taking a bath and providing hot water to the whole house, consider devices with a capacity of 15 to 25 kW.

Instantaneous electric water heaters are often equipped with built-in circuit breaker. Exceptions are a small part of the models.

The advantage is that the device turns on only when the tap is turned on, that is, it uses electricity only at the right time and not a minute more. Similarly, the system automatically turns off the heating device when the tap is closed.

Some models turn off on their own when the water overheats. However, more modern devices are already equipped with a thermostat that is able to maintain and control the set temperature.

Important details to know before buying a water heater:

One of the neglected moments is the issue of spare parts for the device and their cost. Sometimes it turns out that it is not possible to find at least one detail in our country for the simplest and most inexpensive model. Therefore, do not hesitate to check this nuance with the consultant.

Instantaneous water heater is quite practical and bargain that will only make you happy. For tenant apartment building device will become nice addition during periods of interruptions in the supply of hot water, and for the owner of a private house, a water heater will become a real salvation and indispensable equipment.

It will not be difficult to choose a device, the main thing is to determine the power you need and the matter will remain small.