coupe 

DIY clothes hanger: how to make, drawings, photos, floor and wall options. DIY clothes hanger: types, designs, drawings, manufacturing

Clothes hangers are a must-have in every home, as otherwise outerwear quite problematic. In addition, floor hangers are also useful in the bedroom, so as not to put clothes in the closet every evening and not to use chairs or armchairs. But in the store, beautiful furniture is quite expensive, so the best solution is a do-it-yourself outdoor clothes hanger. After all, from inexpensive materials, you can make original and beautiful hangers that will greatly decorate and make your interior comfortable.

You can make a clothes hanger from almost any material. But if you are going to do it yourself, the choice of material should be approached carefully.

Wood and plywood are best suited for work, these are the most practical and plastic materials that are easy to work with. If products from them are used in the house, then they are guaranteed not to be exposed to moisture and their service life will increase significantly.

Working with metal or plastic at home is quite difficult, so you should not choose these materials. It is worth considering the fact that sometimes there is a significant load on the hanger, so you need to use materials of appropriate strength so that the furniture does not break.

Examples of floor hangers using metal water pipes

When you buy wood or plywood, pay attention to their quality, because this is a guarantee that the hanger will look beautiful. In most cases, wooden products are only stained or varnished, so the texture remains visible on the surface.

Floor hanger in the form of a tree

Making a floor hanger is easy, and it does not require a lot of tools and materials. This hanger is made from two sheets of plywood, approximately 70x170 cm in size and 18 mm thick. For manufacturing, you only need glue, a jigsaw and sandpaper. The work itself will also not take much time and you will not find such hangers in any furniture store.

First you need to draw on one of the sheets of plywood the outline of the future product. This can be done simply by transferring the drawing to scale on plywood. The most important thing is that the legs are of sufficient width - about 60 centimeters. This is necessary for stability, since if you make them narrow, then the hanger will fall if you hang heavy winter clothes on it.

As you know, the theater begins with a hanger. The hallway also begins with coat racks. The hanger is an important interior element that can decorate and complement, as well as streamline the situation. It should look attractive and not take up much space. Today, the furniture industry produces wide range of all kinds of designs of various designs, but many are interested in how to make a clothes hanger with their own hands. It is these products that transform the atmosphere, make the premises unusual, original and with a "zest".

Making your own hanger is pretty easy. This will require imagination, as well as the desire to make something extraordinary, something that cannot be bought in a store. A homemade hanger will undoubtedly decorate any room and attract the admiring glances of guests. For its manufacture, you can use any materials at hand - empty bottles, beads, wire and all sorts of little things that are likely to be found at home. Gifts of nature, for example, a bizarrely shaped branch, as well as the remains of building materials after repair.

The design and shape of the future product depend on the wishes of the owner. You can look for inspiration on the Internet, see photos of the original hangers, or download a diagram of your favorite idea. In any case, you first need to decide on the type of hanger and the material for its manufacture.

What are hangers

There are two types of hangers that you can make yourself - wall and floor.

The wall hanger is the most simple solution. It usually consists of a horizontal bar to which hooks are attached in one or several rows; an upper shelf for hats or a special cross beam for "hangers" can be provided to it. The shape of the horizontal crossbar-base is usually rectangular or with rounded corners, but if desired, it can be made absolutely anyone. For example, in the form of a heart or a tree leaf.

Usually the wall hanger in the hallway is made of wood. The fact is that wood is an excellent natural material that can be easily processed at home: cut the desired shape from the canvas and cover it with any paint.

The floor hanger is a structure consisting of a vertical support on the base. Hooks for clothes are attached to the top of the support. It is important that the hanger is not only decorative, but also practical. Particular attention should be paid to the base. It must be very stable so that the structure can withstand the weight of the clothes and not fall. There are many design options for such hangers, but they differ not only in shape and size, but also in the material of manufacture.

Floor hangers

First, you need to decide on the material. Floor hangers are:

  • Metal.
  • Forged.
  • Wooden.
  • Plastic.

Metal products are very strong and durable, have a lot of weight, so they are considered the most stable. Metal hangers with elements of artistic forging are real works of art that will bring elegance to any hallway. However, not everyone is able to make this kind of product at home, because the work will require a complex tool and metalworking skills.

The easiest way to make floor hanger from the metal of the house - the conversion of an old floor lamp. It has a support and a lampshade, on which thick wire hooks can be attached. By the way, you can weave original patterns from it and use them as hooks for clothes. The base can also be decorated with decorative elements.

Wooden hanger - wonderful a budget option for the hallway. Wooden crafts do not go out of fashion. They fascinate with their natural beauty, they can be used for any style and direction in the interior.

To make a wooden hanger, you can use a sheet of plywood or board, but if you want to make something really unique, it is better to turn to the gifts of nature. So, a small dry tree can become the basis of a future hanger.

It should be cleaned of bark and knots, carefully treated with sandpaper and fixed to the base. In this case, it is better to provide support on three legs, it is considered the most stable. Then you need to decorate the top of the hanger. It can be made like a tree crown. As hooks, you can use a beautifully shaped branch, which must first be cleaned and sanded.

The final stage is the coating of the entire structure with varnish or paint. As a decoration, you can use balls or large beads, which are fixed with glue to the base of the hanger or on hooks.

A photo

Video

This video shows the process of making a wall hanger.

Here are some more ideas for inspiration.

Do-it-yourself clothes hanger is a fruitful idea. Theater begins with a hanger; house too. In the sense of spirit, atmosphere, "energy". The reason is simple: the first thing a guest looks for is where to hang outerwear. And if the hanger is clearly home-made, but comfortable, stable and durable, a positive reputation for the owner is provided.

The second argument for making a hanger with your own hands is prosaic: purchase prices are clearly disproportionate to production costs. A homemade clothes hanger will save you quite a visible amount in the budget. It is not difficult to make it, it will take a little material, and waste from repairs will also go into business. The tool in most cases can be dispensed with by hand.

These factors are especially felt if a floor hanger fits in the hallway. In addition, it can also serve as a dryer if its design is frame, see below, because. On such hangers, it is convenient to hang clothes on hangers, and the hanger itself moves away from the wall. If in the house it was possible to shield the dressing room, then the floor hanger best option. The cost of floor hangers is significantly higher than wall hangers, but there is nothing in the design that would not allow you to make a floor hanger yourself.

On the floor or on the wall?

It has already been said enough to make a choice, as long as there is enough floor space. However, let's finally compare how attractive a hanger is in a floor-type hallway:

  • Clothes hung on hangers dry faster, do not stretch; the collar and lining are not torn.
  • On a hanger approx. 1.5 m fits a seasonal set of clothes for the whole family, which will save on the closet and the area under it.
  • A shoe rack is naturally attached to the floor hanger, which simplifies the work of equipping the hallway and saves its area.
  • With correctly calculated dimensions of the hanger, neither the wall from the clothes nor the clothes against the wall are damaged.
  • The mobility of the hanger does not interfere with the rearrangement of furniture; after moving the hanger, it is not necessary to seal the mounting holes in the wall.

However, floor hangers are different, and not all of them are most suitable for living quarters. For example, for orders (from the old Russian “order” - office, office, office) floor lamp hangers, pos. 1-4 in the figure, it is inconvenient to hang clothes on hangers. Due to the small area of ​​​​support, they are rolled, especially loaded with wet winter clothes. To emphasize the functional inferiority of the product, such hangers are called hangers, and they often go on sale under this name.

Types of floor hangers

The best option is the same theatrical wardrobe frame hanger, pos. 5. In the version for residential premises, it is supplemented with shelves for hats, shoes and gloves / scarves; perhaps an additional tie rod, pos. 6. Disadvantage - the "legs" of the hanger get underfoot. In an attempt to get rid of it, hangers were invented - frames on a stand, pos. 7, but generally speaking, they fell even more than the orderly ones hung up. Another option is a hanger-frame without legs, leaning against the wall; we will remember this one. There are also folding frame hangers, but in everyday life they have almost no advantages.

If in the hallway with a place is generally tight, then a wall hanger is still more suitable. Simple wall hanger-sconce, pos. 1 in Fig., is as compact as possible, but not at all more convenient than the order, except that it does not fall from the next jacket to one side. Hanger-shelf, pos. 2 won't fall off if it's attached properly, and neither will hats/caps, but the wall and clothes rub against each other.

Types of wall hangers

Wall hanger panel, pos. 3, saves the wall, but not the clothes. Most of all, leather things wear out on such hangers. Tanners jokingly advise: how, they say, to distinguish a sheepskin coat from full grain leather from it from reverse? The first, with everyday use of a hanger-panel, loses its appearance in 2 winters, and the second - in half a winter. Considering the cost of products from genuine leather, that's no good. Therefore, hangers-panels on the wall for expensive things are often supplied with soft upholstery, pos. 4. As for wall hangers with an openwork shield, pos. 5, then in this case its meaning is only decorative: it does not protect either things or walls.

Floor hangers with chest and bench

There are also floor hangers-panels with a stand, for example. in the form of a cabinet, chest or chest, pos. 1 in fig. on right. This is not the best option: someone will once put something on the lid, and with the clothes removed from the hanger it will be whisked to the floor. Much more practical are floor hangers-panels with a bench, pos. 2. A flower under the seat is a matter of taste for the owners, if only he survives there, but the shoe box or chest for accessories to care for her in the banquette drawer is the place.

Clothes and keys

Regarding hangers-panels, the amateur master has an additional opportunity, namely: to provide such a sidewall at the farthest from front door edge. Perhaps not reaching the bottom, with a bevel or notch. The factory ones do not do this: the hanger should be designed for clothes sticking out from the side. One sidewall almost does not interfere with this, but it is not known how the hanger will stand with the buyer, and it is unprofitable to make right and left hangers.

What gives such an addition? Place for the housekeeper, invisible from the threshold. In the same place, on the side, there may be a dressing table or cabinet, but the main thing is that the master's keys will not catch the eye of a casual visitor, and they are in sight, according to criminologists, a serious factor in spontaneous illegal actions, without which, i.e. temptation, the visit of a not entirely trustworthy subject would have done well both for the owners and for him. You can, of course, make a key holder luxuriously designed and with a secret lock, but this is a lot of work and material costs. And so - a simple plank with hooks will do. Or just hooks screwed to the sidewall outside of the stowage section.

We will assume that a suitable design has already been selected, and let's take a look at how to make a hanger. Preferably wooden: the material is noble, natural, easy to process. Let's not forget other versions; more convenient in some cases. Let's start with floor hangers as the most functional.

floor standing

Lovers of crafting from the heart, having a milling tool for wood, can immediately take up the floor frame hanger with legs. Made from fine-grained wood hardwood(oak, beech, hornbeam, walnut, birch), it looks chic, and it will take only 360 mm of the floor in width.

A suit hanger works well as a prototype, you just need to make it higher and move the trouser bar up so that you can hang coat hangers on it. Instead of a tie rod and handles, a shelf can be installed, and a shoe shelf is mounted below. Drawings of such a hanger are shown in Fig.:

Drawings of a wooden floor hanger

With the indicated other dimensions, the structural and overall width (dimensions 430 and 460 respectively) without compromising strength and stability can be increased by 1-1.4 m, i.e. the hanger will be already a family width up to more than 1.8 m.

About hooks and trempels

Bags, umbrellas, scarves are also left on the hanger, and a bachelor can also have a skirt with women's underwear. Sometimes life is life. It is also more convenient to hang clothes on hooks for a short time. Therefore, in frame hangers, sometimes runner hooks are put on the main bar (the former trouser bar in Fig; height 1360). They or hangers, depending on the need, are shifted to the side in a crowd. But the hook-runners under the fingers turn out at the most inopportune moment. In a hanger of this design and similar ones, the problem is solved simply: the main bar is for hangers, and fixed hooks are attached to the top board.

Pipes and profiles

Original hangers are obtained from round or shaped metal or plastic pipes, see fig. However, despite all the design tricks, their organic vices do not go anywhere. The same as the orderly hung. But high labor intensity is added: in order to hide the connecting nodes, you have to strain both your arms and your head.

Pipe hangers

It is better to make a square base of a floor lamp hanger from pipes. With the same withdrawn floor area, the distance between the support points increases by 1.4 times. If the base is still heavier, then the hanger up to 1.7 m high turns into a full-fledged hanger. 60 mm sewer pipes are most suitable.

A short master class in pictures on making the base of a floor hanger from pipes is shown on the next. rice. Pipe sections - 150-300 mm each, depending on how much floor can be given to the hanger. In addition to them, you will need 3 straight tees, 4 right angles and 4 plugs. Connections - on glue for propylene or PVC, depending on the pipe material. Weighting - sand or small gravel.

Making the base of the hanger from pipes

One of the comments to original design begins with a question like this: “Why couldn’t you just solder?”. Judging by the fact that later in the same comment, 90 angles with a clear claim to professionalism are called bends (plumbing bends are oblique tees), another 2-3 and the same number of exclamation points suggest themselves to the question mark.

Nevertheless, the author of the product, albeit not knowing plumbing terminology, solved the problem in a completely engineering way. The hanger does not need tight joints, and a tube of glue will cost much cheaper than renting a soldering iron for propylene. Which, moreover, you need to learn how to use, spoiling a fraction of the material. For greater reliability, you can reinforce the connections with phosphated (black) self-tapping screws: on black, their heads are not visible, and the strength of the hanger will not decrease.

Note: the pommel in the original design is also made of pipes, but, frankly, its design is not the same ... It would be better to drill inclined holes in the rack and insert some strong pins into them using the same glue; wooden, metal.

simple frame

Scheme of a simple floor-wall pipe hanger

A frame hanger made of pipes can be without legs, just leaning against the wall with an inclination. However, its slope must be negative. There must be at least 350 mm between the wall and the clothes on the hangers. If the slope of the frame is positive (the upper crossbar is adjacent to the wall), then the lower one will "leave" from the plinth by 500-600 mm. In a small hallway, this is a serious inconvenience. In addition, they will either cling to the lower crossbar with their feet and it will beat the floor, or it will have to be fixed to the floor, and this is really bad: any violation of the flooring is fraught with complex and expensive emergency repairs. Have you seen furniture for sale that needs to be screwed to the floor? Is that a special purpose, for example. rack. And then, they also try to get by with fastenings to the walls and, in extreme cases, to the ceiling.

A diagram of a frame hanger with a negative slope of pipes is shown in fig. The materials are the same: line segments sewer pipes 60 mm, 90 angles and straight tees. Withdrawn usable floor area - zero. At the bottom there can be a shoe rack or a banquette. For fastening to the wall, in order not to drill a lot and do without expensive collet anchors, it is better to take a couple more tees: with their help, the holding beams - extensions are attached to the wall with a pair of self-tapping screws in dowels each.

wall

Simple hangers-panels do not require special analysis. How to make a wooden wall hanger, see for example. video.

Here we recall, firstly, the sconce hanger. Foldable, it can be very useful if a large company has gathered or the kids have returned from the yard at least squeeze it.

An example of such a structure is shown on the right in Fig. However, its creators were clearly guided by the principle: "Consumption is the basis of cash flow." The outer (folded) side of the flap bar is inactive and a locking mechanism is needed. And a separate hanger for every day.

Compact folding wall hanger

Meanwhile, folding wall hangers have been known since ancient egypt. In the local climate, outerwear was worn occasionally, in bad weather, but after wearing it, it was necessary to dry it. It made no sense to keep a separate hanger for this in the regions where it rains and cold once a year, not every year, so they came up with the one on the right in Fig.

When folded, the compact wall hanger of the Egyptians was fixed with a cypress stick. Now, of course, you can put a ball retainer or just a hook. The main thing is that the hook hooks should be in 3/4 of the circle, then nothing will fall off them even with the bar folded back. And without need, the whole hanger looks like just a stick on the wall; you can hang bags, umbrellas, keys on hooks.

More about hooks

The original wooden hanger can be made without metal at all, not counting the fasteners. Do not rush to throw away the New Year's pine or Christmas tree (only the blanks will need to be turned upside down):

Video: original do-it-yourself wooden hanger


Best of all, such a hanger will look in the country, in a bar or frame house. Depending on the interior design - and in a city apartment. She will go to the bathhouse perfectly: the touch of steamed skin on metal is unpleasant, and to some extent even traumatic.

Hangers in the nursery

Probably, all children scatter wearable things. There is no need to especially scold them for this: without knowing chaos within reasonable limits, you will not accustom yourself to order. Who is against - answer Friday's question to Robinson Crusoe: "Why doesn't God kill the devil?"

However, teaching children to handle things properly is necessary. Only a children's hanger, so as not to cause obvious psychological rejection, should look somewhat disordered. It is also highly desirable that the child associates it with a favorite game or hobby. Examples of wall hangers in the nursery of the "game / hobby" type are given in pos. 1 and 2 fig.

Baby hangers

A universal method of this kind is a tree hanger, pos. 3. In the contour of a tree, as in any fractal structure, order and chaos interact and complement each other, creating a harmonious whole. Do not forget to just make the tree stronger, for example. from plywood from 12 mm, and, as it should, with a step of no more than 250-300 mm, attach to the wall with self-tapping screws from 6 mm in propylene dowels. A tree, after all, to climb on it.

Floor hangers in the nursery are undesirable for the same reason: well, they will climb anyway and crash. Therefore, if you already want a floor hanger in the nursery, you need to make one that you can’t fit on, which can be seen in pos. 4 and 5.

About cutting plywood

In any case, parents face problems that small ones don’t care about yet: material consumption and labor intensity. It is no longer easy to draw a complex contour along a grid on a solid sheet of plywood, then it must be accurately cut out, which is even more difficult. And in the end it turns out that 60% or 80% of the material went to waste, no longer suitable for anything. It is necessary, on the contrary, to make a children's tree hanger from waste. Or cut a denser whole sheet.

Assembling parts of a plywood hanger-tree

The method for this has long been known: element-by-element cutting and assembly. If the tree is plywood, for the full strength of the finished product, each part is recruited from 2 layers, leaving resp. folds and grooves, see fig. Fragments of blanks are assembled on PVA glue, wood glue or Express (liquid nails). If the assembly is on PVA, the fragments must be additionally fastened with small nails with a snake in increments of 100-150 mm with an indent from the edges of 30-40 mm.

They assemble a tree hanger on the same adhesives, but now each connection must be fastened with self-tapping wood screws with an envelope. Then the gaps and fastener heads (they must be drowned during assembly) are rubbed with putty from sawdust of the same plywood on PVA. Such a tree, even without painting, only under varnish, will look solid.

Note: just in case, we recall - all wooden details before assembly, any wooden hanger must be sanded with fine sandpaper and treated with a water-polymer emulsion or PVA diluted with water three to five times. After impregnation, before further work, a technological break is made until the part is completely dry (1-3 days, depending on its size).

And one last thing about hooks

In the illustrations above, you most likely noticed curved wooden hooks and other hanger details. It is quite possible to make them at home. In production, dense, small-layer, defect-free wood or waterproof birch plywood (BS grade) is bent heated with steaming or dry, but these methods are too complicated for homework. Only bamboo is more or less simply steamed: the workpiece is boiled for half an hour or an hour in rapidly boiling water, after which it is bent by hand. In case of bending according to the template, the workpiece must be fastened to it quickly, before it has cooled down, with a wide cotton braid or a strip of natural tarpaulin.

Wood rasp

At home, it is easier to cut blanks of the required configuration from a sheet of plywood (any) or MDF of the desired thickness, or, twice or four times as many in quantity, from thin sheet material, in order to then gain as much thickness as required. Cut with a finishing allowance of approx. 1 mm. The cut blanks are tightly pulled together in a package in a carpenter's vice or in a locksmith's through gaskets made of thick plywood and processed with a rasp on wood to size, and then with a clean sandpaper. One rasp is enough, with flat and semicircular working surfaces, see fig.

The workpieces are assembled into parts in the manner described above. The end surfaces, if you need to hide the layered structure of plywood, are sealed with strips of self-adhesive film under the tree. After that, the part is varnished twice or thrice with water-based acrylic varnish; nitrolac can ruin the self-adhesive. It is not worth edging (edging) with a plastic furniture edge: you need to accurately select the groove for the edge anchor, which requires a milling machine, but on curved surfaces of large curvature and short length, the edge still does not hold well. And the details pasted over with self-adhesive, under varnish, from solid wood, even the master cabinetmaker will not immediately distinguish.

A hanger is an integral element of any hallway. This is what we see when we enter any home. To date, there is a huge variety of models of such furniture, but floor racks are considered the most popular.

Existing varieties

Depending on the design features and on the purpose, there are three types of these:

  • costume;
  • wardrobe;
  • hanger-rack for clothes floor (fits perfectly in the hallway).

Costume options are separate devices designed for storage business wardrobe. Such models usually consist of a rod or crossbar for trousers, hangers for jackets and shirts, and a separate tier on which ties are hung. More modern floor racks for clothes are equipped with additional shelves and movable or stationary mirrors.

Wardrobe models are impressive in size. The main purpose of this furniture is to store dresses and other clothes on hangers. As a rule, such models are equipped with a high-positioned bar to accommodate wardrobe items. A standard dressing room has two supporting legs with a crossbar in the middle. Multifunctional models have additional movable bars and crossbars.

The options used for hallways are made in the form of a high rack, in the upper part of which there are special hooks. The stability of this design is ensured by the presence of a small rounded base with several legs.

The materials from which such furniture is made

Modern floor racks for clothes are made of wood or metal. In some models, manufacturers manage to successfully combine parts that have different origins and textures. They are used for finishing natural materials(animal horns or different types of wood), plastic, painted or chromed metal.

Necessary tools and materials

If desired, such furniture can be made independently. To do this, you need to stock up in advance with a hacksaw, drills, drill, sandpaper, chisel, varnish and stain. From the materials we need:

  • bars;
  • wood glue;
  • boards;
  • self-tapping screws.

floor: we make furniture with our own hands

Boards and bars should be as dry as possible. Racks for clothes floor, made of low-quality raw materials, will quickly fail. Insufficiently dried wood will begin to release moisture, and the glue that holds the individual structural elements together will simply come off. best material for the manufacture of a hanger-rack, pine is considered. This wood does not require complex processing and has a relatively low weight.

The higher the finished product, the wider its legs should be. It is desirable that the product has at least three supports. Having decided on the model of the future hanger, it is necessary to draw its diagram, make preliminary calculations, measure the height and width of the structure. Having completed the description of the dimensions of all the details, you can get to work.

The process of manufacturing a floor hanger for men's suits consists of several stages:

  • cutting blanks according to a previously developed project;
  • careful processing and polishing of wooden elements;
  • drilling mounting holes in pre-designated places;
  • construction assembly.
  • finishing finishing;
  • screwing roller wheels or gluing rubber gaskets.

The final stage of work should be giving finished product aesthetic appearance. To do this, it is treated with stain and opened with varnish. So that drops of stain do not accidentally stain the floor, you need to do this on a special substrate. The varnish is applied only after the stain has completely dried. It is recommended to work with it outdoors or in a well-ventilated room.

Racks for clothes floor for shops

Such hangers are considered universal commercial equipment, which allows you to compactly place and sort the offered goods. They are easy to disassemble, do not take up much space and move around the trading floor without any problems. The use of floor structures greatly facilitates the process of familiarizing potential buyers with the assortment presented in the store. Trading racks-hangers can be one-, two- and three-tiered. Especially for the placement of fur and leather products, reinforced models are produced that can withstand the weight of such clothing.

Most manufacturers produce two types of such equipment - stationary and mobile. Stationary structures are installed directly on the retail space and do not move around the hall. Mobile racks are equipped with special wheels, so they can be easily moved from place to place. In almost all models, it is possible to adjust the height of the structure, which greatly facilitates the procedure for changing the assortment.

Ideas for making clothes hangers with your own hands: photos and drawings of hangers for the hallway. A variety of options for making homemade clothes hangers.

You can make a clothes hanger with your own hands practically from improvised materials that are lying around at home idle. Craftsmen do not cease to amaze with their ingenuity, here is a clear example of this, a home-made clothes hanger from ordinary forks.

A similar version of a hanger made of metal spoons.

Pallet clothes hanger.

Here is a clothes hanger from a pallet, and again the old pallet was used. A wooden pallet is sawn into two parts from each half of the pallet, you can make a hanger, just paint the workpiece and attach hooks to the boards with screws.

Another option for a pallet hanger, here a whole wooden pallet, it is sanded with sandpaper, the boards are painted in different colors and attach hooks.

Wooden clothes hanger.

Such a hanger is more suitable for a summer house or a bathhouse; wooden knots fixed in a wooden structure are used as hooks here.

Hanger made of metal profile and bars.

The design consists of several bars and metal profiles fastened together.

Wooden hanger with your own hands.

Here a wide board with imitation of a piece of old wood is used, hooks for clothes are made of bars and fixed with screws screwed in from the back of the board.

The wood is burned with a blowtorch, which achieves the original texture of the product, the final stage is coating the hanger with a transparent varnish.

In this version, there was no carving work.

And in this design, instead of hooks for clothes, door handles are used, which can also be coated with paint.

An interesting option for hangers from boards.

Original homemade hanger in the form of a tree.

For manufacturing, thick plywood is used, the contour of the tree pattern is drawn and cut with an electric jigsaw. The design is painted and attached to the wall with dowels.

Hangers for children's clothes.

The details of the hanger are cut out of plywood with a jigsaw and painted with bright colors, so you can make a hanger in the form of animal figures.

Do-it-yourself outdoor clothes hanger.

The simplest version of a floor clothes hanger made of pipes, for manufacturing you will need a thin aluminum pipe 2–2.5 m long. The pipe must be bent, as shown in the figure, and the clothes hanger is ready.

Wall hanger made of pipes.

And this hanger consists of a picture on the wall, clothes hooks are attached with dowels directly to the wall.