Do-it-yourself shower: camping, country options and designs Do-it-yourself shower-treadmill: device and main characteristics Do-it-yourself camping shower

25.04.2020

On long trips, showering is usually a luxury, especially if the hike is completely self-contained. But even in the field, you can arrange a primitive shower. I propose to spend 10 minutes of your time and make a camping shower from a bottle and a dropper with your own hands.

Our homemade camping shower weighs only 8 grams, it is universal (fits any PET bottle with a standard neck), takes up minimal space, and its design is very reliable. Making such a shower is very simple, and the cost of manufacturing is cheap.

We will need: a dropper system, a small clerical clip, a cap from a PET bottle.

Additionally: a 1.5-2 liter bottle of mineral water, 2 guys from the tent or other ropes.

Tools: drill, knife, tape measure, marker, 2 drills for 1.5 mm and 4 mm.

We cut off 40 cm from the dropper tube (the length of the entire tube is 120 cm - enough for 3 showers). With a marker, we mark the places of future holes on the cork from the bottle: a large one in the center and 7 small ones in a circle.

We drill the central hole with a 4 mm drill, the rest we drill with a 1.5 mm at a slight angle so that the water then flows a little to the sides.

We pass the tube into the central hole. We specifically took a 4 mm drill - a diameter equal to the tube, so that the tube fits snugly into the cap. But there will be no need to additionally seal the gaps.

We put a clerical clip on the protruding end of the tube. Ready

Now about how to use. An ordinary 1.5-2 liter bottle of mineral water is suitable as a reservoir. We take two braces from the tent, make loops out of them, thread the neck of the bottle into one loop, wrap the bottle around the second loop and tie the end of the first loop to the second, as shown in the photo:

The suspension is ready, now we fill the bottle 2/3 cold water and carefully add 1/3 hot. We twist our shower onto a bottle. Please note that the valve with the clerical clip must be closed during this. All that remains is to turn over and hang our camping shower on a tree or bush.

To “turn on” the shower, simply remove the clerical clip and the water starts to flow, if during water procedures we need to stop the water, respectively, put the clip in place.

Perhaps the only drawback of such a shower is its small volume, one and a half liter bottle enough for 2 minutes of continuous work. So, you have to take a shower quite vigorously 🙂

Walks in nature, night hikes, tent camps or just an unfinished dacha... What do these seemingly completely incompatible places have in common? One little nuance, from which it is difficult to refuse a person accustomed to the benefits of civilization. Namely - in any, as they say, Spartan conditions, it is impossible to accept water procedures. In a simple way, you can’t take a shower in nature or in unfinished infrastructure. Sometimes this becomes a problem that does not allow you to relax normally and plunge into the atmosphere of a real holiday. Without looking ahead, we can say: the problem is being solved! How? Another, no less interesting question.

Camping shower

Yes, what inventive people just do not come up with. marching country shower that is no exception. Why "dacha"? The fact is that often, looking behind the fences of gardeners, you can see a simple structure that is taken out every evening and brought into the house. That's why they called her the dacha.

But the lack of benefits on a favorite piece of land does not limit the possibilities of the above invention. Hiking, long walks, overnight stays - such a necessary thing as a camping shower can come in handy everywhere.

An easy choice

The needs do not go unnoticed, so the "smart" Chinese have learned how to mass-produce these designs. A camping shower can take any form, for every taste and for every preference. Need a closed type - please. The tent with a built-in tank is already ready for use. It remains to pour water. Ten, fifteen and even twenty liters are at the disposal of a clean traveler. There are also lighter designs: a frame with cellophane curtains, at the top of which you can see a small barrel.

A camping shower of this type has no disadvantages. Among the advantages can be considered lightness and low cost. All of these options are good for hiking and commuting, but it begs the question, “Why buy?” It's no secret that the need for invention is cunning. Don't pay money for something you can build yourself. For example, you can make a camping shower with your own hands. He will perform his functions as well as his commercial "brother".

How to make a camping shower with your own hands

You should not reinvent the wheel in this matter, everything has long been invented and tried. There is only one task - to make a good do-it-yourself camping shower, which should have such properties as ease of construction, low cost (it is desirable that all materials for the construction are at hand) and relative comfort.

First building

How to make a camping shower when there is almost nothing around, only nature itself? It doesn't matter, simple options will always find their use. Everything ingenious is elementary. The same can be said about the designs of the soul. The first thing that comes to mind for such a case is plastic bottles. Yes, there are no limits to fantasy. To build a camping shower from plastic bottles, a lot of material is not required.

First and foremost is capacity. The bigger it is, the better. After all, the water will flow longer, which means that the soul will be enough for a leisurely bath. Ten or five liters with proper and rational use is enough. So, there is an eggplant. We need to start building. This option will be the most comfortable, so you have to work. An empty container should be placed just above your own height. Otherwise, when taking a shower, you will have to bend down, which is not very pleasant. But here it is important not to overdo it, otherwise the procedure for filling the eggplant with water will take a lot of time and effort. In the "shower" capacity you need to make a small hole. Water will flow out of it. You need to insert a small hose into this hole, it will be easier to take a shower with it. There will be no need to wriggle in front of the jet. It is desirable to process the joints well with resin or plasticine so that water does not seep through. The first do-it-yourself camping shower is made. Of course, you can add something of your own to it, it's up to fantasy.

Second building

There is the most reliable and proven method, which, probably, everyone used. This is a bucket. No, you should not pour it in one gulp: there will be little effect. This design needs to be redesigned. A couple of actions - and from the bucket you get a camping shower. For this design, you will need a few tools and materials: a drill, a large and long bolt, emery, a nail and a nut (of course, the same size as the bolt). So, in a bucket with a drill, you need to make a hole. If such a thin tool is not at hand, a hole can be made with a nail.

But it will not be neat, so the edges should be further processed with emery. It remains for small: to thread the bolt into the hole and not completely tighten the nut. Thus, a large washbasin turned out. Raise the bolt - water flows, release - water does not flow. This is very convenient, because the liquid does not run in vain, only when it is needed.

How to arrange a shower

Usually a camping shower is built for a short time. Day, two - no more. Therefore, many are not too worried about the arrangement of the structure. But when it comes to constant use, you really need to rely on convenience. For example, shower curtains.

They will add home comfort. Curtains must be waterproof. The tape fits perfectly. How to fix it? Around the tree, with the help of branches, you can pull a rope, and hang a curtain on it. You should carefully examine the place near the shower. There should be no extra branches, needles, thorns, splinters and cigarette butts. Taking a bath next to garbage is not only unpleasant, it can be harmful to health.

In our time, it is not at all necessary to relax in nature or while traveling to deny yourself such pleasure as bathing in the shower. After all, you can find a camping shower on sale - 12 volts from the car will power the water pump, so you can wash yourself. And for backpackers, compact portable devices are offered that are completely non-volatile, and below we will get acquainted with all the most common types of camping showers that will make your stay in nature more comfortable and enjoyable.

Types of camping showers

Depending on the type of construction, all existing types of showers can be divided into several types:

Portable cabins with tanks;
Portable containers without booths;
Shower pumps.

Below we will take a closer look at all of the above types of devices.

Camping cabins

The camping shower cabin is a collapsible structure, covered with an awning according to the type tourist tent. This option is excellent choice for people who like to relax in nature for a long time "savages". In addition, camping cabins are widespread among summer residents who visit a suburban area in the summer.

As a rule, such booths are equipped with tanks of 20 liters or 40 liters. Some models are equipped with a pump for pumping water into a container from a source, such as a bucket or even a pond.

Most often, the water in the tank is heated natural way, i.e. due to the energy of the sun, or the container is filled with preheated water. True, on sale you can find tanks with electric heating. They are more comfortable to use, but their disadvantage is volatility.

Camping showers usually weigh 2.5 - 3 kg, and when assembled, the product takes up little space, which is especially important for travel lovers.

Advice!
When choosing a camping cabin, you should pay attention to its equipment.
Often, a clothing rug and other accessories are attached to the product.

Portable containers

Portable shower tanks are the most simple devices, which consist of only two main elements:

A 25 liter tank, usually soft, made of PVC.
Hose with sprayer.

To use such a device, you only need to hang it with your own hands on a tree, pole or fix it in a booth. It should be noted that portable containers also come with and without a water heating function.

As for the volume of the tank, as a rule, 20-25 liters is enough for one person to bathe. The advantage of such products is the low price and minimum dimensions.

Shower pumps

A distinctive feature of these products from the above shower systems is that they do not require the installation of a container at a certain height, since water is supplied to the watering can using a pump.

It should be noted that these systems are of two types:

Electric, working from 12V- products were originally designed for motorists, so they can work from the cigarette lighter. The design is a small electric pump with a watering can. As a container for water, you can use any bucket, canister or barrel.
Mechanical ("toptun")– This hiking shower is a rubber mat with two built-in pumps. In the process of bathing, a person steps from one foot to the other, resulting in water from under a certain pressure. The advantage of such a system is energy independence, however, such a device is less convenient in operation.

Note!
The instruction manual for the car shower implies its use from the cigarette lighter with the engine running.
Otherwise, battery discharge may occur.

In the photo - a mechanical shower "toptun"

Homemade construction

If you do not have a ready-made portable shower device, then to take water procedures, you can make the simplest do-it-yourself shower in camping conditions.

For this you will need:

Plastic bottle with a capacity of 5 liters;
Wire;
Hose;
Curtain.

The design is made as follows.

A hole is cut in the bottle cap and a hose is inserted. To fix it, on the inside of the cap in the hose, make a hole perpendicular to the walls of the tube and insert a nail or wire.
Then in the bottle you need to cut the bottom and make two holes in the walls.
Next, you need to make a handle or hook from the wire and fix it in the holes, which will allow you to hang the bottle on a tree branch.
Then, at the tip of the hose, you need to make a hook from the wire, which will allow you to cling to the wall of the container and thereby block the water supply.
After making the shower, you just need to hang a curtain, which will allow you to hide from prying eyes.

You can also make a do-it-yourself shower with a pump like a “treadmill”.

For this you will need:

Car foot pump;
Hermetically sealed container;
Hose, preferably with a shower head.

Now let's look at how to make a shower on a hike with a foot pump:

First of all, you need to cut two holes in the container lid and insert the hoses. Moreover, the connections must be tight, so rubber gaskets or other seals should be used.
Then it is connected to one hose car pump, and to the other - a shower head.
After that, you need to fill the container with water and you can check the device in action. In order for water to enter the watering can, you need to perform several strokes with the pump.

This design is more complex, however, more convenient to use, especially if you use the shower together. In this case, one person can take a shower, and the other can pump water with a pump.

Conclusion

Portable showers can significantly increase the comfort of outdoor recreation or travel. Moreover, they can be both extremely simple containers with a watering can, and folding showers. True, as we found out, in the absence of a portable shower, you can make a bathing device yourself from improvised means.

From the video in this article you can find some additional information on this topic.

When it comes to making such a structure as a shower, usually craftsmen imagine a booth with a pallet connected to the water supply, or on which a water tank is installed. However, if finished products cannot be found, then you have to use any improvised material or products with a different purpose. Therefore, the question of how to build a shower with your own hands using the minimum number of elements required for this is interesting even for experienced professionals.

hiking options

Going to rest in nature, a person tries to provide for himself on the spot. maximum comfort. At the same time, you should not carry a lot of things with you, and when loading the car there are a lot of necessary items that you need to take with you. Therefore, a typical tourist shower should take up minimal space, be light in weight, or be made from existing items with a different purpose.

Shop designs

Of all the existing models of systems for this purpose, it is worth noting only one. It looks like an ordinary tight package, to which is attached a small valve with a detachable watering can and a hatch with a lid for filling. It should be noted that the price of such a design is quite small, and it takes up minimal space, weighing almost nothing.

Such a product is filled with water and hung on a tree. Then, opening the valve, they begin to use it as a regular shower. It is worth noting that the instruction manual allows you to use even hot water, but each specific model has its own tolerances.

Given the features of this design, it can be attributed to the camp. At the same time, you can create a similarity of this device yourself using a tarpaulin or film.

Advice!
A similar system can also be used for transportation and storage drinking water.
Therefore, the need for her in campaigns is obvious.

Homemade products

Most tourists make an elementary shower from a canister with their own hands, without damaging the products. It is enough just to have an additional cover with you, in which holes are made in advance. It is put on after filling with water and used in.

You can also use large plastic bottles or other similar containers. However, if there is a strong need, it is easiest to use a teapot, on the spout of which watering cans are put on and hung on a tree. Such a shower in nature with your own hands can be built in a few minutes.

Advice!
There are many ways to organize the supply of water from a height, but you can only spray a jet from a watering can.
Therefore, it is worth taking with you.

Country designs

Creating a shower on the site with your own hands, you have to face a number of problems that need to be solved taking into account the terrain and the expected level of necessary comfort. Therefore, the manufacturing process should be divided into stages.

Pallet

The easiest way is to make a pillow with gravel and sand, on top of which they install. This is how they usually do a shower in the village with their own hands, assuming that the drain will go straight into the ground.
It is also a fairly common method of making concrete base . You can pour it yourself or use a ready-made plate for this. At the same time, a slope must be made in the direction of the intended water drainage. Some masters simply use stones that are tamped into the ground to simplify the work.
If you make a shower with your own hands, then you can use any available materials. The main thing is that they can be easily walked on even in the presence of water, and there was an opportunity to organize a drain.

Advice!
The outflow of water must be done so that the liquid goes into the ground, and not under the foundation of the building.

Tank

When they make a shower in the yard with their own hands, then you should immediately think about what container you need to use for water. This is especially important if it is not possible to purchase a standard tank.
It should be noted right away that the barrels in which they used to be chemical substances or petroleum products are not suitable for these purposes. They may leave a residue, which then dissolves in water and can lead to poisoning of the body.
Also, do not use open containers. They can get sick birds or their waste products.
The easiest way is to make a do-it-yourself shower from a Eurocube, since this container is excellent in all respects and at the same time has sufficient volume. However, it is necessary to take into account the large weight and use strong supports during installation.
A tank for such purposes is selected very carefully, since this is the basis of the whole structure and it will depend on it. appearance frame.

Advice!
Installing a faucet with a watering can is quite simple, but it is worth remembering that it is best to use a screw or needle locking mechanism.
These systems allow you to precisely adjust the force of pressure, which significantly increases the level of comfort.

fencing

Some masters prefer to create the simplest overlaps using ordinary film. However, if done solar collector for a do-it-yourself shower, it is assumed that the structure will be in the open air and light will penetrate through it. This causes some discomfort for some people as the interior space will be viewed.

Advice!
Sometimes old Construction Materials great for this task.
However, they must be put in order and subjected to protective treatment.
This can be done with regular paint.

Structures in the apartment

Sometimes situations arise when it is necessary to equip a shower in an apartment, but it is not possible to install a cabin. Then you can apply specially designed designs or non-standard technical solutions.

Bath

The easiest way to install a shower in the apartment with your own hands, if it is located in the bathroom. You can use the bowl itself as a pallet, but at the same time, in the places where it comes into contact with the wall, all joints must be sealed using sealant. It is also assumed that the installed faucet will have a shower head that will be able to be fixed on the wall.

Next, you should purchase a special fence or curtain that will protect the room from splashes. At the same time, it can completely cover the entire perimeter or only the bath, which is located a meter from the mixer.

Advice!
Such solutions are quite simple, since they have been used for a very long time and some companies develop a lot of products for them.
However, when choosing them, you need to be very careful so that all the elements are perfectly combined with each other into a single system.

Toilet

Even in our time, there are still apartments in which there is simply no such room as a bathroom. There are also situations when people buy a room in a hostel and want to get their own amenities, saving space. Therefore, in such cases, a shower room is made in the apartment with their own hands, but it is connected to the toilet.

First of all, in such situations it is necessary to drain. At the same time, in sewer pipe they cut a branch, which is bricked into the floor screed with waterproofing, making it look like a storm drain at an angle. Of course, the level of the threshold and the floor will rise greatly, but this is a necessity that cannot be avoided.

Next, just install a mixer with a shower head on the wall. In such a room, you can safely take water procedures. In this case, the closed toilet seat will serve as a kind of chair, which is very convenient for some people.

Advice!
Such a solution can be called extreme, but under certain technical conditions it is the only one.
However, if it is possible to use the cabin, then it should be used.

At the time when it comes to the manufacture of such a structure as a shower, in most cases, the craftsmen imagine a booth with a pallet connected to the water supply, or on which a water tank is installed. But, if the finished product cannot be found, then you have to use any improvised material or products with a different purpose. Based on this, the question of how to build a shower with your own hands using the maximum number of elements required for this is also fascinating to skilled experts.

hiking options

Going to rest in nature, a person tries to provide himself with great comfort on the spot. Along with this, carry a large number of things are not needed, and when loading the car there are a lot of necessary elements that you need to take with you. Based on this, a typical tourist shower should occupy a minimum space, have little weight or be made from existing things with a different purpose.

Shop designs

Of all the existing models of systems for a similar purpose, it is necessary to emphasize only one. It has the form of a simple tight package, to which is attached a small valve with a detachable watering can and a hatch with a lid for filling. Along with this, it is worth emphasizing that the price of such a design is small, and it takes up minimal space, actually weighing nothing.

Such a product is filled with water and hung on a tree. After that, opening the valve, they begin to use it as a simple shower. It is worth emphasizing that the instruction manual allows you to use in addition warm water, but any particular model has its own tolerances.

Given the features of such a design, it can be attributed to the marching one. Along with this, it is possible to create a similarity of this device yourself, using a tarpaulin or film.

Advice! A similar system can also be used for the transport and storage of drinking water. Based on this, the need for her in campaigns is obvious.

Homemade products

Most tourists make an elementary shower from a canister with their own hands, along with this, without damaging the product. It is enough with an additional cover, in which holes are made in advance. It is put on after filling with water and used as a watering can.

In addition, it is possible to use huge plastic bottles or other similar containers. But with a strong need, it is easiest to use a kettle, on the spout of which they put watering cans and hang it on a tree. Such a shower in nature with your own hands can be built in a couple of minutes.

Advice! There are quite a few ways to organize the supply of water from a height, but it is possible to spray a jet only from a watering can. Based on this, it is worth taking with you.

Country designs

Creating a shower on the site with your own hands, you have to face a number of troubles, decide which ones you need, taking into account the terrain and the expected level of comfort you need. Based on this, the manufacturing process should be divided into stages.

Pallet

The easiest way is to make a pillow with gravel and sand, on top of which they install wooden pallet . So in most cases they make a shower in the village with their own hands, assuming that the drain will go straight into the ground.
In addition, the method of manufacturing a cement base is quite common.. It is possible to fill it yourself or use a ready-made plate for this. Along with this, it is mandatory to make a bias towards the proposed drainage system. Some masters to simplify the work of stones, which are tamped into the ground.
If a shower is made by hand, then it is possible to use every improvised materials. The main thing is that it was easy to walk on them, in addition, in the presence of water, and it was possible to organize a drain.

Advice! The outflow of water must be done so that the liquid goes into the ground, and not under the foundation of the building.

Tank

At the time when they make a shower in the yard with their own hands, then it’s worth thinking about what kind of container you need to use for water. This is especially important if it is not possible to buy a conventional tank.
Immediately it is worth emphasizing that barrels in which chemicals or oil products were previously not suitable for these purposes. They may leave a residue that will later dissolve in water and can lead to poisoning of the body.
In addition, open containers should not be used. Sick birds or their waste products can get into them.
The easiest way is to make a do-it-yourself shower from a eurocube, because this container is excellent in all respects and at the same time has a sufficient amount. But you need to take into account the enormous weight and use strong supports during installation.
A tank for similar purposes is selected very carefully, because this is the base of the entire structure and the appearance of the frame will depend on it.

Advice! It is quite simple to install a tap with a watering can on the container, but you should not forget that it is better to use a screw or needle locking mechanism. These systems allow you to precisely adjust the force of pressure, which significantly increases the level of comfort.

fencing

Some masters prefer to create the simplest overlaps using a simple film. But, if you make a solar collector for the shower with your own hands, then it is assumed that the structure will be in the open air and light will penetrate through it. This leads to a certain discomfort for some people, because the interior space will be viewed.

Given this feature, experts advise using profile pages either moisture resistant plywood. In addition, dry reeds are suitable for these purposes, which are tied together, creating a full-fledged overlap.

Advice! Sometimes dilapidated building materials are perfect for such a task. But they need to be put in order and subjected to protective treatment. A simple paint may work for this.

Structures in the apartment

Sometimes such situations arise, at a time when you need to equip a shower in an apartment, but along with this there is no way to install a cabin. Then it is possible to use intentionally created designs or non-standard technical solutions.

Bath

The easiest way to install a shower in the apartment with your own hands, if it is placed in the bathroom. It is possible to use the bowl itself as a pallet, but along with this, in the places of its contact with the wall, all joints must be sealed using sealant. In addition, it is assumed that the installed faucet will have a shower head that will be able to be fixed on the wall.

Then you should buy a special fence or curtain that will protect the room from splashes. Along with this, it can completely cover the entire perimeter or only the bath, which is located a meter from the mixer.

Advice! Such solutions are quite simple, because they are used in a very distant past and some companies develop a lot of products for them. But when choosing them, you must be careful so that all the elements are perfectly combined with each other into a single system.

Toilet

In addition, in our time there are still apartments in which there is no room like a bathroom. In addition, the environment is seen at a time when people buy a dorm room and want to take personal comfort while saving space. Based on this, in such cases, a shower room is made in the apartment with their own hands, but it is connected to the toilet.

First of all, in similar situations, you need to drain. Along with this, a branch is cut into the sewer pipe, which is walled into a floor screed with waterproofing, making it look like a storm drain at an angle. Needless to say, the level of the threshold and the floor will rise very much, but this is a necessity that cannot be avoided.

Then just install a mixer with a shower head on the wall. In such a room it is possible to take water procedures normally. Along with this, the closed toilet seat will serve as an unusual chair, which is quite convenient for some people.

Advice! Such a solution can be called extreme, but in certain technical conditions it is the only one. But if it is possible to use just the cabin, then it should be used.

Conclusion

After reviewing the video in this article, it is possible to study in more detail these designs and the principle of their manufacture. In addition, taking the text above as a base, it is worth concluding that, in fact, in arbitrary conditions, human ingenuity allows you to create designs that can significantly expand the level of comfort.

Along with this, making a shower with their own hands from improvised materials, the masters take into account all the wishes of future users. This gives rise to the most extraordinary designs with fantastic designs and technical highlights.