coupe 

Tasty tank for 1 spiral. Top atomizers. According to the degree of resistance of the spiral

Tanks and clearomizers

Every vaper sooner or later wonders what is the best tank for electronic cigarettes. Let's start with the fact that tanks are a device where the steam mixture is generated into steam.

That is why vape users want to choose the most best tanks, due to which it is possible to organize the process of soaring more qualitatively. And yet, which tank for electronic cigarette it is better? This is what we will try to deal with you now.

  • serviced (RTA);
  • serviced drip (RDA);
  • genesis.

There is another category of serviceable atomizers - RDTA, drips that you can service yourself. But in this publication we will talk about ordinary tanks. All of these vaporizer options are equipped with coils, which can be either purchased at a vape shop or twisted on your own.

So, what are serviced tanks. As a rule, most of these evaporators have a base on which, in fact, the heating element (our coil with a wick) is placed. Whereas the tank itself with the vapor mixture is located above the base. Depending on the size of the tank, it can hold from 2 to 10 ml of liquid.

Most of these evaporators, released recently, are equipped with top airflow. The principle of operation in this case is as follows: the air first of all descends to the winding outside the chamber, and only after that it goes up through it, that is, to the drip-type.

The bases of serviced tanks are equipped with slots or holes, through which the vaporized liquid rises through the wick to the heating element

Drips, unlike tanks, have a small bath for refilling, respectively, less liquid will interfere with them. Heating coils are also located at the bottom of the evaporator, and the wicks are immersed in the recharge bath.

In addition, the drip does not have a chamber, since the vapor mixture is in any case below the spirals. Instead, the RDAs are equipped with a top cap that sits on top of the base. Air enters through the bottom, top or side vents and rises from the top cap to the drip tip.

Genesis atomizer is a combined evaporator in which a drip and a tank are combined. They have a capacity similar to the RTA, but they are located at the bottom of the atomizer, under the base. Due to this, the effect of having a deep bath is achieved.

A rolled stainless steel mesh acts as a wick, through which the steaming mixture enters the winding. In addition, Genesis, like drips, has a top cap. Yes, and air circulation occurs according to the principle similar to drips.

Tank Advantages

First of all, I would like to note the advantages of serviced tanks over unattended ones - a vape user does not need to purchase factory coils, they can be made with my own hands. This not only allows you to save on winding electronics, but also gives you the widest possibilities when vaping (the larger the winding area, the more steam it produces).

If we compare tanks with drips, then the former have the following advantages:

  1. The volume of the contained vapor mixture.
    It's no secret that RDAs are drip-filled, that is, they drip a certain amount onto the winding and soar for 8-10 puffs. The tank is good because, as mentioned above, up to 10 ml of liquid is placed in its tank. This means that you can use the vape between refills almost all day (it all depends on the frequency of vaping).
  2. If the vape is not standing vertically, then, in the case of a drip, it may leak.
    Whereas with the tank, the electronics will not leak. This is due to the fact that there is no camera in the drips, but there is one in the tanks.
  3. Compared to drips and genesis, tanks are easier to wind.
    At least the owners of genesis note that they always have to take care of the correct oxidation of the mesh and determine the hot spots where the mesh will come into contact with the heating element.

To make it easier for you to decide which serviced tank to choose, we offer you our top 5 most popular vaporizers for electronic cigarettes.

Pharaoh by Rip Trippers/Digiflavor

The diameter of this tank is 25 mm, and on its base you can install a single or double winding of a wide variety of configurations. The base itself is equipped with two racks with spring clips for fixing coils. The single wick and opening can be closed and opened by the user of the electronics as needed.

This vaporizer model provides the vaper with the widest airflow adjustment options. This is due to the fact that the tank is equipped simultaneously with three central rectangular holes, the size of which is 5 * 2.5 mm. Thanks to this, both a hookah puff and a tight cigarette puff are possible.

For stable use of the TK mode, the positive connection was gold-plated during the manufacturing process. And thanks to the presence of a PEEK insulator, high vaporization is ensured.

Such a tank is perfect for those vapers who are looking for a brand new, interesting and tasty atomizer for their electronics.

Advantages:

  • the presence of a multifunctional base opens up a wide range of vaping opportunities for the vaper;
  • the possibility of equipping the base with creative windings;
  • ease of maintenance, namely in the installation of wicks;
  • good taste qualities of the given steam;
  • the possibility of a hookah puff, as well as a tight cigarette;
  • good steam generation.

As for the shortcomings, there is only one – for some vapers, a 2 ml tank is not enough.

And in all other respects, these tanks are considered one of the most popular atomizers of our time.

Griffin 25mm RTA by GeekVape

An improved vaporizer model from the world famous GeekVape, which appeared before vapers in a new 25mm version. 2 versions were released: with top airflow and no airflow at all.

The base of this tank can still be equipped with one or two coils at the same time, but unlike the old version, now its size is 17 mm.

In this version of the atomizer, the volume of the reservoir is already as much as 6 ml, which is twice as large as the previous Griffin. These vaporizers are suitable for both experienced vapers, and even novice vapers who have just begun to comprehend the intricacies of such a truly fascinating culture as vaping can handle them.

Advantages:

  • high-quality veloci-stands with holes for fixing the winding Ø5 mm;
  • the possibility of soaring in temperature control mode;
  • the presence of a gold-plated 510 type connector and a PEEK insulator ensures a stable connection between the tank and the vape itself;
  • a sufficiently large volume of the tank for refueling;
  • the ability to use various drip types;
  • providing fantastic taste and a decent vapor cloud;
  • ease of installation of spirals and wicks.

Of the shortcomings, only that this tank is a bit tall.

Avocado 24 by GeekVape

A modern tank, the diametrical size of which is as much as 24 mm. This evaporator model is equipped with high-quality velocity stands, with which you can securely fix the coils on the base.

The size of the opening for the wicks is 4 mm, which allows even beginners to use such devices. As for the volume of the reservoir, this advanced model includes as much as 5 ml of liquid.

Innovative dual 3mm refill ports with pivoting lid make refilling simple and easy. In addition, Avocado provides the ability to adjust the size of the air duct opening: if they are fully opened, then their size will be 7 * 2 mm. To change the size of the holes, just rotate the top cap.

In addition, the tank is equipped with a ceramic insert that can be installed instead of one of the coils. Thanks to the convenient base and ease of maintenance, the Avocado 24 will appeal to everyone, from a novice vaper to a professional.

Advantages:

  • getting a bright taste of steam even with an active one spiral;
  • excellent vaporization when using two spirals;
  • ideal price / quality ratio;
  • wide range of vaping options;
  • the possibility of soaring like on a drip;
  • due to its small size, this tank will perfectly complement almost any vape;
  • Due to the possibility of complete disassembly, this vaporizer can be completely washed after use, which greatly extends its service life.

Disadvantages:

  • this tank may leak if dropped.

Another vaporizer that is very popular among pro vapers. In terms of performance, it has certain similarities with the Geekvape Griffin tank. It is easy to use, has a spacious base that can easily fit two coils.

This tank is mostly designed for aroma transfer, but can also be used for sub-ohm vaping.

Advantages:

  • convenient and affordable design;
  • simple and spacious base with the ability to install a pair of spirals;
  • convenient refueling process - top;
  • high rates of vaporization and taste transfer;
  • ease of installation and assembly.

Disadvantages:

  • it is not intended for releasing huge clouds of steam, that is, it is better not to take this tank for cloud chasing.

Kayfun v5 by SvoeMesto

The tanks of this manufacturer are valued by their owners for their excellent transmission and wide possibilities for adjusting the vaping process.

Advantages:

  • the widest range of airflow adjustment;
  • you can buy a tank in stainless steel or glass;
  • high quality construction, which leads to a long service life;
  • the possibility of equipping the base with large spirals;
  • excellent flavoring.

Of the shortcomings, only that there is no hookah puff on this tank.

If you use an electronic cigarette with a tank, then here are a few good advice on the use of such gadgets:

  1. In order for the vaping process to be of high quality, you need to make sure that the coil covers the air duct opening, especially in atomizers with a bottom airflow.
  2. Coils that are too short will cause liquid that drips onto the wick to enter the blow hole, resulting in gurgling and leaks. To prevent possible vaporizer leaks, you need to make sure that the vapor mixture does not drip freely onto the base past the tails of the wick. The latter should optimally block the holes for the liquid.
  3. If the tank starts to vape dry, it means that you have overdone the blockage and prevented the liquid from moving. To balance the vaping process, you need to replenish the tank with filling in a timely manner and monitor the level of liquid in it.
  4. Bucky will be the most suitable option for the first vape on serviced vaporizers, since most of these gadgets allow the vaper to reach the base at any time to reinstall the wick.
  5. And, lastly, make sure that the container is not overfilled with vaporous liquid. There should be some air left in it, due to which the liquid can evenly soak the tails of the wick. It also causes the timely replacement of the evaporated liquid with air.

Summing up

Bucky - great alternative regular atomizers. They are roomy, tasty and give out a lot of steam. In the case of serviced evaporators, it is easier to wind the bases yourself, and it will be cheaper in terms of money. Maintenance-free tanks after use (which is 6000-8000 puffs) are subject to disposal, and there is no possibility of varying the characteristics of the coils on them.

From the top tanks offered above, you can choose for yourself the device that will definitely be able to satisfy your vaping needs. What vaporizer do you think is the best to use on electronic cigarettes?

Hi all. Another review on the subject of electronic cigarettes. I still spend 200-300 rubles per month on liquid (taking into account the tight puff), and I think it's just great, such a savings compared to analogues ... What has happened and changed in the electronic cigarette market lately? The trend is now tanks with an upper air intake, but at the same time the air passes through the entire tank and blows the spiral from below, or from the side, changing the trajectory. And I think that such a design fully justifies itself, firstly, there will be no leaks, and secondly, there is a full-fledged lower airflow, which will positively affect the taste. An example of such tanks: Horus RTA, Solomon 2, OBS Engine 2. The Intake atomizer was released by Augvape, together with the famous reviewer Mike Vapes, the tank was a success, but I still had questions.

To start, some useful information:
1. reviewer Mike Vapes. As far as I understand, he had a hand in the design, constructive, and the Chinese guys from Augvape implemented all this and started selling. They seem to be running out of ideas.
2. The tank is available in four colors.

Additional Information


3. Made of stainless steel, there is a pot-bellied glass in the kit, with it the volume of the tank will be 4.2 ml of liquid, with flat glass: 2.5 ml.
4. Diameter: 24mm, Height: 50.5mm. Airflow adjustment: top, one spiral.

Let's move on to the review, let's see what Mike Vapes has prepared for us :)


Design / structure of the atomizer:

The atomizer comes in a thick, cardboard tube, like all the latest devices from Augvape. There is brief information on the box (links to social networks, contact address, etc.)


In the kit we will find: a spare flat glass (2.5 ml), o-rings, a dense lining for the top cover, a triple screwdriver, 2 screws for attaching the coil, a spare 810 drip-tip and an adapter for 510 drip-tip.


Weighs 57 grams without winding and liquid:


The tank has an 810 drip-tip fit, with a low acrylic drip-tip preinstalled.


Optionally, you can put a spare, but I did not like it.


You can also install an adapter and use any 510s, or pick up your 810s without an adapter. There is complete freedom of choice. But the stock low drip tip is quite good.


Next comes the top cover, which has no thread. There are convenient slots for gripping, slightly move it counterclockwise and it is removed. Under the lid there is a tight pad so that air does not enter the tank itself, that is, it is completely sealed.


If at first everything is fine, then on the second and third refueling you notice that the liquid then got on the lining, and the lid moves without much effort, slides. This is perhaps the only negative of the tank. The lid is very weak.


Under the lid, everything is standard, there are 2 filling holes. The filling area is flat, and you need to fill the atomizer carefully, as there are no sides.
There are 2 air intake holes below. There is a blower adjustment ring with a stopper, it has knurling for easy tightening adjustment.


The ring moves too freely because the o-ring is too thin underneath. The problem is solved, just select the o-ring a little thicker. And the ring has grooves, it won’t be possible to put it on somehow differently, for example, upside down.
You can change the cotton wool or spiral without pouring out the liquid, just turn it over and unscrew the base.


The glass is easy to remove, and there is no such thing that it sticks to the o-rings, no, it is removed immediately.


On the dome there is an application "Intake". Changing glass:


There is a flat processing inside and it immediately becomes clear how the air passes, and it passes through two holes into which special tubes enter on the base itself.


At the same time, this entire platform is spinning in a circle, for the possibility of combining with the base.
The bottom pin is not adjustable. The positive pin sticks out normally, you can use it and wind it on the mechanics.


This is what the base looks like:


Everything is arranged here very simply, air passes through the tubes into special three holes of the lower airflow (that is, these three holes and the tubes themselves are combined), everything is much simpler than it might seem. Nearby there are two grooves, which by themselves are in no way aligned with the airflow holes, they are by themselves. There are two stands with screws for a Phillips screwdriver.
A small bevel, we drive the leg of the spiral and clamp it - it’s convenient.


The base is made very high quality, and at the same time it is very easy to wind.

For those who do not understand how the spiral is blown, this is clear and understandable:

Winding.
For convenience, first we select a spiral, it should cover all three airflow holes, and the legs of the spiral should also go into the holes of the racks. What to do, just take it on a piece of paper and mark the length with a pen or take a ruler. And you can also make one spiral (blank), along which you will wind a new coil each time for this tank. One of the inconveniences is that you need to wind it counterclockwise, I took the Fused Clapton, the mandrel diameter is 3 mm.


He slightly raised the spiral over the airflow, but just a little bit.


Next, cotton wool, left the ends by eye and fluffed it very well with sharp tweezers.


In fact, I leave a little less cotton in length than in the photo above.
Of course, the spiral turned out to be not quite even, but this does not affect the taste. I just remade the spiral for this base.


Leave the length as desired, someone leaves a little, someone a lot.

The set power is 48 watts, later raised to 55.

The liquid is 70 to 30, the flow is perfect, the amount of steam is good, the steam is thick, warm and there is a lot of it. What else I forgot to indicate: the diameter of the pot-bellied glass is 27 mm.

Opinion.
I liked the tank, it does not flow, I did not find a drop of liquid and condensate in the airflow holes. I can’t even imagine how to pour it, I put a negligible amount of cotton wool into the grooves and even in this case it didn’t drip. The tank from the box does not smell of anything, it seems that it was thoroughly washed, there are no smells, no production oil, no chips. Can be used immediately, there will be no foreign odors when vaping. The quality of the screws is normal, the threads are normal, the metal is processed well. The taste transfer is decent, of course it’s not a drip, but in terms of taste in its category, this is one of the best tanks.

Cons: easy to open filling cap, weak o-ring under the adjustment ring. And one imhovaya claim, I would like a little tighter puff. But what if you leave the design, but make a tank with a tighter puff, for vaping at 20-30 watts, it would be great (or generally stir up a cigarette case using this design for low power, 15 watts) And so, use Intake RTA below 50 I don’t see much sense in watts, there is a lot of air here, a large spiral is needed.
Tank experience: 3 weeks. As for the noise when tightening, it is not here, unpleasant sounds and whistling as such are absent.

Now the box mod connector always stays dry, there is no condensation on the bottom and that's great. I recommend the tank boldly, among single-coil hookah puffs - I have it in my favorites. As for the lid, it didn’t move by itself, pah pah (but theoretically it can)

This concludes, thank you for your attention.

The product was provided for writing a review by the store. The review is published in accordance with clause 18 of the Site Rules.

I plan to buy +9 Add to favorites Liked the review +14 +19 up

Today I got a tank for one coil Vapefly Horus RTA. The Vapefly company appeared on the market not so long ago, but has already managed to show itself well, thanks to the successfully obtained Galaxies cigarette box.

Horus RTA has chosen a different path and, in fact, should be the heir to such well-known atomizers as Zeus and Ammit. Let's take a closer look and see what happened in the end?

An ordinary copy of famous tanks or a really worthy novelty?

Packaging and equipment

up

The Vapefly Horus RTA atomizer comes in a box with all the necessary information printed on it. On the front side located the name of the device and the company logo, which are, as it were, on top of the picture of the tank itself.

On the back there is a code for checking originality, certificates, equipment and contact information for contacting the manufacturer.


Inside, we are greeted by a very rich equipment, thanks to which we can run the device right out of the box. Separately, I would like to note a micro-fiber cloth, which is not clear why it is needed here, because the device is declared as a non-spill.

It is also not entirely clear why the manufacturer did not combine the hexagon with an alien screwdriver, but put it separately. But basically, it's all bullshit.

Equipment

  • Vapefly Horus RTA x 1
  • Spare screws - 4 pcs.
  • Set of o-rings - 1 pc.
  • Alien branded screwdriver - 1 pc.
  • Hexagon - 1 pc.
  • Adapter for 510 drip-type - 1 pc.
  • Pre-wound spirals - 2 pcs.
  • Cotton - 1 sheet.
  • Microfiber - 1 pc.
  • 810 drip tip - 1 pc.
  • Instruction - 1 pc.

Appearance and parameters

up

I got a black atomizer with a bright orange drip tip for review. Options are also available in gray, steel and the so-called gold colors.

The painting is done qualitatively and will not peel over time. There are no decorative elements on the outer part of the case. Decorative element is located inside the flask itself and is made in the form of one of the eyes of the god Horus.

The tank itself turned out to be quite bulky and has a diameter of 25 mm. If you are critical of overhangs, then under it it is better to use mods with a central location of the connector.

On the reverse side, there is a well-protruding, adjustable gold-plated pin, thanks to which, if desired, you can use the tank even on a mechanical mod.


Options

  • Diameter: 25mm
  • Height with drip tip: 49.7mm
  • Height without drip tip: 42.7mm
  • Weight: 65g
  • Materials: Stainless steel, delrin

Design features

up

To begin with, it is worth paying attention to the quality of manufactured parts, which is at a very high level here. Everything is perfectly fitted to each other, there are no backlashes and creaks.

On all moving parts there are notches for more convenient use of the device. By default, a bright drip-type of the standard 810 format is installed in the atomizer, which allows you to replace it with your own. Also included is an adapter for the 510th drip-type.

The upper part of the atomizer consists of a cover, under which there are two filling holes and airflow adjustment rings. The lid is attached to the base on a conventional thread and has notches for more convenient use.

Inside the lid is a silicone ring that prevents leakage when twisting. Filling holes are wide, so there are no problems with filling here.

The airflow system in the tank is the most important of its chips, and the first thing it starts with is the air intake holes located on top. Their adjustment is carried out by turning the ring. This design completely eliminates leaks, which is definitely a huge plus.

One of the main features of this atomizer is the air supply shaft. Inside the dome, which freely rotates around the shaft, there is a plate with several types of holes, passing through which the air creates the so-called effect of volumetric blowing of the spiral.

Such a system has a very positive effect on taste. The spherical processing of the dome is completely absent here due to the non-standard design of the dome. Pyrex-glass is attached using an ordinary thread located on the frame.

The base in the Vapefly Horus RTA is quite standard and is designed to install a single coil. A wide central airflow hole, coupled with massive racks, allows even very massive spirals to be installed here.

The fixing screws are made with high quality and will not lick off over time. The base is fixed to the dome by means of a thread located on the frame. A separate plus is that it simply won’t work to install the base incorrectly and there are no problems with getting into the notches as in the same Zeus.

Peculiarities

  • Base: Two racks with the ability to install one coil
  • Airflow: Volumetric bottom
  • Drip tip: 810, adapter to 510
  • Connector: 510 gold-plated pin

Installing spirals and stacking cotton

up

Installing spirals with a certain skill will not cause any problems at all. Essentially, you simply install the legs of the coils into the grooves, press them down with screws, and then align the coil over the duct opening.

It is important that the spiral is located exactly in the center. This will allow you to get the maximum flavor. Cotton wool fits quite simply. It is enough to lay it exactly in the grooves and gently straighten it, not ramming too hard.

According to personal feelings, the racks turned out to be very comfortable.


Conclusion

up

At first, I was skeptical about the Vapefly Horus RTA, but after spending some time with it, I can safely say that I liked the tank.

The first thing you want to pay attention to is, of course, the quality of the workmanship of the parts. The paint does not peel off over time, and all the elements fit perfectly to each other.

The second is, of course, a volume of 4 ml, which allows you to get good autonomy, and convenient racks will allow even a beginner to use the tank without any problems.

As a separate plus, I would like to highlight the design of the non-spill, which is great for everyday use of the atomizer.

The disadvantages include a slightly less bright taste compared to the same Zeus and other similar single-coil tanks. As a result, we get an excellent everyday tank at a very affordable price, which will definitely find its fans.

pros

  • Workmanship
  • Volume
  • non-spill
  • Convenient stands


Warning: strpos() expects parameter 1 to be string, array given in /var/www/kolisnykzid/data/www/website/wp-content/themes/proffit/functions.php on line 273

Vaping (smoking electronic cigarettes) is becoming increasingly popular. The process is the inhalation of steam from a special tasty tank. The second name of this element is a tankomizer. There are a lot of low-quality analogues on the market, so it is important to know the features that people pay attention to when choosing a product. For a better understanding, it is advisable to study the options for operating the device, its device, as well as the rating of TOP modifications.

    Show all

    What is a tankomizer?

    The mechanism for using electronic cigarettes is a vapor generator with a battery pack that supplies current to vaporize the liquid from the tank. The design nuances of the device are responsible for the taste and aromatic saturation of the steam.

    The principle of operation of a vape device is similar to an electric boiler. The scheme of the device includes a nichrome spiral with an internal quartz wick impregnated with a non-flammable liquid. After voltage is applied to the working element, the filament instantly glows and the liquid in the tank is heated. The resulting vapor is inhaled by electronic cigarette lovers.

    The development of the vaping industry involves the development various options"soaring". Mechanisms differ in design, method of use, functionality and price. Knowing all the features will allow you to choose the right product different types appliances.

    Varieties by type of service

    According to this criterion, there are three main types of vape flavor tank:

    1. 1. Serviced modifications. Such atomizers provide the possibility of mechanical replacement of the nichrome coil (the main heating element). Inside the design there are special fasteners and a winding regulator, depending on the user's preferences. Such a device is aimed at those who do not want to purchase new analogues. You can simply replace the required elements in the existing apparatus.
    2. 2. Maintenance-free atomizers are classified as disposable devices. They have a limited lifespan. If a malfunction occurs in the heating coil, it is not possible to repair or replace the part. Among these units, there are several varieties: models with replaceable cartridges, clearomizers with an enlarged liquid reservoir, tubular cartomizers.
    3. 3. Partially serviced options. It does not provide for a change of the spiral, it is possible to replace the evaporator completely with filters and heating elements. Steam supply and taste cannot be adjusted. The process of changing parts is as simple as possible, it is implemented by installing a new evaporator in place of the old device. This is convenient and does not require painstaking work to install the spiral in a special compartment.

    Classification by type of construction

    An important criterion for atomizers is their configuration.

    It defines the main qualities of the device. There are three groups.

    Classic tankomizer

    The body part includes an evaporator and a replaceable cartridge. Inside it is a wick impregnated with a non-combustible composition and a spiral. These elements are protected from contact with each other by a metal partition. The whole structure is filled with special foam, into which the edges of the wick go. With the accumulator the evaporator aggregates by means of a connector. It has a hole for air supply when tightening.

    The evaporation system is placed in a metal cylindrical tank. The classic tankomizer looks stylish and is simple in design. Among the shortcomings, the appearance of carbon deposits on the spiral, which is very difficult to remove, is noted. This worsens the taste parameters of the steam, and also contributes to the burnout of the heating element and filler.

    Catomizer

    In this cigarette draw configuration, the cartridge of the replaceable type and the evaporator are impregnated with the filler and are installed in the same cylindrical housing. Filling the liquid is carried out through the hole provided in the mouthpiece using a syringe. Most catomizers are disposable devices; in the event of failure of any element, the entire unit must be replaced.

    This design is inherent in the eighth generation of electronic cigarettes, such as PS Royal, Smokoff Slim, etc. The advantages of such vape models are good density and rich taste of vapor.

    Clearomizer

    The modification is mainly made of special plastic or glass. The role of the synthetic filler here is played by the wick, to which the working fluid is supplied. The advantage of the design lies in the transparency of the body part, which allows you to observe the level inside the tank, you can adjust the amount of liquid flowing through the wick to the heating element.

    Clearomizers in some modifications are of a serviced type. This is convenient in that you can easily purchase and replace a tank or other defective part. Modifications are repairable and use replaceable helical coils. The main disadvantage of this design is the high cost compared to analogues.

    Coil resistance degree

    Another parameter in which tankomizers differ is the resistance of the spiral. All devices are equipped with a nichrome heating element, the resistance of which may vary. In electronic cigarettes, this parameter determines the density, saturation and temperature of the vapor. The size of the heating filament and the number of turns affect the value of the parameters.

    1. 1. Standard - 2.1-2.6 Ohm. Steam has medium saturation and density.
    2. 2. Low indicator - below 2 ohms. Such devices generate a larger volume of steam, but they fail more often.
    3. 3. High resistance - over 3 ohms. These are the tastiest vape tanks, as they produce a powerful and rich cloud of vapor with a bright taste. The battery of such devices is more powerful and better than that of analogues.

    TOP 5 best vape models

    To determine the best tankomizer among the proposed abundance of modifications, there are several criteria, the main parameters include the duration and taste of the puff, which can be medium, cigarette and hookah. It is better to adjust the brightness of the taste and the saturation of the steam yourself, which is provided only on serviced models.

    If an electronic device is purchased to quit traditional smoking, you should pay attention to tanks with a cigarette puff. Below is a rating of the best modifications that have proven themselves among vapers on the positive side.

    Geek Vape Ammit RTA

    The fifth place in the TOP is taken by a tank with one spiral and 3D type airflow. The device has been produced since 2016, during this period it gained popularity among vapers. Pros: good saturation and taste of steam due to a powerful mechanism and three-dimensional blowing of the heating element. Holes for fixing the spiral are provided in the inner part of the structure, which makes it easy to replace the part even for a novice user.


    The kit is completed with an additional clamping fastener that provides a secure hold of the element. Fluid supply is controlled by adjusting the slots in the tank. Refueling is carried out through special slots closed with lids. The body part is made of stainless steel, the tank is glass and transparent, its diameter of 22 mm allows you to hold 3.5 ml of the working mixture.

    Billow v2

    A serviceable type medium-tightening is introduced by the manufacturer Ehpro. The model is equipped with a pair of spirals; when blowing, air is supplied from the holes located at the bottom of the base. Process adjustment is carried out using a rotary ring. The tank is placed a large number of liquids (up to 5 ml). The transparent glass body allows you to control the level of the mixture.

    The basis of the mechanism is equipped with three racks with trays for reliable mounting of the coils. The ends of the heating filaments are held in place by cross screws. Refueling is carried out through special sockets. To do this, the tankomizer is turned down, the base is dismantled, refilled, and then the base is carefully screwed into place.

    UD Goblin Mini V3 RTA

    The tank includes five main elements in the design: base, interchangeable deck, evaporation chamber, body and filling compartment. The device works with two or one spiral, the airflow is regulated by a rotary ring, there is a control mark for accounting for the liquid level in the tank. The glass flask has a volume of 2 ml with the possibility of mounting an additional analog up to 4 ml.

    Filling process:

    • unscrewing the cover;
    • pouring liquid into one of the provided holes;
    • installation of the topcap in its place.

    Among the advantages: functionality, compactness, ease of operation. Cons: high price, the need to purchase additional parts.

    Crius

    On the second stage of the TOP there is a serviced tankomizer Crius with blowing from below and from the side. Puff type - hookah. The set is completed with various additional elements, adjustment is made by means of rotary rings. Manufacturers equipped the device with a set of several spirals, Japanese cotton filler, and a glass tank body.


    The liquid supply is as convenient as possible, for this you just need to turn the body of the tank relative to the base. Diameter - 22 mm, capacity - 4.2 ml.

    Steam Crave Aromamizer RDTA

    The leader among tasty vape tanks has a capacity of up to 7ml with a diameter of 25mm. A convenient base with a pair of large racks is provided, which simplifies the installation of the heating element. The spiral is blown from the side, the feed is adjusted by a rotary ring.


    To fill the tank, it is necessary to shut off the liquid supply, turn the lid on top and fill in the liquid. The body part is made of special glass. Convenient filling, large tank, pleasant and bright taste and aroma of steam are the main advantages of this device.

Recently, vaping - smoking electronic cigarettes - is at the peak of popularity. Although, according to vapers, smoking is not quite the right term for this process, because in fact, only the inhalation of vapor, or “soaring”, occurs. It is logical that due to the increased interest in electronic cigarettes, the range of vaping accessories began to expand. Let's focus on the most important part of the steam generator - the atomizer, consider its structure, principle of operation and determine the best atomizers for electronic cigarettes.

Today, everyone who has ever tried electronic cigarettes knows more or less about atomizers. This is not surprising: it is this element that allows us to consider an electronic steam generator a cigarette. Of course, the battery pack, with the help of which current is supplied for the timely evaporation of liquid from the tank, is also of no small importance. However, it is the atomizer that can be called the "heart" of the electronic cigarette. Design features atomizers provide the main properties of a vape device: the density and volume of exhaled vapor, the richness of taste and aroma of the liquid filled into the device.

If you are new to the world of “vaping” and do not yet understand exactly how an atomizer functions, remember ordinary boiler. It is with this unpretentious device that our device can be compared. The very design of the atomizer is a nichrome spiral, inside of which there is a wick (quartz thread) impregnated with a non-flammable liquid. When voltage is applied to the coil from a source of electricity (battery), it instantly heats up and heats the wick very much. The liquid in the wick also reaches high temperatures and goes into a state of vapor. The resulting vapor is inhaled by vapers.

Accordingly, if the liquid is flavored, the vapor also becomes palatable.

Thus, in order for the atomizer to work correctly, the following components of the device are required:

  1. A battery that acts as a source of electricity.
  2. Refilled liquid (usually a replacement cartridge). It is she who wets the wick inside the spiral.

The smoker is inhaled through a special mouthpiece. With the help of connecting elements, a battery mod and an atomizer, or, as it is called, a tank, form a single electronic device with different characteristics.

Classification of atomizers

The vaping industry is constantly evolving, and manufacturers offer a ton of options for vapers. These devices vary in size, design features, coil resistance, maintenance. In order not to make a mistake in choosing an atom, it is best to know the main features of a particular type.

Service possible

The most common classification of vape devices is serviceability.

  1. serviced. These are atomizers, the manufacturer of which makes it possible to manually change the heating element - a nichrome spiral. As a rule, inside the design of such atomizers there are special fasteners for convenient installation of the coil. Some models also allow you to replace the wick yourself and customize the device to your taste (for example, adjust the winding of the spiral). This type of atomizer is suitable for those users who do not want to constantly buy new devices - it is easier to replace the necessary elements in an existing device. Perhaps, for beginners, a serviced atomizer will not seem like the most successful acquisition, but over time, having understood the range of accessories and understanding the principle of operation, they will opt for this particular type. Full service models are found among clearomizers, tankomizers, atomizer drips.
  2. Semi-serviced. In this case, it will not be possible to change the coil, but the manufacturer allows you to change the whole evaporator, that is, part of the atomizer with a coil and screwed wicks. In this case, there is no provision for changing the winding of the spiral, which means that it is impossible to adjust the taste and amount of steam generated. The replacement process is quite simple: it will be enough just to attach a new evaporator to replace the old one to the main base of the device. In general, it is even more convenient and takes much less time than painstaking manual installation of the coil into the compartment with fasteners. This type includes the following devices: clearomizers, Ego-C atomizers, DCT tanks.
  3. Unattended. These devices are considered disposable. They have a limited service life, because in the event of a malfunction, it will not be possible to change the heating element. After a breakdown, most likely, you will have to purchase a new model. However, disposable atomizers also have their own varieties: with replaceable cartridges (the most short-lived and inferior in taste to other types), more reliable cartomizers in the form of a tube and clearomizers with large capacity for liquid.

According to the degree of resistance of the spiral

As mentioned above, the devices are equipped with a nichrome spiral - the main heating element of the design. Electrical resistance may vary. Ohm's law, known since the school physics course, says that the greater the resistance, the less current is supplied. In our case, the resistance of the coil determines how thick and at what temperature the steam will be.. If the number is low, then the output is very hot and dense steam. The resistance value is affected by the size of the heating coil and the number of turns in it.

  1. Standard: The resistance is between 2.1 and 2.6 ohms. Steam is formed of medium density and saturation - this is the most acceptable option for vapers.
  2. Low resistance: no more than 2 ohms. These devices generate much more steam than standard models, however, as a result of intensive work, they often fail.
  3. high resistance: more than 3 ohms. Vaporization is powerful and rich, the taste of steam is usually bright. Such tanks are equipped with a more capacious and high-quality battery than the rest.

By type of construction

The third and rather important criterion by which atomizers are classified is the type of construction. In fact, it is the design of the device that determines its main qualities.


Top 5 e-cigarette tanks

How to determine the best atomizer among the abundance of proven devices and fresh news? There are several criteria for identifying the best atomizer, but mostly it is the taste and the duration of the puff. There are three types of puffs: hookah, medium and cigarette. If you are purchasing an electronic device for the purpose of quitting smoking, then we advise you to opt for tanks with a cigarette puff. The taste of steam is more dependent on the liquid that impregnates the synthetic winterizer. It is better to adjust the brightness of the taste yourself, which means that you should pay attention exclusively to serviced models. Having determined the main requirements for buying a high-quality atomizer, we offer you a small rating of the best models. All of them were released during 2016 and 2017, and in a short time they have proven themselves among experienced vapers only on the positive side.

5th place - Geek Vape Ammit RTA

On the fifth place of the top is a tank with one spiral and 3D airflow. This device was produced in 2016, and since its inception has gained popularity among vapers. The reason for this is the excellent taste of steam thanks to a powerful tank and a versatile, practically 3D blowing inner spiral. Air is supplied from two slots at the top and bottom, and air is also supplied from the side.

Inside the design there are large holes for attaching the coil, so it will not be difficult to replace it even for a novice vaper.

In the delivery set there is an additional fastening-clip for correct and secure installation heating element. The liquid supply can be controlled independently thanks to the slots in the tank. The Geek Vape Ammit RTA Tank is easy to refill, just remove the top cap and load e-liquid into one of the slots. The body is made of stainless steel, the tank itself is made of glass. The diameter is 22 mm, the volume of the tank is 3.5 ml.

4th place - Billow v2

This model is a novelty medium puff, serviceable atomizer from the manufacturer Ehpro. This modification means installation of two coils. There is a bottom blowing of the spiral, while the air comes from a pair of holes at the bottom of the base. You can adjust the airflow with a rotary ring. The liquid tank is characterized by a large capacity - the volume is 5 ml.

The body of the tank is made of glass, which means that you can control the level of liquid inside at any time.

The base of the atomizer is equipped with 3 racks with special slots for strong installation of coils. The ends of the helix are held in place by Phillips screws. Refilling this tankomizer is simple: you need to turn it over with the drip tip down and disconnect the base. Next, you will need to fill the liquid through one of the filling holes, and then carefully screw the base back. The disadvantage of Billow v2 compared to similar models is education a small amount pair- most likely, it will not work to create a huge cloud around you.

3rd place - UD Goblin Mini V3 RTA

This modification was developed by UD Technology. The tank consists of five main parts: the base of the device, a replaceable deck, a dome of the evaporation chamber with an air duct, a body and a top cap - a cover for filling. The tank can function with one or two coils thanks to deck replacement system, and there is a swivel airflow adjustment ring, which can be adjusted to your liking. On the ring, you can see a special engraving, indicating the degree of opening of the air supply hole. There is also a mark by which you can track the amount of liquid in the tank.

The volume of this atomizer is 2 ml of liquid, but you can additionally purchase replaceable tank up to 4 ml. The flask of the tank is glass, and the glass, if necessary, can be replaced with a new one.

All you need to properly fill the tank is to stop pouring liquid into the evaporator and unscrew the top cap. Then you just need to pour new fluid into the tank through one of the holes in the base. The obvious advantage of the UD Goblin Mini V3 RTA is its small size, functionality, ease of operation and excellent dense vapor. The disadvantage lies in the need acquire additional details , for example, a larger tank.

2nd place - Crius

In the second place of the top is the serviced Crius atomizer with bottom and side airflow. Puff - hookah, free. The first thing that catches your eye when you see the device - rich equipment and huge selection spare parts for the limitless imagination of vapers and complete control over the vaping process. There is a space in the atomizer box under the main upper compartment, in which the manufacturers placed a set of several coils, a piece of wire for self-winding the coil, and a piece of Japanese cotton filler. The manufacturer took care of a set of duplicate swivel rings and tank glasses.

In the tankomizer, convenient control of the liquid supply is carried out: you just need to carefully turn the body of the tank relative to the base. The diameter is 22 ml, the volume of the tank is 4.2 ml. The advantage of Crius is to get thick and voluminous steam in addition, the device is refueled without difficulty - just slide the tank cap and load the liquid into the opened hole.

1st place - Steam Crave Aromamizer RDTA

One of the best tanks of 2017 is the Aromamizer RDTA from Steam Crave. This vape device is equipped with capacious tank about 7 ml. In the latest model, the tank diameter is as much as 25 mm. There is a convenient base with two large posts to simplify the installation of the coil. The spiral is blown here from the side, and it is possible to adjust the air supply to your liking - there is a rotary ring for this.

To fill the tank, you will need to shut off the fluid supply, turn the top cap and pour fluid into the tank. Before unscrewing the tank cap, we recommend that you pay attention to the corresponding mark. The body of the tank is made of high-quality glass (there is also a spare in the delivery set). Thus, the main advantage of this model can be considered convenient refueling, an excellent capacious tank and a pleasant rich taste of the resulting steam.

Conclusion

We hope that our article has helped you better understand what atomizers are, how they work, and which models are considered leaders in the modern vaping industry. We have determined the best atomizer based on user feedback and device characteristics, but do not forget that manufacturers are constantly "upgrading" their developments and offering innovative devices. So, over time, the models will improve and delight vapers with new features and capabilities.