Porch 

Hanging dryer for drying fish. Do-it-yourself fish dryer: an overview of designs. How to dry and dry fish on a fire

Dad, well, how can you not understand, I don’t like oily fish, I like dry ...

The task is clear, the goal is set, the tool is ready - we will make a dryer for drying fish.

I must say right away that I only bought a mosquito net, in the "hostess" store - 55r running meter, took 2.5 meters - it was enough for me.

Everything else was in the country in the garage, in abundance

So, to start, I took:

4 bars of 120 cm each - the legs of the future dryer

6 bars of 60cm - crossbars

8 bars of 40cm each - the crossbars on which I will install the rods on which the fish will be hung.

From all this disgrace, I assembled the frame, this is what happened:

Very crooked but with a soul! It does not affect the meaning of the product in any way - therefore, I did not bother with precision accuracy.

I drilled holes in short crossbars, not through ones. I found rebar in the garage - I cut it with a grinder to the length I needed - and put it in the drilled holes - two rebars per tier.

The corners of the structure were fixed with corners

Corners with reinforcing bars inserted into the crossbars - gave the structure rigidity.

I decided that there would be few inserted fittings - the rest were sawn, I just grabbed them with self-tapping screws. The main thing is that a hand should pass between the armatures - it will be more convenient to hang the product.

We turn it over, wrap it with a mosquito - we grab the mosquito with carnations. The main thing here is that the mesh should be a little bit with a margin, and in one of the corners it went in two layers - otherwise the flies are such that they will seep into any crack

Bottom. I didn’t make the bottom of the mosquito, because the flies manage to place their offspring right on the net covered with smelling slurry (and from freshly hung fish, they will inevitably dig up the brine).

Therefore, I decided to make it from ceiling plastic.

I twisted the two pieces together, adjusted them exactly to size. Here accuracy is important - so that there are no gaps left - flies will not forgive lye

I put it in place, walked around the perimeter with screws.

Then he took the same corner

And fixed the grid along the side faces of the structure

The remnants of the grid on top - turned out.

I made the lid, like the bottom, from ceiling plastic

We cover, press down with bricks - the finished structure:

After assembly, I found a jamb. When you put your hand into the dryer, you can't reach the bottom, so when hanging the fish - if it fell to the bottom - there will be a little problem with catching it - keep this in mind.

Now take a bowl

we open it, and there, after a three-week salting

quickly cut hooks with knitting wire pliers

posting

But, just what I was talking about - crucian fell to the bottom.

you can’t get it with your hand - but there is a skewer - it’s easy for them

We put the dryer with fish in a ventilated, shady place, we are waiting for a week, another and delicious dried fish is ready to eat.

I don’t bite or hurt everyone. Thank you son for the challenge.

Dryers for fish of various variations, of course, are sold in the store. But to do something with your own hands is a pride for a real man, and even more so for a fisherman. It is possible to dry the catch without a special design, however, all the “old-fashioned” options (on clotheslines, on a balcony, attic) do not exclude the possibility of product contamination.

We make a dryer for fish on our own

First of all, you need to decide what kind of dryer you need, and what materials you have for its manufacture. The “insides” of the dryer are strings, hooks are not difficult to manufacture. They can be quickly built from:

  • wires;
  • clothesline;
  • strong threads twisted in several rows.

It is much more important to properly make the body of the dryer itself, which will prevent flies and wasps from getting inside.

From plastic boxes

For the manufacture of such a dryer, absolutely any plastic box, of any shape and size, will fit. Since this material does not allow air to pass through, this structure will need to be equipped with an exhaust hood. In addition, you will need:

  1. Corners (plastic or duralumin).
  2. Glue or liquid nails.
  3. Fasteners (bolts).

Of the tools enough:

  • jigsaw or clerical knife;
  • screwdriver.

The advantages of this design are that it is very easy both to operate and to assemble. In addition, it is easy to disassemble and wash.

From plastic panels and corners

The construction of such a dryer is similar in some respects to the installation of the model described above. The only difference is that in the first case we take a ready-made box, and in the second case we make it ourselves according to the dimensions we need.

For the design you will need:

  1. Plastic panels.
  2. Guides, corners, finishing strips.
  3. Liquid Nails.
  4. Wire for rods.
  5. Hood.
  6. Mesh for closing the inlet.

From wooden blocks

The simplest and most reliable is a fish dryer made of wood blocks. For its manufacture you will need:

  • bars;
  • self-tapping screws;
  • mosquito net or tulle.

Other options

List all possible options constructs make no sense. But to get you up to speed a little, let's just divide the dryers into categories:

  1. Framed and frameless.
  2. Foldable and one-piece construction.
  3. Mobile and stationary.

Practically any of them can be built with your own hands.

Dryer installation

Let us analyze in more detail the assembly of the dryer from a plastic box:


Assembling the dryer plastic panels and corners requires the following actions:

  • we measure the height of our box on the plastic panel and cut off as many planks as we need. It is not difficult to count them: divide the estimated width and height of the box by the dimensions of the panel and round this number;
  • in the same way, cut out the details for the bottom and lid of the box;
  • assembly of plastic panels is very simple: the first panel is fixed in the corner of the required length, all the rest are glued to it in the area of ​​the grooves with liquid nails;
  • as soon as the side is assembled, we fix the top with a finishing bar, and the bottom and the second edge with a corner;
  • in the same way we assemble two more sides of the box, and then - the panels of the bottom of the structure;
  • then we complete the assembly of the last side. Remember that there should be a finishing bar everywhere on top;
  • we also glue the details of the lid together and ennoble the edges with planks;
  • then everything is according to the scheme, as in the installation of the first dryer: hood, rods.

Assembling a dryer from wooden bars involves the following steps:


Any dryer for fish can be made at home. The main thing is the presence necessary materials and tools. When choosing a model, be guided by how it will be used: on the balcony, in the garage, in the open. It depends on whether the dryer has any additional designs: legs, hanging mounts, fan, etc.

In summer, fishermen in large numbers turn out to be the owners of a solid catch. The key task in this situation is the possibility of preserving the trophy for a long time. Drying the catch can become a solution to the problem, which will prevent product spoilage for the next 8-12 months. But for drying you need a specialized dryer. It can be either purchased at any specialized store or made with my own hands. For such purposes, a small amount is needed. various materials and tool.

What it is?

This is a specialized device for drying fish, which can be purchased at specialty stores. Dryers vary in capacity, appearance, options, design, cost. When purchasing the installation, it is necessary to take into account that there are a number of modifications of both domestic and foreign manufacturers.

Kinds

The simplest device for drying is considered to be a wire stretched under an awning or an ordinary rope for drying clothes. To protect against flies, a net (or gauze cloth) is simply hung on the fish. Hanging a roach, crucians or bream is allowed both on hooks made of wire, from ordinary paper clips, and clamped with clothespins. This method stands out for its simplicity, but it is optimal for a one-time harvesting of fish in a suburban area or on a hike. When the occupation is put on the “conveyor line”, and good catches are constant, it is necessary to think about a relatively decent design.

Devices for drying fish can be symbolically divided into two large groups:

  • mobile transportable (portable);
  • stationary.

Each of these samples has its own advantages. The first can be used anywhere: from the river bank to the loggia in the apartment. Others can be listed as drying cabinets, in most cases they are used not only for fish, but also for drying berries, herbs, vegetables, withering meat and other food purposes. You can simply dry the fish in the open air, or you can organize it with the forced injection of air masses by means of a fan. At the same time, the withering procedure is much faster, and the product is prepared more proportionally. AT cold period the drying cabinet can be equipped with electric heaters, which, in turn, will also allow you to quickly prepare the fish for consumption.

characteristic feature drying chambers is also the number of compartments. As a rule, single-section types are used, but there are dryers with a considerable number of departments, in some modifications their number reaches up to 5 compartments. Let's consider some models in more detail.

factory models

From factory modifications, 2 options can be distinguished. The first one is structurally implemented in the form of a tall cabinet made of steel tubes covered with mesh. Similar samples are produced various firms under trademarks"Kedr" and "Mitek". Another interesting example is the two-level IdeaFisher ECO-2. This collapsible design is also small in size and can be easily carried. Moreover, based on the conditions, it functions both suspended and placed on the floor or table.

Homemade dryers

From the mass of devices for drying fish follows note the following homemade designs:

  • frame;
  • folding;
  • stationary;
  • suspended;
  • electric dryer;
  • with fan;
  • mobile (portable).

But this is not all that homegrown masters are capable of.

First of all, it is necessary to clarify where exactly the drying will be carried out. If under a canopy, awning or in the attic individual home- there are no problems with dimensions. If in one of the living rooms, on the loggia or balcony high-rise building, then the parameters of future equipment for the dryer must be planned, starting from the possibility of placing it in these premises for drying and further maintenance. In addition, it is necessary to take into account the dimensions and the number of fish caught on past fishing trips. Or balance these conditions for future catches. If the area is very small, it is necessary to analyze the modifications of folding and hanging dryers.

After establishing the desired dimensions, it is required to decide on the choice of materials of manufacture.

materials

It is necessary that steel or wooden materials. Thus, it will be possible to practice it for more than one year. The frame must be stable. In order for the device to be of high quality, it must be fixed with durable components (screws). On top, the base is covered with a thin material (chiffon) so that the fish dries on fresh air. Due to the free movement of air inside the structure, the product will dry much faster.

How to choose?

Having studied all the modifications of the dryers, the vast majority of anglers trust the time-tested hanging samples, which are made of a metal frame and nylon mesh. The key advantages of such a material are the strength of the structure during drying, the protection of fish from unnecessary contact with flies, experience gained over decades. The structure contains many levels, thereby guaranteeing a hit clean air for the production of high quality and non-hazardous food products. To dry the fish after fishing, you can use hanging samples from various companies.

  • "Three whales". This is a well-known domestic manufacturer that carries out mass production and sale of everything you need for hunting and fishing.

  • "Cedar". In order to make life easier for anglers, Kedr has additionally created a camping version of the net for drying fish. Its structure is strong and durable, it makes it possible to dry fish on a long trip or in a summer cottage.

  • Electric dryer for fish. All of the above modifications have manual control, in other words, the desired effect depends solely on the human factor. In fact, such a device can be recreated at home, using several gauze shells, wood (steel) crossbars. Fish need not only be caught, but also hung, along with this, constant monitoring is a natural process of drying it. In order to speed up the final result, it is advisable to use the most advanced modifications - electric dryers. These innovative installations are much more expensive, but in the shortest possible time they allow you to enjoy the memorable taste of dried fish.

How to do?

So we got to the most interesting. Let's talk about how a do-it-yourself fish dryer will be built. It should be immediately noted that there are a huge number of dehydrator devices. It is very difficult to tell about all the varieties of improvised structures within the framework of one article, since the imagination of the domestic Kulibins is indeed inexhaustible. Information! Dehydrator in literal translation from Latin means "dehydrator", in other words, the same thing as a dryer.

Wireframe models

In most cases homemade devices made in the form of a wooden box covered with a mosquito net. And one of the most common is considered a variation with dimensions of 500x500x500 millimeters. At the initial stage of manufacturing, it is necessary to prepare the required amount of wooden blocks, process them with sandpaper and cover with a protective solution. The coating must protect the device from dampness and salt, but at the same time not emit negative fumes that drying products can absorb.

After that, according to a previously made drawing, the skeleton of the future dryer is assembled. Self-tapping screws and iron corners are used for mounting. To create such a box, you need to follow a series of steps.

  • Mark the timber, then cut it with a jigsaw or hand saw.
  • After that, using a screwdriver, corners and self-tapping screws, mount the frame.
  • Rigidity partitions are placed on all sides.
  • A cable is fixed on the side walls (in fact, the fish is dried on it).
  • Next, you need to process the box with an insect repellent.

  • It must soak the material and dry, and only then the box can be varnished. It is absolutely necessary to apply it in 2 layers with a time interval of 4 hours.
  • On the bottom of the box, it is necessary to install specialized spacing.
  • The door frame must be sealed. Having done this work, you will have a ready-made box for drying fish, where no insects will be able to get through.
  • Recommendation! The static dryer can be installed directly on the wall.
  • After the base is ready, they take up the tension of the mesh. Along with this, it is necessary to clarify how access will be made inside. To do this, make a door or sew a zipper.

Another option for a similar homemade product is the use of not a stretch mesh as a drapery, but devices from modern PVC windows. In this option, it is not required to make a separate door, but to use a frame from a finished counter mosquito net.

Dryer with fan

Some of the models of dryers made by Russian craftsmen have fans in their own structure. Air heat exchange in such dehydrators makes it possible to force the drying process. They create such devices from a variety of plastic containers or something like closed cabinets through which an air stream is driven. Let's analyze the production process of a simple device with a fan. For this purpose we will need:

  • large plastic tank - from 20 liters and more;
  • fortochny exhaust fan;
  • ventilation grate;
  • threaded steel rods with matching nuts;
  • fasteners for grille and fan.

We work in the following order:

  • in the lid of the tank we make a hole for the ventilation grill and fix it;
  • we fix the fan in a similar way in any of the side ends of the plastic box;
  • in the upper segment of the tank we create holes for the rods and insert them, fixing them with nuts (we will hang fish and meat in this place).

If you want to increase the ambient temperature in such a dryer, you can use electric rugs. Such products are sold in pet stores for breeding reptiles.

Are you used to making a ram the old fashioned way? There is a proven modern way to secure the product. A fish dryer is an opportunity to facilitate the process. You need to dry the catch in the fresh air, but away from the sun. Optimal solution- a shadow that can not always be provided in nature. You can also buy a fish dryer for home use. A strong yet lightweight design will protect your catch from insects and other pests.

Product Features

The design for drying is a fishing equipment that is indispensable both for camping and at home. The compact device is stable and has increased durability. With it, the process of obtaining dried or dried fish will become simple and understandable. There are several types of such equipment. Hanging dryer for fish can be used while fishing. It is enough to hang it on a tree or fix it above the ground with a tripod. Models on a stable metal frame can be installed anywhere. They are suitable for large volume production.

Advantages:

  • Price. The device costs from 500 rubles. The price depends on the capacity, type and materials used.
  • Strength. Made from lightweight yet durable materials. The walls and crossbars are made of ventilated mesh. It is based on a metal frame, which is difficult to deform. Some models are equipped with sidewalls and a roof made of tear-resistant, waterproof fabric.
  • Versatility. You can dry fish, fruits and berries, herbs. Ideal for any product.
  • Simple application. It is enough to hang above the ground or install on the frame. Easy to store out of use. When folded, it takes up minimal space.

Where can I buy

Need a fish dryer in Moscow? Offers to buy it

Delicious, dried fish is the best addition to beer on a nice pleasant evening with friends. To save money and not buy from the store dried fish, You can make it yourself. How? Very simple and inexpensive, you just need to make a little effort.

How to make a box for drying fish with your own hands?


To make a box, we need some materials, as well as some skills to work with tools.

We will need:

Wooden bars;

Mosquito net;

stapler;

Screws for wood.

1. First of all, we determine the size of our future box. We chose the size: 1 meter high, 1 meter long and 0.5 meters wide.

2. We cut the bars of the size we need and sew them together with screws.

3. To make the box more stable, we will strengthen it with several ribs.

4. We hook the cables between the side ribs. They immediately perform two functions: they do not allow the frame to stretch, and we will hang fish on them.

5. Let's start processing wood. We open in two layers with Bio-doctor from beetles.

6. After the wood dries, we proceed to the opening with varnish. It should be opened in two layers, with an interval of 5 hours.

7. After the varnish dries, we will cover it with a mosquito net using a stapler. We sheathe almost from all sides, we do not sheathe the front one, there we will have doors.

8. We do the doors in the same way with the help of bars, mosquito nets, and we hook them on the hinges. They should close the box well.