Gate and fence 

Types of glass and options for replacing it, tips on how to disassemble and install in an interior door. Instructions for replacing glass in an interior door How to replace glass in an interior door

In this article, you will learn how to replace glass in interior door with your own hands. And we will also describe in which cases it is better not to do this yourself without experienced specialists.

Glazed doors are an adornment of any interior. In addition to being attractive appearance the glass in the door also has a practical function: it visually expands the size of the room and lets in additional light.

Due to their fragility, glass door elements often break or crack. If you decide to change the broken glass in the door leaf with your own hands, then you must first find out the degree of complexity of the work ahead.

Replacing glass in interior doors leaves you with two options: contact the masters or make the replacement yourself. With the first method, everything is clear: they found a phone number, called, the master arrived and did everything. You were satisfied, but paid money (sometimes a lot).

So, what is the plan for replacing glass in an interior door with your own hands:

  1. We take out the remains of the broken glass from the door.
  2. We make measurements for a new glass element.
  3. We order or buy new glass.
  4. We prepare the door leaf for inserting new glass.
  5. We insert and fix the glass in the interior door.

And now we will analyze all these points in detail.

The answer is unequivocal - carefully!

For this procedure, you will need the following tools and tools:

  • Tight, but not too thick gloves.
  • Chisel or wide slotted screwdriver.
  • Little mallet.
  • Thick paper.
  • Broom and shovel.

We put on gloves and with the help of a hammer and a chisel (screwdriver) we loosen the fasteners - glazing beads. We don't take them out until the end.

Important! In order to safely remove the remnants of broken glass from the door, the glazing beads must first be loosened from the top.

Now carefully remove the glass fragments. You should start with the largest ones. After removing them, immediately put them in prepared paper and wrap them. Now you can remove the fasteners.

If there is a rubberized gasket into which the glass is inserted, inspect it carefully. It may be damaged. In this case, you may need to purchase a new gasket tape.

If some parts of the glass fell to the floor and broke, then we collect them with a broom in a scoop. Try not to leave a single piece on the floor. All work is best done in slippers with hard soles or other shoes.

We measure the opening for new glass

There are also two options here: call a glazier or take measurements yourself. If the broken glass had a complex shape, then it is better to use the first option.

Moreover, it is better to call the master from the workshop, in which this glass will be cut out immediately. With the correct and uncomplicated glass shapes, you will be able to independently remove the desired dimensions.

You can buy glass in hardware stores or special workshops where they cut products. Modern manufacturers offer a wide range of products with different relief patterns, levels of transparency, shade or resistance to damage. If children live in the house, then it is important to purchase glass for an interior door with high impact resistance.

The peculiarity of calculating the parameters of the insert object is to measure the doorway. To this indicator, you will need to add a few millimeters of depth to insert the product. All measurements are best done using a ruler to determine the exact bed distance. Otherwise, the dimensions will be inaccurate, making installation impossible.

Important! Glass should never fit snugly into its box! That is, its dimensions should be less than the bed by 1.5-2 mm on each side.

Acquisition of new glass for interior doors

Order or buy new door glass can be in specialized workshops for cutting glass and mirror products. Or you can go to the building supermarket where the door was bought and make a purchase (order) there.

Interior door leafs with glass inserts of various shapes and sizes are a popular interior design option today. Sometimes the question may arise about how to replace the glass in the interior door with your own hands if it is damaged. This nuance must be taken seriously and carefully studied the replacement procedure, otherwise the design will not have an attractive and aesthetic appearance.

The design and name of the elements of interior doors

It will not be difficult to insert new glass into the opening if you prepare the necessary tools and materials for the mission and follow the step-by-step instructions.

To do-it-yourself replacement of glass in the door structure, you should stock up the right tools and materials. These include:

This is the minimum set of tools and materials that should be on hand at the time of self-replacement of glass in interior doors.

Glass types

Today in the construction market there is not a single option for replacing glass in doorways. Before deciding on your own to change the damaged glass in the door structure, you need to study some types of materials and bet on the one that best suits your wishes. You can pay attention to such glass for doors:

In fact, each of the above types of glass is suitable for installation in interior doors. But it is worth familiarizing yourself with the features of each of them and betting on the one that is most suitable in all respects.

Ordinary glass

Benefits include the following:

  1. The cost of such glass is available to everyone.
  2. Installation does not require additional knowledge and equipment to cut the desired part.

Of the shortcomings, only one can be named, ordinary glass requires additional finishing after installation, which means the purchase of additional materials.

Sliding door design with glass

Such glass is pasted over with a decorative film, which can be ordered or picked up in a store along with the base material.

In general, if you prepare all the necessary raw materials, then this option is quite worthy of attention.

decorative glass

This type of material for work has such a number of advantages:

  • exquisite design solutions, among which everyone will find an option for themselves;
  • just as easy to install as with conventional glass.

Among the shortcomings, the following facts can be noted:


Turning a blind eye to the shortcomings, this version of glass for an interior door is worthy of attention.

Organic glass

The advantages are:

  • this type of insert in the interior door has high strength;
  • the cost of the material is average between ordinary glass and decorative.

Disadvantages:

Glass door designs

Having thought over what pricing policy is suitable, and what skills you have for installing glass in an interior door, you can bet on a certain option. After the acquisition, you can begin the process of installing new glass instead of the damaged one.

Preparing to replace glass

Step-by-step instruction:


Features of parsing doors

When replacing glass in a door, remove the door from its hinges.

The process of removing doors from hinges

This will help ensure safety during the procedure. Lay the structure on a flat surface so that it is convenient to carry out the work. And the surface, in turn, should be covered with a dense material that will protect flooring from damage. The door structure will have to be disassembled in any case. And this stage of work should be approached with caution and responsibility. Before proceeding with self-replacement of glass, you need to measure the size of the glass.


The complexity of the process depends on how non-standard the shape of the glass is. When the stage of disassembling the doors and removing the old damaged glass has come to an end, you can proceed to further steps.

Preparing a place for glass

When top part the door structure is removed, it is necessary to prepare a place in which the glass will be placed. Before replacing glass in an interior door, you need to:


These actions will improve the quality of work on replacing damaged glass in the door leaf with a new one.

Glass installation

When the canvas is ready, glass replacement can be started with confidence. The main task is quite simple to carry out.

The main thing is to perform the procedure in the right order and use high-quality related materials.

The sequence of actions is as follows:

  1. Application of silicone (sealant) at all attachment points. The easiest way is to correctly around the entire perimeter, it will turn out to carry out the procedure with a construction gun, which will accurately distribute the sealant over the surface.

  2. Then you need to take a piece of glass pre-fitted to size and pull a protective gasket over it.
  3. After that, the glass is mounted in the structure of the prepared door frame. Glass is the most fragile material among all that are used in the process of replacing a damaged structure. Therefore, you should not make an effort if the glass does not fit well into the grooves of the door. It will be better to cut the gasket or the glass itself, fitting it to the desired size.
  4. When the glass is inserted into the opening, it is required to apply silicone (sealant) again with a construction gun on the other side.
  5. After you need to fix the upper part of the door structure with the help of glazing beads. When dealing with glazing beads, you should act carefully, they should fit snugly against each other.
  6. Glazing beads are fixed by fastening them over decorative nails, which will give an aesthetic appearance to the structure and make the overall picture of the interior doors of the apartment look like new.
  7. When the carnations are fixed, you should wait a few hours for the silicone to grab well and not become, then the cause bad work door handles or did not spoil the appearance of the structure with streaks. Indeed, in this case it will be difficult to change something, you will have to start work on replacing the glass again or completely replace the door structure.
  8. After a few hours, you can begin the process of installing the doors in their original place. It is necessary to pre-lubricate the moving structural elements, then fix the door in the opening.

    The process of installing the door on hinges

Watch the video: replacing broken glass on an interior door.


Replacing damaged glass with your own hands is easy. The main thing is to responsibly approach the process of choosing materials and the installation of glass in the opening of the door structure.

To do-it-yourself replacement of glass in the door structure, you should stock up on suitable tools and mi. These include:

  • gloves to protect hands from cuts and abrasions;
  • also, in order to replace broken glass, a chisel may come in handy;
  • when inserting the latest glass, you will need a hammer, you can use both carpentry and special furniture;

    Design option for an interior door with glass

  • sealing paper should also be at hand, it will be needed to adjust the size of the glass and its strong fastening in the door structure;
  • silicone is also useful for strong fixation, regardless of whether ordinary glass is installed or decorative;
  • it is also worth having a broom and a dustpan on hand to sweep away excess chips and glass residues from the door frame.

This is a small set of tools that should be at hand at the time of self-replacement of glass in interior doors.

Back to index

Glass types

Today in the construction market there is not a single option for replacing glass in doorways.

Before you dare to change the damaged glass in the door structure on your own, you need to study some types in and bet on one that is very much in line with your wishes. You can pay attention to such glass for doors:

  1. Ordinary glass.
  2. Decorative glass.
  3. Glass organic.

In essence, each of the above types of glass is suitable for installation in interior doors.

But it is worth familiarizing yourself with the features of each of them and betting on the one that is more suitable in all respects.

Ordinary glass

Among the advantages, the following facts can be noted:

  1. The cost of such glass is available to everyone.
  2. Installation does not require additional knowledge and equipment to cut off a suitable part.

Of the shortcomings, only one can be named, ordinary glass asks after installing an additional finish, which means that additional purchases are made.

Sliding door design with glass

Such glass is pasted over with a decorative film, which can be ordered or picked up in the market, along with the main m.

In general, if you prepare all the necessary raw materials, then this option is completely worthy of attention.

decorative glass

This type of work has a number of advantages:

  • exquisite design solutions, among which everyone will find an option for themselves;
  • the same simple installation as in the version with ordinary glasses.

Among the shortcomings, the following facts can be noted:

  1. High cost per unit.
  2. Difficulty finding replacements if necessary.
  3. It is necessary to customize the sketch if we are talking about decorative glass with patterns.

Closing your eyes to the shortcomings, this version of glass for an interior door is worthy of attention.

Organic glass

The advantages are:

  • this type of insert in the interior door has the highest strength;
  • the cost is average between ordinary glass and decorative.

Disadvantages:

  1. Organic glass is a transparent plastic construction.

    Doors with organic glass

  2. Plastic, more than glass, is subject to corrosion and mechanical damage. Therefore, over time, organic glass loses its aesthetics and becomes cloudy.

    To avoid such misunderstandings, the surface should be treated in time with special protective mixtures.

Glass door designs

Having thought over what pricing policy is approaching, and what abilities for installing glass in an interior door are available, you can bet on a certain option. After the acquisition, you can begin the process of installing the newest glass instead of the damaged one.

Back to index

Preparing for glass replacement

Step-by-step instruction:

  1. The first thing to do is, using a chisel and a hammer, loosen the glazing beads that hold the fastener that holds the glass.
  2. It is necessary to start the work process from top to bottom, this is a safer option.
  3. When all the glazing beads are loosened, you can evenly begin to pull them out of the structure. This function also needs to be done, from top to bottom.
  4. It is carefully necessary to remove the upper structure of the doors and evenly, slowly, pull out pieces of warped glass. Be sure to wear protective gloves when doing this.

    Removal of the remaining glass from the door

  5. When the warped elements are removed from the base of the door structure, you need to sweep up the remains of the glass to make workplace safe.

Back to index

Features of parsing doors

When replacing the glass in the door, remove the door from the hinges.

The process of removing doors from hinges

This will help ensure safety during the procedure.

Put the structure on a flat surface so that it is comfortable to do the work. And the surface, in turn, should be covered with dense m, which will protect the flooring from damage. The door structure will have to be disassembled in any case. And this step of work should be approached with caution and responsibility. Before proceeding with the independent replacement of glass, it is necessary to measure the size of the glass.

The complexity of the process depends on how unusual the shape of the glass is. When the step of parsing the doors and removing the old damaged glass has come to an end, you can proceed to the upcoming steps.

Back to index

Preparing a place for glass

When the upper part of the door structure is removed, you need to prepare a place in which the glass will be located.

Before replacing glass in an interior door, you need to:

  1. Remove the lining that was previously used to replace it with a fresh one, or insert it back after surface preparation.
  2. It is necessary to remove the remnants of the consistency of the sealant or grease. When new glass is installed in the skylight, fresh mixtures must be applied for a high quality and durable construction.

    Removing sealant from the door

  3. The next step is to clean the surface with a small sandpaper. This will clear the glass clearance from protruding remnants of an old consistency and dust.

These actions will improve the quality of work on replacing damaged glass in the door leaf with a new one.

Back to index

Combined doors with glass elements look great and refresh the interior with their appearance.

But extremely often glass elements turn out to be of poor quality, crack, become covered with scratches and scuffs, or completely break into pieces. Do not despair if such a problem happened to one of your doors, because replacing the glass is not so difficult, especially if you turn to professionals for help.

In fairness, it should be noted that the most pleasant fact can serve as a prerequisite for glass replacement: for example, you decide to change the concept of interior design, but at the same time want to abandon the existing interior doors, in this case it is quite easy to insert the rest of the glass into them.

Glass replacement consists of the following steps:

  • dismantling of old glass;
  • taking measurements;
  • preparation in the glass workshop of suitable parameters;
  • processing of cut glass, its grinding, hardening in order to increase strength (if necessary);
  • installation of the latest prepared glass.

The cost of work is formed based on the configuration and dimensions of the glass sheet, its type, and also from which the door itself is made.

final cost finished work, you can calculate by referring to online consultant on our website or by calling a measurer.

Calculation of the cost of glass products according to your size

Glass replacement in interior doors

Modern interior doors can have unique design and, as a result, a complex structure.

In this case, you should not even think about replacing the broken glass sheet without the help of others. In some door structures, such an operation can only be carried out at a special enterprise.

How to insert rectangular glass

Replace broken glass sheet rectangular shape in the interior doors of the economy class, you can do it yourself.

Usually the glass sheet in such door structures is installed through the top.

Repair actions include the following steps:

  1. fragments are carefully removed from the door;
  2. the place where the glass sheet must be installed is measured;
  3. in the workshop, glass is ordered, of the appropriate dimensions and suitable thickness;
  4. the finished glass is carefully inserted on top of the interior door;
  5. for strengthening, silicone gel is used, which is applied around the perimeter of the glass;
  6. when the gel dries, it is necessary to remove smudges.

When measuring the place in which a new glass sheet will stand, it is imperative to measure the depth of the groove.

This value must be added to the acquired dimensions. The depth of the groove is set by lowering an iron ruler into it.

If the glass sheet is fastened with a "glazing bead", then measurements and installation are carried out in the same way. Only the "glazing bead" is previously removed from the door structure. At the end repair work it should be attached to its original place. Fastening is done with small carnations.

Repair of business class interior doors

Replacing the glass sheet in interior doors of this type is a rather labor-intensive process.

As a rule, these doors have a collapsible design. And in order to remove from them the warped glass part, the door structure needs to be completely disassembled, replace the glass, and later assemble it again. Such work can only be done by a specialist. Traditionally, it is created in a special workshop.

If we are talking about repairing a door structure from another, for example, aluminum, then there are difficulties here. If the glass sheet is inserted into the duralumin door in the same way as in the economy class door, and fastened in the manner of a “glazing bead” with an duralumin bar, then the replacement can be made.

But, direct contact of the alloy with the glass surface is undesirable. Therefore, when installing, it is worth using a rubber gasket. If the glass sheet is built into the door structure, then it can be replaced only in a special service company.

Replacement of unusual glasses

Glass sheets in interior door structures, made in a modern design style, may take different forms. It's great if they are oval, worse when the glass is made in the shape of a wave.

However, if the replacement of the glass sheet is done through the top, then you can try to do this:

  1. carefully remove the fragments;
  2. collect them on a large sheet of paper, putting each in its place;
  3. circle the glass around the contour with a marker;
  4. now you can order a glass sheet and insert it into the door structure.

Glass for interior doors

Glasses can be different in shape and production technology.

These reasons affect the price.

According to the technology of glass production there are:

  • colored;
  • transparent;
  • bronze;
  • transparent with facet;
  • satin with facet;
  • with fusing;
  • corrugated.

Prices for glass sheets may be different.

  • If we are talking about transparent glass, then its approximate cost can be from 1000 rubles. for 1 sq. m.
  • Matte can cost from 1600 rubles. for 1 sq. m.
  • The price of a glass sheet with a matte sandblasted pattern starts from 2800 rubles. for 1 sq. m.
  • Corrugated can be purchased at a cost of 2500 rubles.

    for 1 sq. m.

  • Stained glass can be purchased at a cost of 8000 rubles. for 1 sq. m.

Fixing glass with glazing beads

Very often, glass in interior doors is installed with the help of glazing beads, which are attached to ordinary decorative nails. In this case, the work of replacing the glass in the doors will be ordinary and swift, which you can handle on your own.

To get the glass, you need to carefully pull out the nails, take away the glazing beads and, voila, the glass is in your hands. We insert a new one into the vacated gap and return the glazing beads to their place. So that at the moment of opening or closing the doors, the inserted glass does not rattle, apply transparent silicone to the glass clearance.

Replacing glass in veneered doors

If you got a veneered door Russian production, and the economy class door itself, you can breathe a sigh of relief, the door glass is simply inserted from above.

We take it out, measure the clearance, order a new beautiful glass and carefully insert it. As soon as the glass is inserted, it is imperative to coat the gap between the glass and its lining with silicone. This will prevent the glass in the doors from rattling when you use them. If smudges come out - it doesn’t matter, they are simply removed with a clean rag.

Replacing glass in collapsible doors

Most often collapsible doors belong to business class doors. To replace the glass, you will have to disassemble the door itself. On the sides door leaf We find the bolts under the rivets and unscrew them. Traditionally, the bolts are at the top and bottom.

Before this, first remove the door from the hinges, since if the glass is not one, then others can simply get enough sleep.

The main difficulty for you will be to assemble back the elements of the door structure. Be careful not to get twisted.

Otherwise, the door will finish closing normally.

How to replace glass if it is the wrong shape

If you already have some experience in installing glass, then when the glass zigzags or is generally oval, the main difficulty in replacing is to guess the size.

It happens that the glass just cracks and remains in the doorway. In this case, before you get it for you, you must definitely take the dimensions that are redrawn using paper or cardboard.

In this case, the glass layout must be clear. Otherwise, you will have to order it more than once. Consider also the size of the groove, which along the perimeter of the glass opening should be the 1st size. Traditionally, this is 5 millimeters.

Selection

Replacing glass in interior doors can be justified different reasons, most often it is:

  • Damage. During the operation of the door, the glass insert can be easily destroyed. This is especially true for those who have active kids at home.

    But, it's not just about breaking ability. It can also be scratched or stained. If the problem cannot be eliminated in another way, the only way out is to replace it.

  • Obsolescence. Over time, old glasses lose their pretty look and may not fit into modern interior. If you do not want to completely change the door, you can limit yourself to changing the insert.
  • Update. This option is relevant for those who want to change the situation without significant costs. It's about not only about repairs, but also about a simple desire to correct the interior.

How to replace unnecessary glass in the door?

You can find, suitable in size, the remains of glass at home. Ordinary glasses can be decorated on their own with the help of a film or painting. Purchased options are the safest. Also, embossed ones are often used.

In addition to glass, you can use plastic or plywood sheets, the outer ones are decorated with any means available to you.

Fastening with glazing beads

To begin with, let's see how to change the glass in the panel interior door.

In this case, the insert is attached with glazing beads. In order to remove the old one, they must be carefully pry off and removed together with the carnations. After that, clean off the putty around the perimeter and carefully remove the insert. A fresh fragment is installed in its place, smeared with sealant and pressed with glazing beads.

Schematic representation of the fastening of glass in the door with glazing beads

Now let's look at how to insert glass into the door if you want to increase the area of ​​\u200b\u200bthe decorative element.

First you need to remove all the old parts. Using a jigsaw, cut out the required size hole. Wooden plugs are installed in hollow canvases around the perimeter. In them, you need to select the grooves with a drill, chisel or milling cutter. Next, glass of suitable dimensions is cut out and installed in the manner already described.

Demountable panel construction

In a slightly different way, you can insert glass into a paneled interior door. The highlight of such a canvas is that it consists of many collapsible parts.

Glass in this case - this is the panels. In order to replace them, it is necessary to disassemble the door in detail.

The paneled canvas has the following elements:

  • longitudinal (vertical) support is made of solid wood;
  • the transverse (horizontal) support is also made of wood;
  • panel, that is, the narrowest insert in the free space between the supports;
  • baguette element - decorates the inner perimeter of the insert.

Schematic representation of the construction of a folding panel door

The principle of connection is based on the tongue-and-groove joint.

It is not necessary to remove all parts, the main thing is to open access to the glasses. To do this, it is enough to remove the upper crossbar and slightly push the racks. After the inserts are removed from the structure, fresh ones are cut out according to their shape and size and installed in the same place.

Self-replacement of glass in the interior door

The glass door between the rooms looks extremely advantageous in any interior. But, in addition to beauty, it also performs practical functions. Due to the glass, the size of the room visually expands, and additional light passes into the room. It often happens that you need to replace the glass in the interior door. The reasons for this may be different.

The most common is its damage, the need for a turn, or the desire of the owners to replace the glass with one suitable for a brand new interior design.

The design of the interior door with glass.

How to replace glass in an interior door?

If there are no mirrors, colored stained-glass windows, glass baguettes and other decorations in the interior door, then you can, observing painstaking accuracy and the usual action plan, replace the glass yourself.

To determine the procedure, first you need to find out what kind of interior door you have. That is, it is necessary to realize how glass is attached to it.

In almost all old and almost all modern models glass doors can be inserted into the gap and fixed with ordinary or curly glazing beads. But there is another type of fastening (with a hidden fixation), when it is useful to bring the glass through the end of the door.

When replacing broken glass in an interior door, you must act very carefully so that when working with tools, do not destroy the door, as well as new glass.

Before starting work, it is useful to get rid of old glass, often broken or cracked. Better prepare yourself for this necessary tools and improvised means:

  • gloves (it is better to take tight ones, but not extremely thick ones);
  • medium-sized hammer;
  • scoop, broom;
  • paper of the highest density;
  • wide slotted screwdriver or chisel.

Fasteners in the form of glazing beads are loosened with a screwdriver (you can also take a chisel), a hammer.

Basically, wear gloves. It is not necessary to remove the fasteners one hundred percent. To be safe, it's best to start at the top. Gradually remove the fragments or glass, start with large ones. Put them in thick paper and immediately wrap them up. After that, the fasteners are removed. If the rubberized gasket is suddenly damaged, it is better to purchase a fresh tape. Make sure that nothing falls off or breaks, and if it does happen, then immediately remove the fragments with a broom and a dustpan. Work better in shoes.

How to replace glass: work steps

To change the glass in the interior door, it is useful to find its clearance.

With a complex shape, it is better to contact the glazier. Although at home you can make a special cardboard pattern. Apply the dimensions you purchased there. Now you can cut a new glass on it. Precise shapes can be handled without outside help. The main thing to remember is that the glass cannot go right into its bed. This means that it is necessary to write down dimensions that will be 1.5-2 mm smaller than the bed for each side.

Fragments of glass must be removed with thick gloves, at first large, then small.

Glass can be purchased either at construction stores, or ordered from a workshop that practices cutting glass and mirrors.

The interior door must be prepared for insertion.


From the entire surface of the bed, remove the old gasket, remove the putty that has served its own time, along with the sealant. Purchase fresh sealant (special for glass and windows) in advance. Glass fixing systems, which depend on the door model, may also come in handy. It may also happen that the glazing bead breaks during dismantling. On sale there is a large selection of flexible analogues of such fasteners, made in different colors.

Glass also needs to be prepared. Let it warm up room temperature. Then wash it using soap and water. Wipe clean with a clean cotton cloth. So cutting will go easier, while you protect the glass from breaking and crumbs.

Where the place of fastening, remove the remnants of paint and putty.

Remove your door from its hinges and lay it on some horizontal line. A table will do for this. The main thing is that it should be long and wide. So the interior door will be able to lie down completely, therefore, inserting glass in a suspended state is a risky business.

Apply silicone around the entire perimeter of the bed where the glass will lie. Use a caulk gun for this. Place the glass in the gasket tape. After that, start carefully putting it in the door. Eliminate pressure on its surface. If the insert is tight, try notching the gasket.

Process with silicone sealant and the second piece of glass.

Fastening glazing beads also sit on the sealant, after which they must be tightly fitted to each other.

And later it is better to fix them also to the door leaf. For this purpose for us, take decorative finishing carnations. The sealant sets for about an hour, no less. After that, you can hang the door back.

Each door will have its own aspects. But with the desire and the right approach, replacing glass will not be a difficult task for you. Most importantly, do the work carefully, and everything will work out!

We insert glass into the interior door ourselves

Broken glass in the door of the room is a nasty thing, greatly spoiling the mood and interior of the apartment.

In addition, it is dangerous and fraught with cuts and other injuries. What to do? Painstakingly collect fragments and urgently engage in glass work.

Can't do without a specialist?

True, specialists do not recommend amateurs to master these very works. Design modern apartment so complicated and advanced that an amateur will most likely not be able to understand the design, will not understand the glass fastening scheme. Even a professional carpenter who is not familiar with the technological news of repair and with the features of your particular model is completely realistic to screw up this job. And you will pay for the glazing twice: to him and to the master for eliminating the marriage.

This is the case if you spent money on a good designer and a precious team of builders and your interior doors are decorated with glass baguettes, ruffles, colored stained-glass windows and mirrors.

If your apartment is the most simple, without bells and whistles and repairs you are used to doing with your own hands, you will not encounter any prohibitive problems in replacing the transparent rectangle between the room and the corridor.

Hopelessness with triplex

To begin with, let's figure out whose production your door is and how glass was attached to its canvas. Therefore, if it is veneered from the Ulyanovsk factory with glass 10 mm wide (with a standard of 4–6), then you still can’t do without contacting the master: this is a triplex, with the replacement of which you cannot cope without the help of others.

Triplex is attached only in the factory floor and is so expensive that it is cheaper to purchase and install a fresh door.

Option 1 (simple)

In Russian veneered economy class doors, glass is simply placed on top. In this case, we breathe a sigh of relief, measure the “vacated” opening with a tape measure or centimeter, go to the workshop, order a new glass - and carefully insert it. Lubricate with silicone gel; dries - remove smudges with a cloth.

An important point: do not forget to climb with a ruler inside the cell in which the glass stood and measure the depth needed to fix it. Traditionally, this is a centimeter or two. But if it is not added to the length and width of the future purchase, it will have to be repeated.

Option 2 (also "economy class")

It happens that the glass is fastened with a glazing bead with decorative nails.

In this case, you can also cope with its substitution on your own. We sigh with relief, measure with a tape measure ... (See the 1st paragraph of the text in the previous subheading. The 2nd, in general, also does not interfere with re-reading). The only difference is that after the broken or cracked glass is removed, the glazing beads are removed, and when a new one is inserted, they are put back and nailed with the same carnations that were originally there.

Option 3 (collapsible)

Suppose you have collapsible business class doors. This option is more difficult. The door will have to be taken apart. To do this, the bolts under the rivets are unscrewed from the sides of the door leaf, from below and from above. The main difficulty is to assemble the door back: distortions are possible!

Option four: if the glass is irregularly shaped

Even ordinary rectangular glass can be inserted when there is some experience in this matter.

If it is oval or generally zigzag ... It is important to guess with the size so that you do not have to take it again and again. It is better to take the dimensions of the broken glass onto cardboard. But the work must be jewelry. The permissible deviation from clear dimensions should not exceed 3-5 mm. And when using paper for removing patterns, it can reach 7 mm ...

In fact, there are even more options. Almost the same as the manufacturers of interior doors. In laminated, for example, from time to time the glass is attached to a glazing bead, which cannot be seen from the outside. Such a door cannot be repaired in general; it is not the glass that will have to be replaced, but its entirety.

But laminated though cheap.

It will be sad if you take on the repair of a designer door and break it completely ... So if you are not convinced of your own glazier's capabilities, it's better to call professionals. Or buy a fresh door. Therefore, there is a certain oddity here: branded door repairs will almost certainly cost you more than installing a new one.

Video: how to cut glass with a regular glass cutter

Replacing glass in an interior door: step by step instructions

Broken glass in the interior door? This does not mean that your interior glass doors cannot be restored.

You can completely replace the glass with your own hands, and the door will be like new. It all depends on how brave you are to take on such a job. Working with glass requires certain abilities. You need to follow safety precautions. The ability to perform glass replacement at home depends on which glass was installed first. Important qualities are: the method of fixing the glass and the type of door.

Let's see what can be done in each specific case.

Replacing glass in an interior door: a classic rectangle

The procedure for replacing rectangular glass is not complicated. The main thing is to do everything methodically and according to the instructions.

  • Splinters can be hazardous. Carefully remove the fragments from the door, collect them from the floor. To pull the fragments out of the door, slightly loosen the glazing beads (see below for how to remove the glazing beads). Observe safety precautions: wear work gloves. Reminder: before throwing away broken glass, measure its thickness.
  • Take the door off its hinges and lay it on a flat, level surface.

    If possible, do the work in the workshop, not in the living room.

  • If the glass was fixed on the glazing beads, carefully unscrew the screws that hold them on. If the screws are decorative, keep them. Check ordinary screws for rust and replace unusable ones. Most often, glazing beads are fixed with nails. Then pliers and a chisel will come in handy. With a chisel, pry off the bead and loosen it evenly.

    In this case, the nail head becomes available for gripping with pliers. Thus, remove all the nails and remove the glazing beads.

  • It is better to save decorative glazing beads in order to fix new glass with them. Glazing beads on interior doors are occasionally subject to decay, as is the case on window panes. Difficulties that may occur: scratched or broken glazing beads. Traditionally, scratches can be painted over with varnish. Broken glazing beads can also be glued, and the gluing points can be painted over with varnish or covered wax pencil in colour.
  • Remove old putty (or sealant) using a chisel, knife or awl.
  • Measure the height and width of the glass opening.

    Make sure the glass is square by measuring the height and width at various points in the opening. With a small error, it can be neglected by specifying the smallest length and width when ordering. The missing density is compensated by silicone and glazing beads. A large error (more than 5 mm) will require the order of glass in the form of a trapezoid. The result and speed of the following work depends on the accuracy of your measurements. Therefore, treat this procedure for us scrupulously.

  • For glass that has been inserted into a groove.

    Add to the height the depth of the cells in which the glass stood at the top and bottom. And to the width add the depth of the cells on the left and right. It is important that the size of the glass be 1-2 mm smaller than necessary, this will facilitate insertion into the grooves. Worse, if you specify a size larger than necessary: ​​the glass will have to be cut.

  • Order glass in a special workshop. Maybe instead of broken glass you want to put frosted glass, print, mirror or stained glass. Look at photos of interior doors with glass in different variations before making a choice.

    When choosing, consider in which room the door is located: you need to insert glass with a film into the nursery.

  • It happens that in the garage there is just a forgotten piece of glass, almost suitable in size. You need to reduce it a little. When cutting glass, be sure to wear safety glasses: even small fragments can severely damage the eyes. At the end of work with glass, carry out painstaking cleaning. After cutting the glass, file the edge with a file.
  • Fasten the glazing beads on one side of the door. Insert glass. If there are grooves, it is better to apply silicone in them in advance for durability and density.

    Fix the glass with glazing beads on the other side.

New glazing beads are best painted in the color of the door. Use stains or a special varnish.

Replacing glass with an increase in the opening

Suppose that after the glass fragments are removed, you want to make a door upgrade: change the shape or size of the doorway. It can completely replace the glass in the interior door with an increase in the opening with your own hands.


folding door

This option is available for self-replacement, if naturally the door design is not very intricate.

The glass replacement process is not complicated. It is difficult to disassemble and reassemble such a door. But if you still dare, proceed as follows.

  • Unscrew all screws.
  • Carefully disassemble the design. If there are a lot of parts, draw an assembly diagram. You can also stack the parts in a certain order, so as not to get confused during assembly.
  • Measure, order and insert new glass (or glass).
  • Assemble the structure again.

Sometimes the design of a door can be quite a puzzle. It's best to set the difficulty before you start the disassembly process. Therefore, you risk doing more harm than doing better.

It is better to order the experts to insert glass into the interior door. The cost of the question will be less than if the specialists fix your unqualified repair.

Sliding interior door

To replace glass or mirrors in sliding door You will also need to disassemble the entire door. And again, if you are not completely convinced of own forces, entrust the process to professional sliding door assemblers. If you want to complete the entire process of substitution on your own, be sure to do it with a partner.

  1. First remove the door from the profile grooves.
  2. The glass or mirror in the sliding door is protected by a special film.

    This simplifies its removal, as the fragments do not crumble. Carefully measure the broken glass and order a replacement (be sure to indicate the presence of a protective film in the order). In addition to glass, it may be useful to order a silicone seal for insertion if the old one is out of order.

  3. When putting the seal on the glass, remember the rule: it should be 5 mm shorter than the width of the mirror. To do this, freeze in advance and cut off the appropriate length.
  4. If the glass is installed between other types of filler (chipboard or MDF), connect these types to each other on a horizontal surface.
  5. The horizontal profile must be filled into the assembled filling with a mallet.

    Proceed with caution! It is not uncommon for glass to break during this process.

The installation of the vertical profile and rollers is done according to the usual scheme for assembling sliding doors.

What is impossible to do on your own

Types of glass that are difficult or impossible to install at home: triplex, glass with photo printing, some types of stained glass. Naturally, almost everything depends on the size of the glass and the difficulty of fixing it. But the main reason is not even in the fastening, but in the cost of these types of glass. An unskilled approach to installation is fraught with broken glass and foreign exchange costs.

Another option that is problematic to perform at home.

The glass is fixed in the door with the help of hidden wedges, which are inserted into a special groove. This is the so-called hidden glass fixation. The process of extracting wedges is best left to specialists.

On your own, you cannot replace glass in a radius door, corrugated or intricately shaped. Such a replacement will have to be ordered from professionals. The work is not done at home. From time to time, only the manufacturer will be able to insert glass into the interior door.

home › Repair › Replacement of glass in the interior door: step-by-step instruction

Did the glass in the door break or lose its aesthetic appeal? Do you need to replace the glass in the interior door - quickly, efficiently, reliably? Highly qualified specialists will come to your home, to any address in Moscow or its districts.

Why you should order from us

  • We carry out work of any type and complexity, regardless of shape, size and color in any door, whether it be wood, PVC or aluminum.
  • Our specialists work with the following glasses: display, window, stained glass, mirror, two-layer, tempered, reinforced, colored and patterned.
  • Choose one of two options for working with us:
  • call the glazier of the company "Lambrem-service" to the house,
  • or bring the damaged surface to the workshop yourself.
  • Additionally, in our company you can order a service such as door repair. In view of the fact that no one is safe from various extreme situations, Lambrem-Service offers emergency or urgent glazing.

Reasons for replacing broken glass in an interior door

Did the children play and accidentally broke the glass in the interior door? Because of the draft, the door slammed, and the glass shattered to smithereens?

In this case, the urgent replacement of broken glass in the interior door is a priority. Leaving fragments or without special skills trying to fix the problem yourself - threatens with unpleasant injuries. Urgently call the master to replace the broken glass, entrust this matter to a specialist.

Steps to replace broken glass

The procedure for replacing glass in an interior door consists of the following steps:

  • upon arrival, the master dismantles and removes the fragments,
  • takes measurements,
  • in the workshop prepare and cut the desired size,
  • the surface is ground and processed, if desired, the glass is tempered to enhance its strength,
  • then delivery to the customer follows, it is mounted and our master hands over the finished work to you.

To cooperate with us, you can choose any of the following ways:

  • departure of the master to your house
  • you can measure the required piece of glass yourself, but in the latter case, the company is not responsible for the error in your measurements, you are responsible for paying for glass work in full.

door glass replacement cost

The price of replacing glass in an interior door depends

  • from the kind
  • from sizes
  • from the surface material (aluminum, plastic or wood) of an individual door

You can calculate the final cost of the finished work by contacting an online consultant on our website or by calling a measurer.

The use of glass in interior doors is a popular technique in interior design. Glasses add airiness and lightness to the room, increase natural light, and just look good. But since glass is very fragile construction material, it is not uncommon for one part or all of the glass to be replaced. Broken glass cannot be left in the door, in addition to reduced aesthetics, it can be dangerous if the glass falls out completely or partially. Replacing glass in an interior door with your own hands is not difficult, you will need care, accuracy and a minimum set of tools.

Types of glass for interior doors

In many ways, working with glass depends on the type of glass that you have chosen for installation in the interior door. The most common are 3 types, the features of each must be taken into account while working with it.

  • Ordinary glass. The advantages of the material include affordable price, work with glass does not require special knowledge and skills. But after fastening ordinary glass, it will be required additional finishing leading to an increase in costs. Purchase glass either impact-resistant or cover it with a special film that prevents glass from scattering in the event of an impact - these secrets are also associated with an increase in the price of glass.

  • Decorative glass. In installation, decorative glass is as simple as the previous version. The choice of various patterns and types of decor will not leave indifferent the most whimsical buyer, everyone will find glass that will fit into his ideas about the future piece of furniture. Among the shortcomings, one can single out a rather high cost per unit of material, as well as difficulties in selecting new glass if replacement is necessary.
  • Organic glass. Plexiglas is not quite a derivative state of glass, the material is close to plastic in terms of characteristic qualities and operation. And this is both a plus and a minus of the material. The advantage of organic glass is its strength; it is not easy to break such an insert. The disadvantage of organic glass is the gradual change in appearance, over time it becomes cloudy. To avoid this, it is necessary to cover the plexiglass with a special composition in a timely manner.

Glass replacement tools


So that nothing distracts you during work, prepare in advance the materials and tools that you may need in the process.

  • Selected replacement glass, the right size, finished edges, safe to work with.
  • Gloves to protect hands from cuts. Thin garden gloves will not work, they will not save you from sharp glass in case the material falls and breaks, pick up strong special clothes.
  • From the tools you will need a chisel and a furniture hammer
  • Sealing paper will be needed to fit the glass to the size of the desired groove.
  • Prepare silicone to firmly fix the glass in the doorway.
  • Do not remove the broom and dustpan far away, sweep regularly during work to prevent cuts and splinters.

Glass replacement step by step


Replacing glass in an interior door in stages consists of several sequential procedures.

  • Remove the door from the hinges, put it on the floor, on a flat surface. Place a thick material under the door so as not to damage the canvas and the flooring. Make sure the door is firmly in place, it should not wobble or ride under you on the floor.
  • Using a chisel and hammer, loosen and carefully remove the glazing beads holding the glass in place. Carefully, using gloves, remove the glass fragments from the opening, check that there is no glass left in the door. Sweep the work surface.
  • Remove the lining, sealant residues from the opening. When replacing glass, these compounds will have to be replaced with new ones. Take advantage of the fine fraction.


  • Apply silicone around the perimeter of the opening. Use a spray gun for even distribution. Pull the protective gasket over the glass, install the glass in the opening. Apply a second layer of silicone, only on the other side of the glass.
  • Install the fixing glazing beads in their places, nail them with thin carnations. Let the silicone dry for a few hours, then hang the door on its hinges. Job completed!

Replacing the glass yourself is not difficult, this step-by-step instruction will help you do everything right. The main thing is to responsibly approach safety and the choice of new glass so that the result pleases you for a long time.