Repair 

Do-it-yourself cake turntable. Turntable for cake will facilitate the work of decorating pastries Rotating table for decorating cakes with your own hands


There is such a thing as a turntable. Some use it for presentations, any souvenirs. Confectioners are used to rotate the cake during the manufacture of the latter. I decided to make a turntable with my own hands to show my homemade products, such as in "3D". The motor was taken as a basis microwave oven. Makes almost 3 revolutions per minute. It is powered by a 220V household network.

For the design of the table we need:
- a circle of plywood;
- plywood rectangle;
- switch;
- aluminum corner, for mounting the switch;
- network cord;
- screws 10 pieces;
- Microwave motor.


The first step in our base is making a cut under the motor. It turned out somehow crooked, but that’s not the point, it will be closed by the table itself. Base dimensions 250mm*100mm, plywood thickness 18mm.


We drill a hole with a diameter of 6 mm in the pancake of the table, the axis of the motor is 6.5 mm. The hole is not through, but exactly the length of the axis of the motor (about 10 mm). Trying on. Comes in tight. If you drill the same diameter as the axis of the motor, then the table pancake will hang out. It will have to be glued, and this additional time for making homemade.

Be sure to look at the motor. They are not 220V. I got 21V. In the latter case, a transformer is needed, it can be powered from the control board of the same furnace.


Since I have plywood BU, I decided to paint the pancake and the base of the table from a spray can. Matte black paint was available. Everything dried quickly. Along the way, I drilled a hole for threading wires.


After the paint has dried, we fasten the motor to its permanent place. I took the screws from an old printer. Very successful because of the wide hat.


We pass the wires into the hole from the side of the bottom of the structure. We unsolder the switch, I have a toggle switch TP 1-2. We attach the corner to the base. We fasten the toggle switch to the corner. If there is no corner like mine and another switch, then you can make something for your needs.


So that the design does not go around the table, I decided to install rubber legs. I used medicine caps as legs. In general, it is very convenient to use such legs in the manufacture of cases, homemade products. Rubber is very flexible. I screwed them onto all the same screws from the printer.


Pancake table in my case 230 mm. The thickness is the same 18 mm as at the base. Fits perfectly for my needs. This is the table I got. I repeat, it makes almost 3 revolutions per minute.

It is very convenient for confectioners involved in the manufacture of cakes to use various kinds of devices that facilitate the decoration process. finished product. Fortunately, today shops offer wide range of similar inventory. One such device is the turntable. True, the cost of such a table is rather big, and it is often easier and more profitable to try to make a turntable for a cake with your own hands.

What is convenient?

Such a table is useful not only for professional pastry chefs. It will be very useful for those who like to cook for their own pleasure, as well as cooks taking their first steps. By the way, such a table will come in handy for housewives decorating cakes with mastic. It looks like a circle-pedestal on a leg that rotates around its axis. The main goal is to make the work of the confectioner as ergonomic and convenient as possible, to simplify the task of decorating the finished cake. The cake is placed on a stand, and by rotating it, you can easily cover it with mastic, decorate it with figures, inscriptions and other decor. At the same time, there is no need to walk around it, the confectionery will rotate on a stand, and the hostess will have access to any place on the cake.

What will be required

In order to make a turntable for a cake with your own hands, you will need:

  • Bearings — 2 pcs. It is better to use double pressed bearings.
  • Wooden blank for a circle. It could be the door old furniture or any chipboard material, available.
  • Nails.
  • Self-tapping screws.
  • Tube (made of plastic or iron).
  • Iron circle (metal).
  • Plywood sheet.
  • Plastic or decorative self-adhesive film.

How to make a turntable with your own hands

This process is not too complicated, but requires male participation. To begin with, it is worth drawing a drawing of the future stand and preparing all the necessary elements.

If the bearing is not double, then two will be required, and one must fit into the other.

  1. We push the smaller bearing into the larger one using nails.
  2. From a chipboard blank (or an old door), we cut out two circles with an electric jigsaw, equal to a diameter of 20 cm.
  3. In one of them, a hole should be made in the center into which the bearing is placed. It is this technique that will ensure the turning of the entire mechanism.
  4. We attach the second circle with self-tapping screws (you can use liquid nails) to the first.
  5. The bottom circle, which does not have a hole, will stand directly on the table.
  6. Then a plastic tube is inserted into the bearing (you can use an iron one, if available). It will connect the base and the top - the pedestal for the cake. The tube must fit very precisely into the bearing so that it does not hang out, otherwise it will be difficult to use the turntable. The optimal length of the connecting tube is 15-18 cm. In this case, it will not be too short and too long, it will be most convenient to use the device.
  7. The top (the stand itself on which the cake is placed) is best made of metal. You will need a metal circle, which is 30-40 centimeters in diameter. It is attached to the top of the tube (metal or plastic) by welding. Of course, not everyone has a welding machine and a person who knows how to do it at home. In this case, you can use cold welding, reminiscent of plasticine.
  8. Plywood or chipboard is attached to the top of the metal circle, equal in diameter to the metal circle, using liquid nails or self-tapping screws.

Now the do-it-yourself cake turntable is almost ready. It remains only to add aesthetics to it. To do this, the top is pasted over with wallpaper-film or a plastic round base. This will give the fixture a finished look and facilitate maintenance.

As you can see, if you want to make a turntable for a cake with your own hands, it’s not so difficult. A set of materials for its assembly can be found in almost any home, and the work process itself is not so complicated.

What can replace the cake turntable

What is the way out for those who do not have a turntable? A very simple and affordable solution is also available in almost any home. You can use a microwave turntable. Almost all models are arranged in such a way that they have a glass plate and a round stand at the bottom. It is necessary to get a plate and a circle under it from the microwave. If it is too smooth, you can put paper (paper towel) down to reduce slip. Thus, you can decorate the cake by smoothly rotating it around the axis. Also, a glass plate will not spoil the view when serving a finished decorated product.

Baking cakes is not only interesting, but also responsible. The aesthetic appeal of the confectionery product and the ability to arouse the appetite of consumers depend on the quality of the decoration. Therefore, without a special rotating round table, intended for decorating sweets, is indispensable.

The stand consists of several parts. Using step by step instructions, a turntable for a cake can be made by hand.

What is a turntable for?

The swivel cake table is a great find for those who are fond of baking complex confectionery.

The device has the following advantages:

  • greatly facilitates the final processing of the cake, rotating around its axis;
  • the confectioner can decorate the product without moving, which greatly speeds up the cooking process;
  • often on the surface of the table there is a special marking that allows you to create even and neat elements.

The rotating support will help professional confectioners and ordinary housewives to create culinary masterpieces.


Features of choice

In order not to make a mistake when choosing good table, it should be evaluated according to several criteria.

Swing mechanism

The most important part of the model, without which the table simply will not spin, is the turning mechanism. It is a metal bearing, located under the tabletop, providing it with uniform rotation around its axis.


Diameter

The most common countertop diameter is from 26 to 30 centimeters. Such parameters have a cake of standard size up to four kilograms.

But for convenience, it is better to choose a larger diameter so that during operation you can lean on the countertop with your hand with a palette. This will help achieve a more accurate result.


Silicone feet

A necessary part designed to fix the structure in one place. This prevents the confectionery product from slipping on the surface of the countertop, thereby eliminating possible defects and damage to the cake during processing.

Such legs are quite inexpensive, in the region of several hundred rubles, but thanks to them, the product will turn out to be perfectly even and without damage.


markup

On the round surface of the tabletop there are special divisions that divide it into equal segments. This is the markup that helps to create completely even and uniform decorative details. In addition, the parts of the cake will be located at the right angles, which will certainly ensure a high-quality end result.

In the event that there is no marking, you can apply it yourself using a ruler and a compass.


How to DIY

The modern market offers many devices to facilitate baking products. However, by making a cake turntable with your own hands, you can save a lot of money. In addition, a home-made design can be created from your own materials, adapting it to specific requirements.

Necessary tools and materials

To create a model, you can use various materials. The most common options are wood, plywood, chipboard.

To work, you will need the following tools and materials:

  • pressed bearings, 2 pcs.;
  • lumber;
  • thin plastic;
  • metal circle;
  • pipes made of plastic or metal;
  • nails;
  • self-tapping screws.


Further instruction will be devoted to how to make a do-it-yourself plywood rotating cake stand, as this is the most convenient and inexpensive option.

Manufacturing

Before starting work, you should make a drawing, indicating on it the details that the model will consist of, and their dimensions.


Creation instructions:

According to the drawing, two circles of the desired diameter are cut out of plywood - 20 centimeters.


A bearing is inserted into one of these circles. The hole for it is cut out in advance.


Two parts are twisted and fastened with self-tapping screws, and the bearing is inserted into the center.


The upper and lower parts of the table are connected using plastic tubes, if desired, metal tubes can be used.


They must fit very precisely into the bearing. The most optimal length tubes - 15 centimeters. Top part models are made of metal. Its size plays a very important role, so it is best to make a diameter of 30–40 centimeters.


The parts are then connected to each other with welding machine. You can also use hot glue for bonding, which hardens when cooled. Next, the rotating circle is placed on the pipe and fastened with self-tapping screws.


The finished table is decorated in different ways. For example, the surface is decorated with crepe paper or thin plastic.


Video

Watch a video about making a wooden turntable with your own hands.

Do-it-yourself cake turntable is needed not only for real confectioners. This is a necessary item for those who cook for pleasure. Housewives who bake mastic-coated cakes cannot do without such a design. The main purpose of a turntable is to facilitate the process of decorating a cake. That is, you do not have to beat around and around the finished product, it will be enough just to decorate a rotating cake. Baking spins around its axis, and you only need to have time to decorate it.

How to make a turntable? Get everything ready to start necessary materials. You will need two bearings, which are available from auto parts stores.

Please note that there are double, compressed bearings. The second option is preferable because you will have to tinker less.

The turntable also needs a wooden plate. You can stock up on the door from kitchen set. In addition, you will need hard nails, self-tapping screws, plastic tubes, a metal circle, thin plastic, plywood.

Work process

Scheme Drawing

Making a turntable with your own hands is quite simple. First of all, you will need to draw a quality drawing. After that, we begin to work according to the following scheme. If you have two bearings, and not one pressed one, then we drive an element of a smaller diameter into a larger one using nails. It is necessary to cut out two circles with a diameter of 20 cm in a wooden plate. In one of the circles, a hole is cut in the middle into which the bearing is hammered. In this case, the two parts are twisted and fixed with screws. The bearing is placed in the center.

The do-it-yourself table is equipped with plastic tubes. The tube should connect the upper and lower parts. Consider this point when you make a drawing for the turntable. In this case, the tube must fit exactly into the bearing. The ideal length is 15 cm. Such a tube will not be too short or long, so you do not have to bend down to decorate the product.

The top is made of metal. In order for it to spin, pay special attention to its diameter. On average, the diameter of a metal circle should range from 30 to 40 cm. If you have the opportunity to weld the elements, it will only be wonderful. For those who are deprived of such an opportunity, cold welding was invented, which looks like plasticine. A cake turntable also requires circles cut out of plywood. The rotating part is mounted on the pipe, and the elements are fastened with self-tapping screws.

1 2 3 4
5 6 7

The table can be made of wood:

Cake turntable

Bearing Assembly of rotation
Table top base Rotating part assembled
Cake turntable (bottom view) Cake turntable (side view)

In the arsenal of every pastry chef there should be a rotary for cakes.

With it, you can greatly facilitate the process of decorating cakes and make it pleasant, comfortable and safe.

If the purchase is not planned in the near future, then an experienced craftsman can assemble it on his own.

If you want the cake to be accessible to you from all sides at the same time, and at the same time you would not have to run around it, be sure to consider having a rotating stand.

What is a turntable for cakes? This product is made up of:

  • round work surface;
  • – grounds;
  • rollers, rubber bands

Thanks to its design, the table easily rotates around its axis, and provides convenient access to the confectionery product. With such a supply, you can create elegant and original decors and create decorations of any complexity. At the same time, you don’t have to worry at all that your masterpiece will move out, get damaged or fall to the floor.

The cake turntable can be purchased from ready-made and do it on your own. Homemade design has a lot of advantages. First, you can make a product that will fully meet your requirements and preferences. Secondly, you yourself will be able to create a well-thought-out drawing of the product, select the materials for its manufacture and think over the most optimal dimensions. Besides, homemade construction will be much cheaper than store bought.

materials

A swivel table can be made from any improvised materials:

Each individual option has its own advantages. The tree is environmentally friendly, safe, pleasant to the touch texture. MDF and plywood are easy to process. In addition, this material has a low cost.

But chipboard is inexpensive, and its appearance is attractive, and it is pleasant to work with it.

Advice: in order to save Supplies, for the manufacture of countertops, you can use the door from the old kitchen set.

Instruments

Having decided to make a DIY turntable for cakes, prepare the following: tools and materials:

Important: bearings are double and pressed. The second option is preferable when assembling a rotating cake stand, as they are easier to install.

How to make a turntable?

Making a turntable is quite easy and simple. First you need to make a well-thought-out sketch. On this drawing, indicate the design of the product, its exact dimensions and materials of manufacture. With such a scheme at hand, you can easily assemble a table the first time and without errors.

The manufacturing process of the turntable is carried out in the following sequence:


That's not all difficult process production of a rotating structure.

Advice: to give the product a decorative appearance, it can be pasted over with thin plastic.

Also, the product can be decorated with a self-adhesive film. It just sticks on and is easy to wash.

A photo

By choosing different materials and getting creative, you can get very different tables.