loops 

In what cases it is possible to lay new linoleum on the old one. Is it possible to lay linoleum on linoleum - four basic conditions How to lay new linoleum on the old one

Reading time ≈ 6 minutes

Linoleum is not a complicated process, but it is time-consuming and requires compliance with many recommendations. The most important is preparatory stage, implying the preparation of the floor surface for the flooring of the finish coating. Therefore, many are afraid not of the repair process itself, but of a series of preparatory work. All these pre-laying activities are associated by many with devastation, disorder and a lot of building dust. For this reason, some people prefer to lay fresh linoleum over old linoleum and wonder if it can be laid over existing similar flooring.

It is believed that the best option- It's all the same to remove the old coating. There are several reasons:


There are cases when the old linoleum must be removed without fail: if you find blisters, old and worn material in places, as well as large irregularities on the floor. A complete replacement of the coating is also required in the event of obvious holes, dents and wavy areas.

If you laid linoleum recently and leveled the base well, then such a coating most likely did not have much time to deteriorate. Defects on the floor have not yet become noticeable. In this case, you do not have to bother with fresh flooring for a long time, you can lay new linoleum over the old one. Provided that the laying of the previous coating was done with high quality and professionally, it can serve as an excellent tool for soundproofing.

Advantages of laying a new coating on top of an old one

So is it still possible to lay linoleum on the old surface of linoleum? This laying technology has several advantages:

  • You do not waste time performing floor screed work or dismantling old linoleum.
  • Before laying linoleum, you perform a minimum of preparatory activities.
  • Your floor will have sound and thermal insulation properties without additional installation.
  • The two-layer coating has increased softness, which in some cases is a plus.
  • You save a lot of money.
  • Having received a two-level coating of linoleum, you exclude the possibility of excess dirt and dust entering the room.

Material selection

In order for the floor covering to be of high quality and last for a long time, the choice of material must be taken seriously. What are the criteria for choosing linoleum:

  1. Wear-resistant and high-quality household linoleum should have a protective layer thickness within the following parameters: 0.35 mm, 0.36-0.6 mm, more than 0.6 mm.
  2. This type of linoleum is used for rooms such as a living room or a bedroom, since this implies a minimum load on the floor surface.
  3. Commercial linoleum is used for floor surfaces in offices and industrial premises, the thickness of the protective layer can be from 0.7 to 1 mm.

High quality linoleum

Repair is a difficult and very dirty business. Often we delay its beginning, fearing the onset of devastation and an abundance of garbage. However, there are options for implementing individual repair work practically free of dirt. For example, you have put in order the ceiling, walls, window and door openings, and the only thing left is the floor. If your choice fell on such a democratic flooring as linoleum, then you can consider laying it on a similar old flooring. In this case, you will not suffer from a huge amount of dirt and dust.

To begin with, the possibility of laying a new linoleum on an old analogue is being evaluated. The first rule of laying linoleum is the obligatory presence of a flat surface. Therefore, you need to assess the condition of the old linoleum:

  • are there any holes;
  • are there any cracks?
  • are there air bubbles;
  • are there any non-glued places;
  • how old linoleum is fixed.

Repair of old linoleum

If there are holes, the option of laying a new linoleum on the old one is not even considered. However, with a strong desire, you can carefully cut holes in the shape of rectangles, and insert linoleum patches of the same thickness. You need to take a suitable piece, cover the hole with it and cut the patch and the hole at the same time with a sharp construction knife. Secure the patch with glue. Then seal the joints with sealant, leveling the surface. This is a painstaking business and it is up to you to decide: is it worth it? Losses in this case are not taken into account.

If there are cracks, laying on the old linoleum is possible, but preparatory work must be carried out. Be sure to remove dust from cracks and treat them with sealant. Then level the surface with a rubber spatula and leave to dry completely.

Air bubbles should be smoothed out and fixed with glue using a syringe, while installing something heavy.

The same must be done with non-glued places.

If the old linoleum was not glued, but is attached only with skirting boards, it should be removed. It is not recommended to lay new linoleum on such a surface.

Be sure to pay attention to the presence of fungi or rotten parts. It is absolutely impossible to use such a surface for laying new linoleum.

View selection

It will be correct in this case to put thin linoleum only if there is a substrate. There is a risk that when installing on an old linoleum, a new coating may break through. It is better to use a linoleum coating on the base or lay the base separately under the new linoleum.

By manufacturing technology

  • homogeneous;
  • heterogeneous.
  • commercial;
  • semi-commercial;
  • non-commercial.

By way of application

It can be said that the most the best choice- This is a homogeneous commercial linoleum. However, the pricing policy of this direction can bite for many. Therefore, how to make the right choice is up to you.

The subtleties of choosing linoleum (video)

Preparing for styling

Work should begin with the complete release of the floor from furniture and other items. You should be able to completely spread the piece of linoleum you need.

Then you need to remove the old skirting boards. Their further use is possible, then they must be removed carefully so as not to damage them. You can also update them by painting them to match the new linoleum.

Before you put the old linoleum, you need to wash it well and degrease it. The next step is priming. Old linoleum is carefully primed to enhance the bond between new and old. Also, in addition to improve adhesion, you can walk with sandpaper on the old surface and it will be right.

DIY installation process

The process of installing a new linoleum on the old one is the same as the usual one. Spread new linoleum on the prepared surface. Lay two edges close to the wall, and cut the other two, if necessary, with a special construction knife. If there are ledges in the room, then you need to cut out a piece of linoleum with a margin. Leave the linoleum for leveling in the unfolded state for several days. In places of folds, you can install something heavy for alignment. Then correct the laid-back pattern.

Trimming and laying linoleum (video)

Special glue is applied to one half of the coating, then to the other. To prevent air bubbles from collecting, you need to smooth from the middle to the edge. Do the same work on the other side. Leave to dry, then fix the skirting board. It is believed that in rooms up to 25 sq. m you can not use glue, but it will be enough just to fix it with skirting boards. In this case, linoleum is used in one piece for the entire room.

If you need to lay two or more pieces of linoleum, then you need to carefully control the lack of coincidence of the joints of the lower and upper coverings.

Linoleum laying master class (video)

Conclusion

In conclusion, I would like to highlight the positive aspects in laying the new linoleum on the old one. There are several advantages of this option for laying linoleum. First, the presence of dust and dirt is reduced to a minimum. Secondly, it is not necessary to carry out dismantling work with old linoleum. Thirdly, there is no need to make a screed. Fourth, you get additional soundproofing. Fifthly, the floor is additionally insulated. Sixth, the floor becomes softer. Seventh, which is also important, is material savings. Eighth, the time spent on repair work is reduced. All these advantages are enough to bring the idea to life in your kitchen!

Is it possible to lay linoleum on old linoleum, it is impossible to answer right away. First you need to examine the state of the old floor covering. Of course, I would like to do all the work as quickly and easily as possible. But in this case, haste can harm the new floor. Mounted linoleum will not last long and will have to be changed again.

When the old coating must be removed

Linoleum in Soviet times was considered one of the most available materials floor covering. It could be seen on the floor in every apartment. In some it is still preserved. However, over the years, his attractive appearance disappeared. Urgent replacement required.

It would seem that this operation is very simple. Just need to lay another linoleum on top. However, the following components will also go with it:

  1. Dust. For many years, dust has collected under the old linoleum. This is especially true for hard-to-reach places where there was practically no cleaning. In addition, earlier linoleum was made on a fabric basis. This material is not dust resistant. He either accumulates it in himself, or has long been rotten. If you do not eliminate the old linoleum, then in addition to the new flooring in the house there will be a smell of old rotten material and dust.
  2. Dirt is firmly embedded in cracks and seams. In places where it accumulates, bacteria begin to form, which pose a threat to the health of others.
  3. If the old linoleum has peeled off in some places, then this is the first sign that it should be eliminated before laying a new floor covering. Installation of linoleum should be carried out absolutely on a flat surface without bends and distortions.
  4. An uneven surface can be on the old linoleum, not only because of its delamination, but also after the formation of holes, waves, dents. Especially if these curvatures are more than 2 mm per 2 square meters.

Rules for removing old linoleum

To make the process of eliminating the old floor covering faster and more efficiently, you need to cut the linoleum into separate strips. Removing a panel of this size is easier than opening linoleum completely glued to the floor.

In order to lift the glued part of the linoleum, you need to use a scraper or spatula. Professional craftsmen have a special jack scraper. It is equipped with a detachable grip.

If you cannot remove the old glued linoleum with a conventional spatula, you must use a grinder or an electric cutter.

Laying new linoleum on old

If the repair in the living room was carried out quite recently and the old linoleum is in excellent condition, then a new floor covering can be laid on it. This also applies to linoleum. This happens when you just want a color and texture update on the floor. Or just the old linoleum does not fit the newly purchased furniture.

Installation order:

  • Old linoleum must be thoroughly washed, dirt and dust stuck in the seams should be removed. After this, the floor covering should be treated with an antiseptic and dried. The relative humidity in such a room should be no more than 65%, and the air temperature should be in the range of 18-24 degrees.
  • New linoleum must acclimatize indoors. After buying it, you need to hold it folded for 2-3 days.
  • Next, cut out the desired size of the flooring. This should be done especially carefully in doorways and at the locations of communication pipes.
  • The material is leveled on the floor and given another day to get used to the new floor.
  • Directly the installation of the new linoleum on the old one.

Additional Information:

  • Linoleum is a versatile flooring. It is used in repairs much more often than other coatings. The laying work is not that difficult and…
  • Whether it is possible to lay laminate on linoleum depends on the condition of the old flooring. In any case before...
  • Carrying out work on removing linoleum from the floor is a very laborious process that requires special training, as well as certain skills and…
  • Is it possible to lay linoleum on old carpet? You can answer this question in the affirmative, since both of these floor coverings ...

Such a floor covering as linoleum has been known for a long time. But to this day, it is in fairly wide demand among the population. After all, the price of this type of flooring is relatively low, working with it does not require special skills. And linoleum is quite wear-resistant and beautiful. And a huge number of colors allows you to choose a coating of this type for absolutely any interior.

Is it possible to lay new linoleum on the old

Is it possible to lay a new one on the old linoleum? This is a rather controversial question and it is simply impossible to give an unambiguous answer to it. The most important criterion will be the condition of the old finishing material. The thing is that if it is all torn and wavy, then it is definitely worth throwing away. But what to do if it is in almost perfect condition, and just did not match the color of the new interior?
Here it will be important to take into account several criteria:

  • If the old coating rests only on the baseboards, then it would be best to remove it.
  • The old linoleum is planted on glue and it is simply impossible to tear it off the floor. In this case, it will be possible to lay a new layer of finishing material on the old one. However, the surface must first be prepared.
  • In the event that linoleum has lain on the floor for many decades, then it must be thrown away. This is because the substrate has probably already rotted and has become more like dust. And as a result, the new coating will not last long and will soon become unusable.

In what cases it may be necessary to lay linoleum on linoleum

Of course, all experts, without exception, would advise putting such a finishing material as linoleum on a flat, prepared floor surface. But there are cases when a new coating of this type is laid on an old layer of linoleum. Namely:

  1. The old layer of linoleum was recently laid and is in good or even excellent condition. I just didn't like the color or pattern.
  2. Previously, the bedding was glued and it is quite difficult to tear it off. But this is provided that its surface is in good condition.
  3. And it happens that the owners have no desire to breed dirt, but they want to make repairs.


How to prepare the surface for laying linoleum

Due to the fact that the new coating will be laid on the old linoleum, its surface requires special preparation, which must be carried out.
The first step is to free the room from everything superfluous, or rather, take out the furniture and things, and remove the baseboards. Then, it will be necessary to thoroughly wash the floor surface and only after that mark all those places that require adjustment. And these are: dents, cracks, gusts, bubbles and so on.
Small cracks and small rips can be repaired with a sealant. They carefully fill the crack, and after the sealant dries, level the surface. In the same way, it will be possible to eliminate small dents.
In order to align the bubbles, you will need a syringe and special glue. Enter not a large number of adhesive under the linoleum using a syringe, and then put the load in this place.
Large damage is repaired with patches. To do this, you will need to find a material of the same thickness. After that, using a ruler, you need to carefully cut out the damaged area, and put a slightly smaller patch in its place. It must be glued, and the seams between the linoleums can be coated with welding for this type of coating.

Which linoleum should be preferred

In order to choose a suitable linoleum, you should pay attention to the condition and some characteristics of the old coating. So, for example, if you want to improve noise and heat insulation, then in this case you should prefer linoleum on a thick substrate. But then it is worth considering that the floor surface will rise, and if there are doors that open inward, then they will need to be cut from below or lifted by moving the hinges.
In the event that the old finishing material is in good condition, then you can purchase linoleum without a substrate. But here it is important to consider that if there are even slight irregularities on the surface of the old linoleum, the new finishing material can tear very quickly in such places.
It is best to purchase linoleum of such a width that it can completely cover the floor surface. If this is not possible, then try to keep the seams as small as possible.

We prepare linoleum

Before proceeding to the actual finishing, you will need to prepare a new linoleum. To do this, it should be spread on the floor surface and cut in such a way that the edges of the old and new coatings coincide. After that, it is recommended to leave it for at least a day in a spread state. This is necessary in order to even out all the waves and the surface of the coating has become almost perfectly flat. It is worth considering that it may take much more time to completely level the linoleum.
Too strong bends should be straightened with heavy objects. They are simply installed on the kink so that it aligns.

We fix linoleum with skirting boards and double-sided tape

With the help of skirting boards, linoleum can be fixed, provided that the area of ​​​​the room does not exceed 10 square meters, while linoleum should be solid. You will need to size the material, let it rest, and then attach the skirting boards in such a way that they firmly press the finishing coating.
Laying linoleum on double-sided tape is somewhat more complicated and is required for rooms larger than 10 m2. To do this, the stale linoleum must be bent to about half. Then stick strips of adhesive tape on the surface of the old linoleum over the entire width of the room. Leave a gap of no more than half a meter between the strips. The last strip of double-sided tape is glued along the edge.
After the adhesive tape is pasted, it is necessary to gradually lower a new coating on it and iron it with a special roller. When one half is fixed, exactly the same procedure should be carried out with the second. At the very end, you need to install skirting boards.


How to lay linoleum on linoleum using glue

In the event that the area of ​​\u200b\u200bthe room is more than ten square meters, then special glue can and should be used for laying linoleum. And in no case do not use double-sided tape to fix the finishing coating if the area is more than 20 m2.
To begin with, you should wait until the linoleum rests and prepare the glue. After that, you need to lift half of the linoleum and, starting from the baseboard, apply an adhesive to the previously prepared surface. Then the new linoleum is carefully lowered and smoothed out with a roller. The same procedure is carried out with the second half. Skirting boards are installed in place only after the glue has completely dried.

Advantages and disadvantages

Such a procedure as laying a new linoleum on an old one has a number of positive and negative sides. So, what are the advantages:

  1. Due to the fact that there is no need to remove the old coating, the finishing process will take less time.
  2. There will be very little dirt, due to the fact that the old linoleum will not be torn off.
  3. If the new linoleum is on a thick substrate, then the sound and heat insulation in the room will increase significantly. The surface of the floor will become much softer.

However, there are also disadvantages:

  1. There is a certain risk that a new finish applied over an old one may ripple over time.
  2. If before laying the new linoleum, the surface was not properly prepared, then regardless of the thickness of the substrate, all the defects of the old finishing material will soon appear on the new one.
  3. It may take a long time to eliminate all defects in the preparation of the floor surface. This is if there are quite a few of them. It can also be difficult to select material for patches, because it must be the same thickness as the old coating.

In what cases it is necessary to remove the old layer of linoleum

There are cases when the removal of the old linoleum is inevitable, and there are several of them. So, in what cases do experts recommend removing old linoleum:

  1. It is definitely worth removing and throwing away the finishing material purchased back in the days Soviet Union. The fact is that even if its surface is in a fairly good condition, then the substrate of the material (namely, it was used in those days for its manufacture) by this moment can completely crumble. It also accumulates dust and dirt.
  2. If a decent amount of dust and dirt has accumulated between the seams.
  3. If the old linoleum is badly damaged.
  4. When the floor surface is uneven. Then it is recommended to remove the finishing material and level the floor.

It is possible to lay new linoleum on the old one, but only in specific cases. And not a single builder will give you an exact answer without seeing the condition of the old coating.

During the period of repair work in the apartment, almost anyone seeks to minimize financial expenses. This also applies to replacing old linoleum with new. Most people do not want to spend a lot of time and effort not to do surface preparation work, often wondering if it is possible to lay linoleum on old linoleum?

In this article, we want to explain in which cases the old coating can be left on and how to properly lay new material on it.

Is it worth laying new linoleum on old?

Putting a new coating on the old one is certainly possible, provided that the past linoleum is in good condition. As a rule, the replacement is made according to two circumstances:

1. The old coating does not match the interior of the room;

2. Outdated and worn previous coating.

As for the second reason, it is necessary to examine the linoleum for defects and evaluate the quality of the coating. If it is worn out and has severe wear or bumps, then it should be removed, since the laying of the new material will exactly repeat the bulges of the past.

If the surface of the old linoleum is straight, and it does not contain any obvious flaws, you need to pay attention to its service life. For example, if linoleum was made on a fabric basis, which peels off and diverges after a while, turning into dust, i.e. if the old coating is more than 13 years old, then it is better to remove it, regardless of what condition it is in. If the floor material is relatively new and well fixed, but has shortcomings as a result of operation, then they should be eliminated and then only it will be possible to use the old one.

In what cases it is worth removing the old linoleum

Of course, there are cases when laying a new coating on an old one is not only not recommended, but extremely unacceptable. This is due to such reasons as:

1. Deformation of the old linoleum - there are folds, scuffs, swelling, breaks or other defects in the linoleum;

2. The presence of mold - it does not matter where the mold is located, on the inside or outside. Its presence already indicates the unsuitability of this coating.

If the previously used linoleum contains minor flaws, for example, it is somewhat torn in some areas, then it is possible to restore it in advance. Torn shares must be blinded. At the same time, it is important to remember that it is impossible to eliminate cracks using compounds with polyester elements. These elements can later be a factor in the loss of color of the new coating.

The process of laying new linoleum on old linoleum

At the initial stage, it is necessary to remove furniture from the room, remove all unnecessary up to floor plinth. The work area must be completely empty and free to act.

The surface must be thoroughly cleaned and carefully examined. Without exception, all existing cracks should be covered with mastic or silicone sealant. The plane is smoothed with a rubber spatula. After the used material has dried, you can start laying linoleum.

When choosing a canvas, the width should be taken into account so that there are fewer cuts and joints. First, we spread the linoleum around the room so that it straightens out. If it lies unevenly, we put the load.

Joints can be combined in various ways. Specialists use hot welding for this. A wire is inserted into the nozzle of the building hair dryer. A section is made between the sheets, equivalent to the width of the cord in which it is placed and instantly melted.

Repair of the old coating

Linoleum that has been lying in the room for a very long time can be seriously deformed. Serious damage to the canvas includes: deep cuts and tears, punching from furniture, swelling.

Repair of cuts, tears, punctures, seams.

Before laying the new linoleum on the old linoleum, it is necessary to prepare the old base, namely: you should wipe the edges of the torn material a little, in such a way as to eliminate burrs and various tubercles, it is necessary that the glue flows freely to the full depth, it's okay, if there is a gap, it will be completely filled with glue.

Then thoroughly clean the adhesive area, make sure that there is no moisture there. If possible, glue the edges of the linoleum to the floor with double-sided tape or register them thoroughly during the repair period.

Application of adhesive: Wear protective gloves. Squeeze superglue into the gap along the entire length. The C-type glue is quite dense, and you can not beware that it will end up on the outer plane of the old linoleum. If you have formed a bump, do not rush to eliminate it, this can be done after drying.

Finishing: after hardening, carefully cut off the bumps of the glue. If you want, the seam can be additionally hidden with mastic for linoleum.

Repair of punctures and small holes

If the hole in the old linoleum is less than 1-1.5 mm in diameter, then it is possible to simply fill it with A-type glue, this is a liquid glue for welding a new coating. To do this, stick masking tape into the hole, create a hole in it above the puncture and under its volume, so that pieces of adhesive tape do not go deep into the linoleum. Put some glue in there. After drying, remove the tape and cut off the glue bump.

If the hole has a diameter of 1.5 millimeters up to a large coin, in this case it is possible to fill it with C-type glue (this is what we talked about more), everything is the same without exception, only there is no adhesive tape.

Technology and rules for removing old linoleum

Removing a worn coating is a simple problem, everyone is able to cope with it. Let's take a look at the main points so that everyone can cope with this:

1. Clearing the territory. This procedure includes the removal of entire furniture, the removal of decorating components, shelves, etc.;

2. We divide the linoleum into equal parts with a sharp knife. Small pieces peel off from the base much faster than a solid coating.

3. If you heat the material with a hair dryer, then it will become softer and easier to clean.

4. Work easier manually. After you lift the strip with a spatula or other device, remove it further by hand.

Answering the question: is it possible to lay linoleum on linoleum - you can, if you take into account different nuances and follow the rules for laying a new canvas.