Do you want to decorate your summer cottage? Why not use the simplest and most affordable material - plastic bottles? Today, with the help of this raw material, various figures of animals and plants are created. Differing in durability and wear resistance, such handicrafts do not need care, perfectly tolerate any weather conditions and will delight your eye at any time of the year. The topic of this article is plastic bottle swans for the garden with their own hands. In it, we will discuss how to make such a decor as quickly as possible and what is needed for this.

Swans from plastic bottles for the garden

Swans from plastic bottles - beauty and functionality

Swans are always very beautiful and romantic. But we offer you not only to enjoy plastic swans but also think about how to make them functional. For example, some people use a finished swan figurine as a flowerpot. This design is ideal for landscape design your site. The best part is that for its construction it is not at all necessary to be a master and own a special tool. Such a product will be affordable even for beginners.

You will need the simplest materials: large plastic bottles of 5 liters - 2 pcs., Wire, metal mesh for wings and putty. Usually, all these materials remain after repair or construction work.

The main stages of work on creating swans from plastic bottles:

Stage 1. First you need to cut a hole in the bottle to create a flower bed.

Stage 2. To give the bottle a rounded shape, it is recommended to fill it with sand so as to form a circle. This flower bed will also be the body of the swan, so it should be slightly oval.

Stage 3.

Stage 4. Preparation of the base. To do this, it is necessary to displace a certain amount of putty, spread it on a plastic film with a layer of 5 cm and put a bottle with a hole on top. Leave to dry for a while. As soon as the putty dries, it will turn into original stand under the swans To make it easier to work with putty, it is necessary to moisten the spatula periodically a small amount water.

Stage 5. Creating a graceful swan neck. To make the neck look attractive and preserved on long time, you need to roll up small rollers of putty and press it into a metal bar. A large piece will fall off immediately, so the best solution is to create a neck from small pieces. After the next piece, the neck is wrapped with a bandage. It is also important not to forget about naturalness, because in a real swan, closer to the body, the neck begins to thicken. You will have to do the same.

Stage 6.

Stage 7.

The swan figurine is ready. Now you need to give her time to dry completely, taking her to a place protected from rain and sunlight. Once the product is dry, it can be sanded with a fine mesh to create a beautiful, even surface. Before painting, the putty is primed. What paint is better to paint a swan? Any base can be suitable for this, but it is more practical to use enamel paint. It is convenient for her to draw eyes, beak and feathers. After the whole structure is opened with varnish to consolidate the result.

Swans from plastic bottles for the garden with your own hands- original, beautiful decor that will delight your eye and decorate landscape plot. We hope that our tips will help transform yours by adding your own creation to it.

Any summer resident dreams that his site was the most spectacular among the rest. As soon as they do not decorate adjoining territory, but the most common way is to create figures from plastic bottles due to the ease of installation and the availability of material. Birds and animals are most often performed. Today we will talk about the creation of a noble swan bird with graceful outlines from plastic bottles. Such a craft will become the highlight of the whole garden and will definitely not go unnoticed.

Varieties of swans from bottles

At the moment, from plastic bottles, you can create any configuration and design of a swan. Moreover, it can be not only decoration, but also a functional addition to the site, for example, a planter. The final result depends only on the imagination of the master and the materials and techniques used in the process of work. Among the variety of options for creating from plastic bottles, you can easily choose the one that is most suitable for the time spent, materials and just the algorithm of actions for a particular master.

Planter in the shape of a swan

To complete such a craft, you will need one bottle of 5 liters and a sufficient number of small plastic bottles. It is best to take those in which milk was bought, since they are white, which will be relevant for a swan, and subsequently it will not be necessary to color the material. In addition, you will need a metal rod to create a long swan neck, a metal mesh to decorate the base of the wings, adhesive tape, thin wire and fishing line that serve as connecting materials.

We carry out blanks

The preparatory step before creating a swan is to clean plastic bottles from dirt, labels and glue. Next, markings are made on each small bottle.

So, for starters, a line is drawn 2 cm below the neck of the bottle. The lower dotted line should be 1 cm above the relief part of the bottle. They are connected by a strictly perpendicular line. It is necessary to mark and cut the details as evenly as possible.

After cutting off the neck from white bottles, you do not need to throw away these parts, they will serve as a decoration for the swan's neck. The lower part under the neck is cut into 6 rounded parts. You can hold them over a burning candle for a bit to get a more realistic look. At the base of the finished petals, 3 paired holes are made.

The head of the swan is a 0.5 liter bottle. It is performed according to the following algorithm:

1. Removing the neck plug.
2. Making an incision along the seam in a cone-shaped section.
3. Cutting lines with a gap of 0.5 cm.
4. Gluing a clothespin to play the role of a beak.
5. Cutting a fringe on a bottle from the side of the bottom.

The basis of the body of the swan is a bottle of 5 liters. Holes are made on it from below and from above to attach the neck.

Construction assembly

After all the components of the future swan are completed, you can begin to assemble it. First you need to fix the eyes on the head of the swan. It is best to do this not with glue, since with constant influence environment they will quickly fall off, and fasten the buttons with wire.

The blank of the swan's beak must be wrapped with tape so that the halves of the clothespin do not fall apart. From above, the design is decorated with a red cloth or foil.

Next, you need to fix the neck rod in the head of the future swan with wire, and fill the bottle itself with padding polyester. After that, you can string the bottle necks created earlier on the rod. The fringe on the head is fixed with fishing line to cover the beginning of the swan's neck.

The rod from the swan's neck goes through a large plastic bottle and out. The whole body of the bird is shaped with nylon threads or a nylon stocking is pulled over it. Strong synthetic threads, starting from the tail, mount parts of the plumage, stacking them on top of each other to hide the fixation points.

As a result, a chic swan will turn out from the bottles, which, in addition to external beauty, will also serve as a spectacular container for planting flowers. You can put such a craft anywhere on the site, but the swan will most organically fit into the territory near an artificial reservoir, if one is present on the site. And if it is not there, then from the same plastic bottles it will not take long to simulate a pond.

Swan from bottles and tires

If there is one or more tires available in the summer cottage or in the garage, it is quite possible to build a swan from them. The combination of plastic bottles and rubber allows you to get not only beautiful, but also resistant to external influences and turning over crafts for the garden.

Execution Technology

To create the body of a swan, a tire with a diameter of approximately 50 - 55 cm is taken. So, the formation of the body of the future swan follows the following technology:

The head of the future swan is made from a piece of foam plastic with dimensions of 20 * 12 * 10 cm in this way:

For plumage, birds will be needed

• plastic bottles preferred white color;
• pliers and a sharp knife;
• construction mesh;
• cutters and wire.

When calculating the number of bottles, one should take into account the fact that one container will become the basis for 5 - 6 feathers. Petal-like elements of the same size are cut out of it, on which 4 holes are created for fixing on the grid. For more believability, the edges of each petal can be slightly melted or just cut a fringe on them.

Important! The mesh is pre-coated with an anti-corrosion compound to extend the life of the finished swan.

All swan feathers must be mounted on a piece of mesh, shaped like a wing, with overlapping wire so as to cover the joints. Even on the inside of the wing, it is necessary to create several rows of feathers in order to finished construction grid was not visible. The tail of the swan is done in the same way.

After preparatory work proceed to the direct assembly of the structure. The connection of the neck with the body of the swan is made by screwing in the bolts. It is important to bend the end of the metal rod from the neck so as to fix it in the ground. The wings must be fastened together with wire and fixed with a rod. After that, the tail of the swan is installed.

Putty and bottle figure

An interesting craft option for suburban area- a swan from a five-liter bottle, decorated in the form of a sculpture. This is a unique creation that allows the fantasy to run wild. Such a swan will decorate the veranda, terrace and even look good just in the clearing. Among other things, it is very practical, since inside it is possible to create a small flower garden. If you decorate it with white flowers, you can achieve the effect of bird plumage.

The main stages of making a swan:

After completing the figure of a swan, it is necessary to wait for it to dry completely, carefully process it with sandpaper, and then paint it in the likeness of a living bird. The swan is a symbol of fidelity, so it is best to pair it up right away. Such figures will enliven and diversify the landscape of the suburban area. Into the recess from plastic bottle you can plant marigolds, which will complete the composition.

Spectacular film swan

From a plastic film and an ordinary five-liter bottle, it is easy to assemble a real proud swan, which no guest will pass by without surprise. Consider the manufacturing technology step by step:

1. We make 2 holes in the bottle and stretch a thick wire into them that can keep its shape. It will become the frame of the neck and tail of the future bird.
2. To give a neat and smooth outline, the bottle is slightly crushed in front and on top. The resulting form is fixed with adhesive tape.
3. Ribbons about 7 cm wide are cut from isolon. The entire swan blank is wrapped around them and fixed with adhesive tape.

   Important! The head is also formed from isolon, but with more layers.

4. A plastic film is being prepared to create the plumage of a swan. To do this, strips of ribbon are folded into several layers and cut so that a fringe is obtained. 17
5. The whole bird is wrapped with such blanks, fixing the film with narrow tape. Each subsequent revolution is shifted by 2 cm relative to the previous one.
6. The head is supplied with button eyes. They are easy to just sew on.
7. The beak can be made from a red clothespin or marker. In the second case, it is necessary to make several cuts on it so that the wide part of the beak can be formed. After that, the marker is mounted on the wire.

Such an unusual swan will bring originality to the landscape of any site, and with any breath of wind, its plumage will sway easily, which is also very unusual.

Conclusion

The swan on the site is lovely decoration, which will bring diversity to the landscape of an ordinary summer cottage. Thanks to the creation of figurines of this bird from plastic bottles, you can not only take time, develop your imagination, get a spectacular decoration, but also get rid of unnecessary containers. Thanks to the presented master classes, everyone will be able to choose the equipment for themselves and update their site.

Swan made from a wheel and plastic bottles.

Swan made of tires and plastic bottles.
Greetings, friends, we continue to get acquainted with the works of Alena Zinovieva. Today I will show you Master Class for manufacturing swan made from tires and plastic bottles. On my own behalf, I want to note that over the years I have met many swans made from tires. But this is how I managed to make Alena I met for the first time. I hope you will like it too and you decide to decorate your site with such a beautiful swan.
How to make a crane from a plastic bottle.

For its manufacture we need: 1. Old tire.
2. Plastic bottles 70 pcs per pair.
3. Metal mesh.
4. Hose from a vacuum cleaner.
5. Wire for the neck.
6. Styrofoam.
We cut off the inner rings from the tire, cut out a triangle-future tail with a jigsaw.

We connect the edges with bolts, for convenience, cutting the tire in front.

We fasten the base for the neck to the tire with wire,
leaving a little below to then insert into the ground.

Front view.

We collect the wing from feathers cut from liter white bottles (1 bottle-6 feathers).
We fasten on metal mesh wire.

Inside the wing, along the upper edge, lay out a couple of rows of feathers,
to in finished product grid was not visible.

Finished wing.

Styrofoam head. It is put on the base wire,
the hose is fixed with self-tapping screws (advice - dip the self-tapping screw in the "Titanium" glue)

A neck hose from a vacuum cleaner.

We paint the bird.

The wings are screwed to the tire with screws,
as an option, pull together with wire through the tire.
How to make a stork from plastic bottles.

Frog, cow and crow

Summer, cottage, warmth, I want to live and create. I think you have familiar motorists, and if not, then you can go to any garage nearby and ask them for a very valuable canister, as it turned out this summer, from under any liquid. I think they don't need it, but we need a lot of creative material. I found two like this.

In addition, we will need our favorite mayonnaise jars (you can replace them with plastic bottles). It's very simple to take a jar and cut off the top. We cut out everything we want from old canisters, connect all the parts, paint, and here it is the result. From the remaining handle from the canister come out excellent savochki.





I hope you liked something and you wanted to make the same for yourself. I wish you creative success.

The swan is a beautiful bird that adorns any pond. But not everyone can afford to buy and care for real swans. But you can make your own, artificial swan from improvised items.

Such a swan can be used to decorate a garden or playground.

You can also make a swan, in which you can pour earth and plant flowers. One way or another, both you and the children will enjoy the aesthetic pleasure of such crafts.

How to make a swan out of a tire





1. Prepare old tires, preferably "bald", and mark the cut lines with chalk.

2. Start cutting along the lines, then bend it so that you get wings.









3. In order for the head and neck with the breast of the swans to keep their shape, it is advisable to use a stainless steel plate, which must be bent so as to give the shape of the head, neck and breast.









4. After that, you need to screw the plate to the rubber using inconspicuous small screws.

5. Also cut out the eyes from the rubber and, using the same screws, attach them to the swan's head. And after that cover our swans twice with white water-based paint, just make the noses red.









6. It remains only to fix the swan in the halves of the covers, pre-painted in the color of the water (blue, light blue, green), and your swan swims in the pond.

How to make a swan from a wheel









This is another option for making a do-it-yourself swan from a tire. To make it, prepare, as always, an old wheel, chalk, a sharp knife (just in case, also prepare a hacksaw or jigsaw) and paint.

1. Using chalk, draw on both sides of the wheel all the details of the future swan, i.e. head, tail, wings, neck, beak.

2. Start with a sharp knife to cut out all the details along the contour lines.

* In case some details do not lend themselves, you can use a hacksaw or a jigsaw.

3. Bend back the wings and neck. If the neck is difficult to bend, plywood will help you with which you can fix it.

4. It remains to paint the swan.

How to make a swan (video)

Watch the video tutorial on how to make a tire swan if you want to understand some of the details. In this lesson, a jigsaw was used.






How to make a swan out of a tire









1. The first thing to do is to mark with chalk the places on the tire that you will cut. The images show these lines.

* If your knife is sharp enough, then everything will take you no more than 20 minutes.

* It is worth noting that it is very difficult to cut thick rubber, so use a sharp knife, which is periodically moistened with soapy water.









2. The hardest part of the tire must be knocked out with a chisel or grinder. This part will serve as the head and tail of your "swan". The whole thing will take no more than five minutes.









3. It's time to flip the tire.

4. It is advisable to properly process the head and tail of the rubber swan, as you can get scratched due to uneven edges.

5. It remains only to paint the swan - you can use white or a very unusual and beautiful bronze color.

How to make a swan from modules







Crafts from plastic bottles. Swan.









No need to get rid of plastic bottles if they have already been used for their intended purpose. There are many crafts that you can make from them.

For example, there are several ways to make a beautiful swan for the garden. Moreover, such a swan will not only decorate your garden, but will also benefit.

You will need:

Plastic bottle 5 l

Milk bottles 300 g

Hose with hard wire

Wire

Scissors

1. Using a marker, mark lines on a 5-liter plastic bottle, along which you will cut next.









2. Cut off first upper part bottles and leave a neck that you need to secure the swan's neck in the hole.









3. For the swan neck skeleton, use a stiff wire hose. Insert it into the bottle through the neck and fasten the neck to the lower body with a wire. You have a swan frame ready.











4. We prepare feathers for a bird. Take a white plastic bottle (usually used for milk) and cut off the neck and bottom.









Start cutting the "feathers" - their width and shape depend only on your imagination.









It is desirable to cut the edges of the "feathers" with a fringe to achieve an even more realistic effect.









From the outside, heat each candle feather.









5. Start collecting two feathers and fix with wire.









6. For the bird's neck, use bottomless bottles. Depending on their number, you can choose the length of the neck. In this example, 16 bottles of 300g were used.

The part near the beak was made from the top of a bottle without a neck.

7. Where the beak is located, the hose ends and to fix the structure, you need to make holes on both sides in the bottle and in the hose. Next secure it with wire.









8. Close the lid and take a chemical cap to prepare the base of the beak. This cap needs to be cut in half, similar to the letter M.

9. Take another such cover and insert a beak into it - there is a groove inside, so that everything comes out exactly.

10. Glue the first and second cover.









11. Paint the beak, and place your favorite plants in the flower bed.

How to make a swan out of plastic bottles









This is not just a swan - this is a swan princess that will decorate any garden. It should be noted right away that the assembly of this swan is a laborious and rather lengthy process, so be patient and let's get started.

You can call for help in creating crafts from one or more people to speed up the process.

Prepare:

Plastic bottles

Thick copper wire (if you have thin wire, fold it in half so it doesn't break)

Stationery knife

Pliers

White and yellow paint (can be regular or in aerosols)

1. A plastic bottle swan should be started from the head and neck. Then these parts of the swan pass into the body. First, cut a plastic bottle under the head.









2. Cut off the parts of the neck of the craft. It is advisable to make 18 similar blanks in advance to get a neck.









3. Use an awl to pierce each piece.









4. Prepare the wire and thread it into the holes of the blanks, gradually stringing them to form a neck (you need to thread the bottom to the head). Attach your wire to the tip of the beak.









5. When you have collected all the blanks for the wire (1 blank for the head and 18 for the neck), start assembling the torso. Prepare 4 bottles and cut them as shown in the image:









6. In the same way, start stringing blanks on the wire. Insert a whole bottle into the last blank.

7. Fasten the other end of the wire.

8. To make the neck of a swan stronger, you must first give it the desired shape. To do this, simply adjust the depth of entry of one workpiece into another.

Use wire to secure all the parts of the swan together.

Start piercing holes in the bottles that make up the neck so that the wire runs parallel to the floor (you need to do this on the floor and start preferably from the tail).









You should have a kind of "zigzag" of wire - it should "enter" and "exit" the neck where the two blanks enter each other.

9. Draw the topmost end of the wire where the crown is attached.









10. From a plastic bottle, cut out a crown for the swan princess.

11. Take the crown and fasten it to your swan's head. To do this, you need to make 2 holes in the neck of the crown and thread the wire from the neck into them. Next, you need to wrap the wire around the neck and clamp it with pliers.









12. It's time to assemble the body. The first thing to do is the stomach, which has two "sticks" and each of them is made up by connecting 4 large blanks (point 4) and 1 whole plastic bottle.









You need to "flash" these "sticks" using wire. You need to do this in a zigzag, parallel to the floor. It is necessary to get a rigid foundation for the swan.

13. We continue to make the body, namely its next row. The middle will be occupied by the neck of a swan, which means that you will need the help of another person - while you are "flashing" the second row, your assistant needs to keep your neck constantly in an upright position.









Still, to begin with, you need to prepare 2 "sticks", each assembled from five large blanks and one whole bottle (for the tail). After that, all 3 blanks must be fastened with wire, setting the neck between two "sticks".









14. Pay great attention to fastening the curve of the neck in the front.









15. We are preparing the third row of the body. Start collecting another "stick" - use 4 large blanks and 1 whole bottle for the tail.











Thread your workpieces tightly into one another, and pour water into an untouched bottle to balance the neck and tail of the craft.

It should be noted that the stick does not need to be stitched separately. All you need to do is put it on top of the neck from the side of the body and attach it with wire to the side "sticks" of the 2nd row of the swan body.

16. It's time to make wings for your swan. To do this, you need to collect 2 "sticks", each of which contains 4 large blanks and one whole bottle. Bend the blanks as shown in the image and zigzag them again with wire.









To make the base of the wings, you need to make 2 short "sticks", each of which consists of one whole bottle and one large blank.

17. Start attaching the bases of the wings to the body of the swan. The image shows a top view, and with right side bird's tail. To attach everything, use a wire that needs to be threaded through the bases of the wings and fastened to the already installed swan parts.







22. It's time to paint. To do this, you can use both spray paint and regular paint (but it will take more time). If you decide to use an aerosol, then you need to paint outdoors, and not indoors.









How to make a swan with your own hands









In this master class, you will learn how to make a beautiful flower bed out of the swan you made earlier.

You will need:

Plastic bottles

Plastic bags (preferably tight, for example, from under washing powder or dry pet food)

stapler

Saw or knife

Pliers

Scissors

Soil (preferably special ready-made soil from bags).

1. First you need to firmly fix the swan in a place specially prepared for it. To do this, you need to dig a shallow hole.









To keep the swan straight, on both sides of it you need to hammer 2 wooden pegs, in the upper part of which you need to make small incisions.

Pull the wire through the notches, which will help the craft stay flat.









The wire is threaded, pulled together and fixed under the curved parts of the wings.

2. Prepare one tight bag and cut it so that you get a large rectangle.









Use this plastic "blanket" to cover the inside between the wings.

* The edges of your bag should protrude slightly from the wings.

3. You have got a kind of pot in which you need to pour earth for flowers.









4. Use a stapler to secure the front and back of the flower bed.









* If desired, you can cut off the excess edges of the polyethylene.









5. Now it remains only to plant something in the finished flower bed.

How to make a paper swan






How to make an origami swan

The graceful bird has always fascinated with its grace. It became possible to place a symbol of fidelity in your garden, having everyone at hand available material. Information on how to make a swan from plastic bottles, offered in three options, will allow everyone to choose the most appropriate way.

Swan planters from bottles

Differ in a different category of complexity. A step-by-step guide will help even a novice master to cope with the task of decorating a swan. The main thing is to be patient. One bottle of 5 liters and a lot of white plastic containers with a volume of 1 liter are the main material of a spectacular craft. You will also need:

• metal rod for the swan's neck;
• fishing line, adhesive tape and thin wire for connecting individual parts;
• metal mesh serving as the base of the wings.

Preparation of individual parts

Making a swan precedes the preparatory stage. Work begins with the cleaning of plastic bottles from the remnants of labels and glue. On a clean container, markings are made according to the photo. The upper line is drawn 2 cm below the neck, the lower line is 1 cm higher than the corrugated part of the plastic bottle. There is a perpendicular line between them. The cut is made as straight as possible.

For the neck, parts from plastic bottles with a neck are cut into 6 parts, cylindrical elements are divided into 8 fragments.

Attention! All corners on the blanks are rounded, 3 paired holes are formed at the base of the petals.

A neat swan head is obtained from a 0.5 liter plastic bottle as follows:

• the neck with the cork is removed;
• on a cone-shaped section, an incision is made along the seam;
• all other incision lines go with a gap of 0.5 cm;
• the ends of the clothespin, which will play the role of a swan's beak, are melted over the fire;
• holes are pierced on them with an awl, holes are formed at a similar distance in a plastic bottle.

The basis of the swan's body is a 5-liter container, on the bottom and lid of which holes are made to fix the neck. The opening on the side should allow the hand to easily get inside the container.

Assembly process

When the individual elements of the swan are decorated, you can proceed to the assembly of parts:

The result of a painstaking process is spectacular swan from plastic bottles, similar to the photo below:

Combination with tire

There is another interesting and affordable option for making a bird with a majestic neck bend.

Frame

According to the proposed master class, a swan made of plastic bottles will turn out to be no less bewitching. The main difference is that the function of the trunk is performed by a tire with a diameter of 50-55 cm.

Hull shaping:

• The cover is cut in half. Work carefully so as not to injure yourself with the cord.
• One part is shortened by 10 cm.
• Both parts are connected in the shape of an egg about 45 cm wide and securely fixed.

The result will be the workpiece shown in the photo:

Head

Making a swan head:

• The basis of the part is polystyrene 20x12x10 cm.
• The head with the beak, after cutting out, is carefully polished with sandpaper.
• A 5 cm deepening is prepared at the back of the head to fix the neck.
• The swan's head is evenly treated with putty.
• After the solution has dried, the surface is polished with paper of a finer grain size.
• The workpiece is coated with white, black and blue paint. An example is the following photo:

Neck

The process of creating a bird neck based on plastic bottles:

• A rod about 2 m long is given the desired shape.
  Advice! It is better to refuse a steel part, it is too difficult to bend and can burst.
• Corrugations will need about 80 cm. When using old material, it is thoroughly cleaned of contaminants.
• One edge of the corrugation is made with cuts for mounting the swan's head.
• The swan's neck is fixed to the body and head with self-tapping screws.

Plumage

For the plumage of a swan you will need:

• plastic white bottles - about 40 pieces;
• construction mesh;
• pliers and knife;
• wire, cutters.

Painting the mesh with white paint for outdoor use will help to avoid corrosive processes. One plastic bottle serves as the basis for 5-6 swan feathers. On each blank from a plastic bottle, 4 holes for the wire are prepared. Optimal use copper material which bends easily. Feathers are connected with overlapping wire to hide the connection areas. The process of formation of the wings and tail of the swan is identical, the difference lies only in the outlines of the grid.

Mounting and installation

When all the parts from the tire and plastic bottles are ready, they begin to assemble the swan. The site where it is planned to locate decorative figure, is made out with bricks, a board or a car tire. This will be a kind of podium.

The connection of the neck with the body is carried out with self-tapping screws. The end of the rod is bent in such a way that it is possible to fix it in the ground. The wings are fastened together with wire, clamped at the back with a rod. Next, the tail of the swan is fixed. The head, made from a plastic bottle, is screwed to the corrugation with screws. An elegant bird made of plastic bottles with your own hands will become a worthy decoration of the site.

Grace in the garden

Another craft option based on a large plastic bottle also has practicality, thanks to the possibility of placing flowers inside.

Basic manufacturing steps:

The swan is a symbol of fidelity, so it would be logical to make a beautiful bird a couple. This composition will not leave anyone indifferent.

The proposed workshops will help transform landscape design with minimal financial expenses. The main cost is your time and patience. Good luck with your work!

• Birds from plastic bottles
• Recreation area in the country
• How to make a palm tree from plastic bottles
• Garage design on site