arches 

Properly glue wide non-woven wallpaper. How to glue non-woven wallpaper? At what temperature to glue the wallpaper

Due to the special structure of non-woven wallpaper, consisting of cellulose fibers impregnated with a polymer binder, they have good performance characteristics. Also, the sheets have a smaller mass and a greater width of 106 cm, for this reason they are considered a universal coating and are in high demand. The process itself, with the exception of minor nuances, is not much different from the technology for gluing other types of tapestries, so you can glue non-woven wallpaper yourself.

Characteristics of wallpaper with non-woven base

Flizelin does not require special care, is not saturated with moisture, therefore, to keep the finished coating clean, it is enough to wipe it with a soapy solution. Unlike paper counterparts, non-woven wallpaper does not need to be impregnated with glue, for this reason it is applied exclusively to the wall, which saves a lot of time.

A non-woven fabric is denser than paper material, therefore it hides minor surface defects well. And the presence of a high-quality edge allows you to glue the sheets close to each other, the joint in this case turns out to be inconspicuous, barely noticeable, and the entire surface looks like a single whole.

Preparing the necessary tools and glue

Before starting work, prepare tools and materials. Would need:

  • tape measure of sufficient length;
  • level;
  • pencil;
  • spatula made of plastic, preferably with a soft edge;
  • narrow metal spatula;
  • roller with a long pile nozzle;
  • brush for smoothing sheets;
  • sharp knife for cutting blanks;
  • special mesh to remove excess glue;
  • two buckets, one for the adhesive solution, the other for clean water;
  • soft foam sponge.

The quality and reliability of the coating directly depends on the characteristics of the adhesive composition, therefore, pasting with non-woven wallpaper should be carried out on a specialized adhesive, which you can prepare yourself, following the manufacturer's instructions.

To do this, pour into a container not a large number of water, glue powder is gradually added to it, constantly mixing the contents. The resulting mixture is left to infuse for a while, then shaken again and filtered to remove possible lumps. Glue is ready.

Cleaning walls and applying landmarks

Getting started, be sure to inspect the walls, trying to identify and eliminate any defects. An excellent basis for sticking non-woven wallpaper is: wooden and concrete base, drywall, plaster, others similar materials. Since the canvases are thin, close attention is paid to the tone of the surface - it must be uniform.

Wallpapering starts only when the floor and ceiling are already done. The preparation of the walls begins with the removal of old wallpaper, paint and any dirt. Also eliminate any defects in the form of recesses and bulges. Having puttied the surfaces, they are covered with a primer, which will increase the adhesion of the glued material. But you can start gluing only after the primer has dried.

Any metal parts, protrusions must cover oil paint. Painting will protect the metal from corrosion and prevent the formation of rust spots.

non-woven meter wallpaper, like vinyl, have smooth edges, which allows you to glue the sheets end-to-end. Visually, the seam between adjacent panels is almost invisible, and they look like one whole.

Since the wallpaper is wide, you should start gluing from the corner of the room. Stepping back from him one meter, with the help of building level or a plumb line draw a strictly vertical line. The applied markup will serve as a guide for the first sheet. Moving along the wall in increments of at least a meter, the remaining lines are applied. This will allow you to make a certain margin, which will help create an even joint in the corners.

Marking and cutting wallpaper

After marking the walls, you can start cutting sheets. Canvases should be prepared immediately on all surfaces, which will allow them to be selected depending on the pattern and properly distributed. Whole ones are best glued in open areas and in corners, and cut ones are used for gluing hidden places located behind radiators and furniture. If the drawing is not complicated, then difficulties usually do not arise.

It is very important to make sure that the height of the walls is the same throughout the room, for which they are measured in several places, only then they start cutting the wallpaper to the required size.

The situation is more complicated if canvases with a large pattern, since in the process of fitting its parts are more difficult to combine. To do this, each subsequent sheet will have to be shifted up or down, and in case of an error, glue a piece of wallpaper.

By adjusting the canvases according to the pattern, they are placed on a clean, flat surface or on the floor. It is pre-washed and allowed to dry, in extreme cases, a piece of plastic wrap can be laid on the floor.

The roll is rolled out face down and, having measured the required distance, a notch is made with a knife. The wallpaper is bent along the marked mark so that the edges of the main sheet and the bent part coincide with each other. The fabric is pressed down and cut along the fold.

Before cutting off the next sheet, check the fit of the drawings, aligning them with any visible detail, and, if necessary, fold two edges already. Then they are pressed and cut along the bend. To reduce material consumption, the wallpaper roll should be rolled out sequentially, starting from one side. From the remaining canvases, the required number of blanks is cut in the same way for the entire room.

Main stages of work

Having completed preparatory work, start gluing. The technology itself is simple and will consist of several stages, but first you should familiarize yourself with the factory instructions that are attached to the wallpaper and may contain specific comments and requirements from manufacturers.

After that, they begin to apply the adhesive mixture to the surface of the wall, and only in exceptional cases cover the non-woven base with it. The glue is applied in an even layer using a roller, trying to prevent gaps, for a better setting of the edges of the wallpaper with the wall, a slightly larger width is smeared than the size of the sheet. For gluing, it is recommended to take a special glue designed to work with non-woven wallpaper. It is undesirable to use any other, preserved from the last repair.

Next, the first sheet is glued, the final result depends on how correctly and evenly it will be located, since the first canvas serves as a guideline for comparing the position of subsequent blanks. Having fixed it from above, the sheet is gradually rolled out downwards, evenly smoothing with a spatula, directing movements to the sides and squeezing out excess glue. But if the wallpaper has a deep texture, then all actions are performed with a wallpaper roller, pressing it against the sheet without effort.

The glue that has come out on the sides is removed immediately, wiping the joints with a damp sponge, rag. Since after drying, traces of the adhesive solution may stand out against the general background. The rest of the canvas in the lower part is cut off, stepping back from the floor at a distance less than the width of the plinth. After gluing all the blanks, it is used to create the final edging and cover possible defects. The wallpaper is cut by pressing it into a corner with a spatula and moving it along the plane with a sharp knife.

The next sheet is rolled out along the wall strictly vertically, fitting end-to-end to the first and at the same time combining the details of the pattern. Excess glue is removed in the opposite direction from the wallpaper and, having smoothed the seam with a roller, cut off the excess in the upper and lower parts of the canvas.

The corners are glued in the same way, but if necessary, the sheets on the sides are cut at the same time. First, the upper strip is removed, then the lower one, and for greater reliability of the connection, by unscrewing the edges of the canvases, the joint is re-coated with glue. Next, press to the corner and wipe with a damp sponge.

After gluing the last sheet, it remains to check the quality of the work performed and, if necessary, glue or roll the joints that do not inspire confidence with a roller again. Finally, the finish is left to dry with doors and windows closed.

If during the repair you want to update the walls with a high-quality and beautiful coating, construction counters will definitely offer non-woven wallpaper. The material has high performance characteristics and a lot of advantages, looks great and is unpretentious in care.

Non-woven wallpaper - durable and elegant coating

The main place in the composition of this rolled web is occupied by cellulose fibers, which are natural components. The rolls themselves are divided into two types:

  1. non-woven, created from several layers of 100% non-woven, give texture to the topmost;
  2. on a non-woven basis - they include two layers, one of them is pressed from cellulose fibers, and various components (vinyl, paper, textiles, etc.) are applied to the second, which form a relief pattern.

The advantage and characteristics of non-woven wallpaper for walls

Due to its positive factors and strength characteristics, this coating has gained popularity among buyers. Main positive traits non-woven fabrics are given below:

  • elimination of small irregularities due to its density and embossed texture. It follows that there is no need for a perfectly smooth base surface;
  • the existing versatility allows the use of the material on any surface;
  • vapor permeability / fire resistance;
  • safety for health, since the canvas is non-toxic;
  • suitable for painting;
  • good moisture resistance, which makes it possible to use them in the bathroom and in the kitchen;
  • resistance to external influences guarantees durability.

How to stick non-woven wallpaper on the wall


Before you start attaching the canvas, you should prepare the base surface - clean it with fine-grained sandpaper from the old coating and glue.

Non-woven sheets have translucent properties. The base must be washed from inscriptions and various kinds of pollution.

Then do the following:

  1. Remove switches and sockets.
  2. Prime the wall to prevent mold.
  3. Let dry.
  4. Eliminate large chips and errors with plaster putty.
  5. After the putty has dried (on average in a day), proceed with the preparation of the adhesive composition in accordance with the requirements.
  6. Measure the required heights, add a margin of 10 cm and cut the wallpaper strips.
  7. Apply the adhesive to the wall in a thick but even layer. Necessarily! Glue is applied exclusively to the walls. They do not need to cover the canvas.

If you have a picture before cropping, be sure to perform a selection so that the result looks like a single holistic picture.

Only after the performed operations are allowed to proceed to direct gluing. holding on to upper part cut strip, you need to attach it to the wall in such a way as to fix it exactly relative to the surface. Having fixed the sheet from above, you need to move to its lower part. After fixing, smooth the material by moving the roller or brush from the center to the edge. Remove excess glue with a rag. When applying the following sheets, it is worth smoothing the joint area properly.

What glue to glue non-woven wallpaper


Glue for this type of material is used in a special, thick consistency, since the canvas has a considerable weight. The adhesive composition is gradually poured into a container with water, while constantly stirring the resulting solution. After thorough mixing, let the glue stand until it swells.

Excess adhesive solution can be left with a roller in a special plastic grid.

How to glue wide meter wallpaper

Rolls in most cases are presented with a width of one meter. This format saves time as the workflow is faster. In addition, the seams as a result of gluing will be two times less, unlike rolls with a width of 0.5 meters. The process of gluing sheets of meter width according to the technology does not differ from the standard one.

Pasting the walls with non-woven wallpaper in the corners

When gluing corner sections, you should follow some simple rules:

  • attach the canvas so that an overlap of 2 cm is formed on the adjacent wall;
  • do the same with the sheet on the adjacent wall;
  • gently press down on the material along the entire height of the corner until it touches the wall;
  • after drying, remove with a clerical knife the extra fragments protruding to the ceiling.

Joint Features


Each strip is glued together butt-to-butt. Sometimes you can find brands whose instructions require overlapping sheets. Butt joints are especially important to smooth with a roller.

What is important to remember

Before work, it is necessary to calculate the amount required finishing material: the sum of the areas of the walls and individual sections must match the area of ​​the roll multiplied by their number.
Throughout the entire working process and until the glue has completely dried, it is important to avoid drafts in the room.


It is worth gluing the wall with non-woven sheets from the corner section by the window.
Remove excess pieces of material with a clerical knife only after they have completely dried.
The non-woven coating for painting can be filled with color only after the glue has completely dried.

Do not rush to throw away the remnants of the finishing material. They can be useful for finishing small areas or correcting errors.

Adhere to the standard gluing technology, but be sure to first read the instructions on the roll. In case of differences, the latter shall be followed.

Caring for non-woven wallpaper

To keep clean and good appearance finishing coating, it is enough to periodically wipe it with a damp sponge and vacuum it.

Wall covering with non-woven material is reliability, style and comfort in the house. The cost of rolls of this series can hardly be called low, but the quality is worth it. The room will sparkle with notes of elegance and nobility.

Useful video

On sale there are two options for non-woven wallpaper: with a pattern and plain (suitable for painting). If you chose plain version, in the future you will be able to repaint the walls 8-12 times, which opens up incredible opportunities for regular renewal of repairs.

There is a feature of gluing non-woven wallpaper, which helped out a lot of inexperienced gluers: such wallpapers perfectly hide minor defects on the walls, if suddenly some bumps or cracks remain after all the alignments and polishing. It is thanks to this feature that gluing non-woven wallpaper is very easy and you can do it yourself without any problems, even without experience.

To purchase a sufficient amount of material, first make accurate calculations: measure the height and length separately for each wall. When counting the number of rolls, do not forget that you need to add 10-30 centimeters of stock to the resulting room height (the larger the pattern, the greater the increase). Before making a purchase, check that all rolls are from the same batch (the number is indicated on the package), so as not to find wallpapers of a different shade or even with different patterns at home.

Preparing the room for gluing non-woven wallpaper.

Before sticking non-woven wallpaper with your own hands, start by leveling the walls (be especially careful with the preparation if you have purchased wide wallpapers - the accuracy of the joints depends on your diligence during the preparatory work).

De-energize all sockets and switches and unscrew them, insulate the wires so that moisture does not penetrate into them during operation.

If possible, remove the plinth.

Scroll necessary tools.

Do not be stingy when purchasing non-woven wallpaper sticking tools: an ordinary knife or scissors can wrinkle or tear your new wallpaper, an old scratched spatula will not allow you to achieve a perfectly flat wall surface when leveling, and so on.

So, sticking non-woven wallpaper with your own hands requires the following items:

  • measuring tape, pencil;
  • level and plumb;
  • glue for a non-woven base, a container for glue and a roller;
  • polyethylene;
  • soft brush, plastic spatula;
  • edge roller.

The first step is to do the markings on the walls. Start from the corner (this is where the wallpaper will overlap). Measure one meter from the corner in both directions and draw vertical lines at this distance. From these lines, measure the width of your wallpaper and draw the following lines (they will indicate the junction). Continue marking on all walls.

Cover the floor with polyethylene and lay out the wallpaper front side way down. Measure the required length of the piece and fold the roll to get an even fold, cut off the wallpaper with a knife.

You can cut one piece at a time and glue it, or immediately prepare wallpaper for the whole room and roll it into not too tight rolls with a pattern (or color) inside.

Prepare a special glue and start applying it to the wall under the first cut. The rule for gluing non-woven wallpaper is very simple: start gluing from the ceiling and level it down, from the middle to the edge, using a brush (roller).

After the second piece is glued, use a roller to roll the seams.

Cut off the left stock of wallpaper from the bottom when the glue dries (do not forget that the wallpaper should be left with the expectation that the plinth will press them a little against the wall).

In preparation for wallpapering, pay special attention to the corners of the room. If use plastic corners, which are attached to wet putty, the result will be as accurate as possible.

Lubricate the corner with glue especially carefully, place the panels with an overlap (preferably no more than three centimeters).

How to glue non-woven wallpaper on the ceiling.

The first step is to prepare the surface: the ceiling must be clean and dry. It's good if you prime it before pasting.

Sticking non-woven wallpaper on the ceiling will not bring any unpleasant surprises: they will mask defects, they will not stretch, they will lie flat and without bubbles.

The technique of proper gluing to the ceiling is extremely simple. There is no need to adjust the canvas to the joint: they should be overlapped, and the excess edge should be cut off along the edge of the previous piece. So it will turn out to achieve a ceiling without seams.

Additional Information.

Before sticking non-woven wallpaper, watch the video. illustrative example will help you to do everything yourself correctly without bubbles and without seams - just follow the instructions of the master from the video of gluing walls with non-woven wallpaper.

No matter how good the wallpaper in a roll looks, their place is in the decoration of the room, so you still have to learn how to glue vinyl wallpaper on a non-woven base.

But you should not be afraid - working with these wallpapers is very simple. Despite the relatively high cost, these wallpapers are not only in stable demand, but are also rapidly gaining popularity.

There are many explanations for this - among them there is also a “novelty effect” - after all, the material appeared on the market relatively recently, but there are also objective factors - the quality of the coating is quite consistent with the price.

Pros and cons of a combination of vinyl plus interlining

Formally, these wallpapers do not consist of two, but of three layers - the non-woven base carries two layers - opaque, designed to hide the color unevenness of the walls and decorative vinyl ().

A huge variety of textures (including those imitating other materials) and patterns of such wallpapers allows you to implement quite bold design solutions.

One of the main advantages of using a non-woven base is considered to be the ease of gluing. Although from a practical point of view, wallpapers have many other advantages:

  • density and elasticity - allows the wallpaper to hide the defects in the relief of the walls, up to small cracks;
  • tensile strength;
  • resistance to abrasion and fading;
  • durability;
  • do not create problems during care - both dry and wet cleaning is acceptable;
  • high level of noise absorption;
  • no deformation - the wallpaper does not tend to stretch and shrink under the influence of moisture.

More often they are sold meter long - in this article.

Does this finish have any disadvantages? The main negative point is associated with the likelihood of obtaining a vapor-tight, and sometimes a surface of the walls that emit harmful substances.

However, this is the only disadvantage vinyl wallpaper can be practically reduced to nothing, not forgetting to regularly ventilate the room.

Preparation of materials and tools

So, a very pleasant stage - the choice and purchase of wallpaper is completed. What else is needed to realize the idea of ​​decorating a room?

First, you need a special glue. It is desirable that it be specifically for non-woven coatings (Flizelin Premium, Special Non-woven).

Second, care must be taken to right moment at hand were:

  • a paint roller and a flat brush (several brushes of different sizes are possible) - for applying glue;
  • rubber roller and wallpaper spatula - for smoothing wallpaper;
  • a bucket of at least 10 liters - for the preparation of an adhesive solution;
  • scissors and a construction knife;
  • plumb;
  • a few soft rags and sponges.

If the wallpaper has a regular pattern and there is a need to combine adjacent layers, then you can use a table for cutting right size, or you can cut and fit the wallpaper directly on the floor, of course, if you are sure that it is clean.

Pasting the room - the main stages

And now it's time to see in practice how easy it is to glue non-woven wallpaper (compared to paper, for example). Having decided to do it yourself, you should adhere to the algorithm:

Step 1 - preparing the walls for pasting

Not the most "clean", but an uncomplicated stage, including simple steps:

  • , plaster and wallpaper. You may need additional tools and tools: a drill, a hammer, special liquids for removing wallpaper;
  • removal of wall switches and sockets;
  • primer. Performs many tasks: leveling and lightening the color of the wall, giving strength to the putty (if it was applied), antifungal treatment of the wall. For non-woven wallpaper, you can use their “native” glue as a primer by preparing a solution of a weak consistency.

Leveling the cleaned surface. Non-woven wallpaper can smooth out bumps, but if there is a serious height difference of more than 1 cm,. If there are few irregularities, you can choose a more expensive and easy-to-use polymer putty;

Step 2 - marking the walls and cutting the wallpaper

It will be necessary to mark the walls in any case, but it is not always necessary to cut the wallpaper in advance:

  • marking on the wall of the starting point. Start pasting from the edge of the window opening, it is there that you should draw a vertical line with a plumb line;
  • wallpaper cutting. To do this, the height of the walls is measured, 10 cm of margin is added to the resulting value. It is this length that each cut piece of wallpaper should be;
  • pattern matching. If the details of the picture need to be combined, then first you need to cut a piece from one roll, and then pick up a “pair” from the other for it. This will avoid unnecessary material consumption.

Good news for those who have purchased wallpaper with a chaotic texture, without an ordered pattern: they can do without preliminary cutting at all, gluing the wallpaper directly from the roll - the strength and elasticity of this type of wallpaper create the conditions for this pasting method. A small overlap is made on the ceiling, which is later cut off with a knife, and the bottom of the wallpaper is cut under the plinth or along it.

Step 3 - Creating the Finish Coat

Directly work with wallpaper and glue:

  • adhesive preparation. The purchased ready-made mixture is diluted with water in accordance with the instructions. Important point- if you can’t exactly maintain the proportions, or you don’t want to, it’s preferable to make the solution thicker, i.e. put more powder, this will only improve the adhesive properties;
  • applying glue. The non-woven base of the wallpaper allows you to make this stage as simple as possible - the glue is simply applied to the wall with a roller, you do not need to cover the wallpaper with it;
  • gluing the first sheet. Regardless of whether the wallpaper is pasted in a separate piece or straight from the roll, you need to align the vertical edge of the wallpaper with the starting marking line. Start gluing from top to bottom, it is convenient to work with an assistant who will support a heavy canvas. Smooth with a roller or spatula from the center to the edge of the canvas, squeezing out air and excess glue, this will allow you to get a wall without bubbles;
  • combining and gluing the second and subsequent sheets. All sheets after the first one are glued end-to-end to the previous one (with an approximate overlap, a gap of up to 1 mm is possible, which will disappear when smoothed), overlap is not needed here. The joints are ironed with a roller, it is better to remove excess glue as quickly as possible with a damp cloth or sponge.

In the process of applying the adhesive, it is important not to rush, not to save the solution and cover with it only that section of the wall where the wallpaper will be pasted right now. If it didn’t work out exactly the first time, then the wallpaper can be removed and re-placed without compromising the quality of the resulting coating.

As you can see, gluing these wallpapers correctly is not difficult at all. However, in any room, in addition to smooth walls, there are such “obstacles” as corners, baseboards, radiators and electrical outlets.

A small brush can be used to coat hard-to-reach places with glue.

It is better to start wallpapering in the corners, having acquired at least some experience, but if you don’t have it, then at least carefully read the following recommendations:

  1. If the walls in the room are fairly even, and the corner is located so that it attracts attention, then the canvases are placed without overlap. To do this, the piece of wallpaper that is pasted first is wound around the corner with a margin of 2 cm. The next one is simply combined with it butt-to-butt.
  2. If the walls and corners do not allow the wallpaper to lay down flawlessly, you can glue the first layer in the same way as option 1. Since the corner is uneven, the overlap will be different. Where it is narrowest, you should step back from the edge of the wallpaper towards the corner by 1 cm. From this point, measure away from the corner a value equal to the width of the roll. Here draw a vertical line along the level, it will be the edge of the next layer of wallpaper. Thus, an overlap of about 1 cm is formed.
  3. You can glue wallpaper in the corners using such a common and quite effective method as a double cut (undercut) corner. To do this, the strips adjacent to the corner are glued alternately with a large overlap - up to 5 cm. The wallpaper is carefully “imprinted” into the corner. Then use a rigid profile (ruler or rail) located in the center of the corner in order to cut the wallpaper along the line. After trimming, the excess is removed, and the edges of the wallpaper are smeared with glue and ironed with a rubber roller.

But what about sockets? It is advisable to turn them off (as well as switches) for the time of pasting and remove them together with the boxes.

Their locations should be marked with a cross, cut along the same lines and bend the resulting corners inward. The boxes can be returned to their places once the glue has dried.

A wealth of textural and color solutions allows you to independently create a unique and integral design of the room, where the design of the walls will be in harmony with both the floor and ceiling finishes and the interior details.

Wallpapering is an essential part of any interior design. But every wallpaper is glued differently. After all, they differ not only visually, but also in the key material from which they are made. It is one thing to glue textile wallpaper, and another, for example, non-woven.

A professional master from a construction company works with wallpaper

But what exactly are the differences? How to glue non-woven wallpaper so that it comes out without problems with your own hands? In fact, everything is not so difficult, the main thing is just to understand general principle. So let's figure out exactly how to proceed if you prefer this type of wallpaper for yourself.

What is this wallpaper

In general, there are many types of wallpaper, for example, paper or fabric, but it is non-woven wallpaper that is now one of the most popular. They have excellent characteristics, they are easy to stick with your own hands, they look very interesting and are suitable for most rooms.

It is worth distinguishing between two types of such wallpaper. Some are purely non-woven, others have a purely non-woven base, and they have a vinyl coating. The second type is popular, as it copes better with moisture, so you can wash these wallpapers with your own hands. On the other hand, purely non-woven wallpapers are more breathable, which means there is less chance that a large amount of mold will form under them. However, it is necessary to choose, based on specific needs.


 Silver glitter wallpaper in the living room

Classic non-woven wallpapers are usually called, they often have some kind of texture without a color print, because they can be painted with your own hands in a convenient way, and the paint will fall on them much better than, for example, on textile ones. However, variations with prints are also available. In general, the choice of non-woven wallpaper is huge, so you can safely choose their variations for yourself. But no matter what you choose, it is very, very important to glue the wallpaper correctly.

Training

Before sticking non-woven wallpaper recently purchased from the store, it is necessary to carry out competent preparation. Without it, the effectiveness of gluing will not be as high, the wallpaper simply will not stick so well. So do not treat this negligently, do everything as it should, especially since it is quite easy to do it all with your own hands, but the result will please you for many years.


 We begin preparations for repairs, dismantling of old canvases

First, accurately measure the height and width on each side of the room. Estimate how many rolls you will need, but be sure to leave a few centimeters in reserve on each side. After that, you need to purchase the required amount of non-woven wallpaper. Please note that you need to pay attention to the specific lot number that is written on the roll. Even if the wallpaper is visually similar, if they have a different batch number, then the pattern may differ, as a result, there will be a slight imbalance in the room.


 Alignment of walls with plaster on lighthouses

Next, you need to align the walls with your own hands. This is especially important if the wallpaper is wide and does not respond well to bumps. You also need to unscrew all the sockets, they will greatly interfere. It is critically important to insulate the wires, otherwise liquid can get inside the boxes. All walls are primed and thoroughly dried. Moisture can not only create conditions for mold, but also simply prevent the wallpaper from sticking well. So it should be avoided.

Glue selection

Not any type of glue is suitable for non-woven wallpaper. However, textile and vinyl also require their mixture. So that different adhesives for different wallpapers are different. Be sure to consult a qualified seller in a specialized store, or at least carefully study the instructions for what this or that is intended.

The peculiarity of non-woven wallpaper is that they are saturated quickly, so you do not need to allocate some time for this, as is often the case when you take textile or vinyl wallpaper.

In general, individual mixtures may have different features and methods of application, so be sure to read the instructions after purchase, although it is clear that you do not want to do this at all.


 Good french wallpaper glue

Before directly sticking non-woven wallpaper, you need to understand what is the basic principle of applying glue when sticking them, and only then start gluing. The peculiarity here is that for ordinary wallpapers they smear the reverse side of the material, while for non-woven wallpapers it is necessary to smear only the wall. You need to smear lightly, evenly, you also need to press the material. The material is glued from the corner, from top to bottom. It is smoothed vertically with a wallpaper brush or roller.

Sticking sequence

In order for such wallpapers to be glued correctly, it is necessary to adhere to a clear sequence of actions.


 Non-woven wallpaper ready for gluing
  1. First you apply an adhesive solution to the wall, then take the first strip of wallpaper and adjust it in height. Using the method convenient for you, measure the verticality of the sticker. If the wallpaper does not match a little from above or below, then it's okay, this happens when you glue the wallpaper with your own hands. They can then just be trimmed a little.
  2. Next, the material is very carefully smoothed out so that there is no air left under it. You need to try to get rid of all the bubbles that can only form under the coating.
  3. Then take a wide spatula and a sharp knife. Using a spatula as a guide, it is necessary to cut off the excess wallpaper, and then glue them in those specific places where they are not glued well enough.

 With high-quality work done, the joints of the canvases are not visible

During the implementation of all this, do not forget that it is impossible to create excessive draft or heat in the room. The room should be slightly ventilated, but not so much that it could negatively affect how the wallpaper sticks to the wall. Before directly gluing non-woven wallpaper, deal with the temperature regime.

A few tips on how to glue non-woven wallpaper correctly so that the gluing is done at the highest possible level.


 Use of light wallpaper in the room
  • Don't forget to read the manufacturer's instructions for the specific wallpaper before installing the non-woven wallpaper. Although the non-woven solutions are quite similar, in some cases the gluing may differ slightly. For example, although it was previously written that it was enough to smear only the wall, some manufacturers recommend also smearing the wallpaper, as when you glue textile or vinyl options with your own hands.
  • Coat not only the surface of the wall where the wallpaper is directly glued, but also a slightly larger area. This will allow the edges to adhere better to the wall surface.
  • Wallpapers with a deep texture should be glued more carefully, it is best to press them with a wallpaper roller, which, moreover, should not be pressed too hard, otherwise the surface of the wallpaper can be deformed, then the roll will have to be changed.
  • When sticking wallpaper on the wall, excess glue may remain. You should not leave it, when it dries, it will not become 100% transparent, but leave unpleasant streaks. Take a damp sponge, and then gently wipe the place where the glue was applied. Try not to touch the wallpaper unnecessarily, do not moisten them. Although interlining does not wrinkle from a slight ingress of moisture, it is still better to protect it from water.

 Just finished wallpapering

It is not so difficult to figure out how to glue non-woven wallpaper. The main thing is to clearly understand whether these wallpapers are really optimal in your situation, and not, say, textile or paper ones. After all, if you make an incorrect decision, then in the future it will be much more difficult to change something.

Re-pasting wallpaper, cleaning the surface with your own hands and spending money again is something that would be good to avoid. So what do you do right choice immediately - and there will be no problems in the future, non-woven wallpaper is very resistant and durable, therefore it will delight you for an extremely long time.