wells after. How to pump a well for water after a winter downtime. Mistakes to Avoid

12.11.2019

With the help of a home well, you can solve the issue of autonomous water supply in the backyard. Works on its drilling are quite complex and require professional knowledge. They must be carried out by qualified professionals. After drilling is completed, the water in the well will be cloudy and with impurities. For proper operation, you need to understand how to pump the well after installing the system. The whole process can be done independently without the involvement of professionals.

Features of cleaning wells after drilling

Strainer and gravel filters are only capable of retaining large-diameter stones and sand. Fine particles infiltrate and lead to siltation of the well. They reduce height and reduce system performance. In order for the well to function properly, it must be pumped. For this purpose, a centrifugal submersible pump can be used. Vibration models are not the most the best choice for such work. They can't handle this load.

Do not use expensive equipment this stage, it is better to leave it until the water becomes clear. An important point correct installation pump is the correct height of its suspension. It must be fixed 80 cm above the line of the bottom of the well. This is done so that the sludge is brought out, and does not remain at the bottom.

Since the pump pumps dirty water, most likely it will periodically fail. In order for the equipment to continue to function, it is necessary to distill a certain volume of pure liquid through it. After flushing, the pump will be ready for operation again.

One of the most important conditions for pumping is the discharge of dirty water to the maximum distance. If it is not followed, the process can drag on indefinitely.

Together with submersible pump a special cord is usually supplied. For work, you need to use not it, but a strong metal cable or double Teflon wire. This is the only way to pull out the pump if it gets stuck in the silt or pipe.

Preventive methods to combat silting

In order for the well to work correctly, it is necessary to periodically pump it. It is especially important to turn on the pump for prevention in winter. At this time of the year, water intake is reduced and re-silting is possible. In summer, the purification process occurs naturally, as a lot of water is spent on irrigation. personal plot or filling tanks. If you follow preventive measures, you don’t have to monthly wonder how to pump a well.

If the well has not been used for a long time, more serious measures are required. A thick layer of silty and sandy deposits forms at the bottom, and resuscitation is carried out using high pressure to purify the water. We must try to use such a procedure as rarely as possible, since after it the mesh filter may break.

To resuscitate the well, pipes connected from several parts are lowered into it, through which, with the help of a fire hose or hose, under high pressure supply water. It washes away the silt layer and cleans the aquifer. If necessary, the length of the pipe can be increased. The process is considered completed when gravel particles from the bottom filter appear on the surface.

Well owners are often interested in the question of how long it takes to pump a well after drilling. In each case, the duration of the process depends on indicators such as the degree of water contamination and the pump power.

Common mistakes when purifying water

Incorrect operation can destroy a newly made well. To prevent this from happening, you need to avoid the most common mistakes in pumping water. These include:

Incorrect pump location. If it is too close to the bottom of the well or the top of the aquifer, pumping will not bring the expected results. The functionality of the pump will decrease and it may fail.
The pumped water is not discharged far enough from the edge of the well. Because of this, she will come back and the process will be delayed.
The pump is immersed on a cord. If it gets stuck, it will be very difficult to get it out.

When pumping, you need to monitor the level of the water column. This is very important point, which should not be overlooked. It is necessary to calculate how much water was pumped out, and 10% of this volume can be used per day. To do this, you need to know exactly how many cubes the pump processes per hour. If this condition is not observed, after some time after drilling, the vein will simply dry out and stop being replenished.

With the unreasonable use of natural channels, vacuum voids collapse and the well is destroyed. After that, only low-quality, dirty and muddy water will flow.

Cleansing Methods

In order to eliminate silting, first of all, it is necessary to determine the cause of this process. If coarse-grained sand appears in the water, which can be detected with the naked eye, it is already useless to try to pump the well. This is the first signal of the destruction of the well shaft.

It is possible to save a well only if during its drilling it was possible to replace the filter. This option is possible with a design in two columns. The filter is mounted inside the outer pipe. If during the dismantling process its destruction occurs, it will be cheaper to drill a new well.

Replacing the filter when used in a single pipe design is useless. After repair, re-silting will occur very quickly. In addition, the probability of successful dismantling is extremely low.

When a well is installed in limestone, by definition it cannot contain sand or silt. Therefore, if impurities were found in the water, only two options are possible. In the first case, the casing can be damaged at the level where there is a sand layer. Repair work restoration can cost more than drilling a new artesian well. In this case, it will be correct to determine the costs together with the company that performed the work.

The second option implies that the sand has flowed into the water along the walls from the upper aquifer. The reason for this process may be insufficient tightness of the upper soil levels or casing joints. The cost of repairs will depend on how deep the breakage is, the depth and diameter of the well.

Well drilling is carried out in several ways. These include:

Air purge. An airlift pumps air under high pressure into the well. This method is possible at a shallow depth of up to 30-40 meters.
Washing with water. The essence is the same as when blowing with air, only water is used. The pressure is less, so the risk of filter failure is lower.
Pumping the well with a special pump. Of the minuses, it is worth noting the frequent breakdown of equipment and the high risk of re-silting.

You can pump the well after drilling yourself, if you follow all the necessary conditions. If preventive maintenance is periodically performed, this will significantly increase the life of the well.

How to pump a well from clay worries many owners of their plots. This process requires sufficient skill and special knowledge, which entails the use of the experience of drilling specialists. This article gives brief information about doing the work yourself.

How a well is built and what it is

A well is a well-needle, this well is a small structure. Its diameter is at least 40 cm, and the depth can be from 20 m or more.

Note. Wells that are at depth are called artesian. They are located from 50 m.

Consider the types of structures:

Abyssinian are a pipe well. It is built to a depth of 12 meters. The most optimal is considered 8-10 m.
Such a well differs from the usual one in that the top water does not penetrate into the water source, which clogs the water and makes it unusable. There may be a deepening, at 15-35 m.
It all depends on the level at which the aquifer is located, the well looks like a pipe and that its walls do not crumble. interior decoration using asbestos or plastic pipes.
Quite often, clay or a special solution based on it is used in decoration. This makes it possible to use the well for a long time.
At the end of the pipe, which is used for the arrangement, there is a perforation that is wrapped in stainless steel. metal mesh. Such a filter is installed so that large particles of sand do not fall into the water. With small blockages, an automatic filter unit is able to cope.
This type of well is suitable for personal use in the country or any country house. big enough.

Advice. Quite often, wells are capable of silting up. If the well is not used regularly, it serves uninterruptedly for 5 years. If the well is operated regularly, then its service life increases to 15 years.

Over time, it silts up and it is necessary to clean and rinse it, see photo.

is a deeper structure. Its depth can reach 200 m. Basically, such deep wells are used for industrial purposes and their construction will require permission from the relevant authorities.
The service life of such a well is at least 50 years.
The water here is cleaner and does not require numerous filtration stations.

Well pumping, why is it necessary

The process of pumping a well, in which it is cleaned, must be performed immediately after drilling.

This is due to the fact that:

Almost always, the first water coming out of the pipe is cloudy, unsuitable for drinking and needs to be cleaned.
If no measures are taken, it will remain so dirty, and over time it will finally silt up and stop working.
The silting process never stops due to the fact that not only sand and pebbles are contained in the aquifer, but also a large number of tiny particles that the filter cannot catch.
They easily pass through the gravel and screen filters, and then settle to the bottom of the device. With a decrease in its depth, productivity greatly decreases.

from clay is performed immediately after drilling. At first, the water flows muddy, but gradually it brightens, is washed and reaches crystal clearness.
The time period for pumping the device may be different. If it is shallow, it may take from 12 hours. With sandy soil, the duration of the operation can take several weeks, and deep ones are sometimes cleaned for months, which is especially true for limestone or clay soil.
It is very difficult to pump out a well on clay. When drilling and cleaning under pressure of such a structure, a clay solution is formed. It seeps deep into the aquifers, it is very difficult to wash it out and it will take a long time. In this case, it will simply be necessary to pump out more than 500 cubic meters of water, which increases the duration of the process. The more water is pumped out, the more clay, sand and other small particles are removed. Coarse sand that has not passed through the filter settles to the bottom and creates an additional filter layer, as seen in the photo.

Tip: It is necessary to swing the well until the unit supplies clean water from it.

Why water with clay comes from an old well

From an old well that worked properly, water with clay can go for two reasons:

The casing was depressurized and clay began to flow into the well from the water-resistant layer.
After the filter broke through, all the turbidity that it had previously delayed began to go inside.

In both cases, it is necessary to make major repairs:

Pull the drill string out of the ground and eliminate the lack of tightness.
The filter can be repaired.

Correct buildup of the well

Instructions indicating how to rock a well on clay contain the following:

She swings equipment, the price of which is not high. It can be inexpensive domestic production. Such a unit is less sensitive to fine sand, but only one pump is not always enough for high-quality well cleaning and additional equipment has to be purchased.

The unit must be installed correctly. To do this, it is suspended in such a way that it does not reach the bottom of the well by about 50 centimeters. This is where the gravel filter level is most often located. In this case, silt that has not settled at the bottom is captured and then brought out.

Tip: You can increase the life of the pump by periodically “flushing” it by pumping a certain amount of clean water through the device.

Before flushing the well from clay, it is necessary to ensure the removal of dirty water as far as possible from the well in order to avoid its re-entry. Otherwise, the cleaning process will be endless.

The pump must be lowered into the well on a thin, durable cable. Only a strong cable will withstand lifting the pump if it suddenly gets stuck.

Well pumping methods

Cleaning a clogged well can be done in several ways:

Cleaning the well from clay with a pipe.
Using a vibratory pump with a nozzle.
The process is carried out simultaneously by two pumps. Usually it is deep and rotary.

Such methods can be used separately, or alternately, depending on the depth of the mine and the degree of clogging.

Cleaning a well with a bailer or pipe

Before cleaning water from a well from clay using a bailer, you need to:

Remove and free the shaft completely from foreign objects.
Fix the bailer on a rope or a sufficiently strong metal cable and smoothly lower it to the bottom.
After reaching the bottom, the bailer rises 50 centimeters and then drops sharply under its own weight.
From a sharp blow to the bottom, the clay begins to move, and free space filled with particles.
From a sharp fall, the intake channel opens a metal ball, and water with clay goes inside the bailer.
When lifting, the channel closes the ball, and dirty water is retained in the cylinder.
Such movements must be repeated 2-3 times, then the cylinder slowly rises to the surface.

Each such procedure lifts up from 250 to 500 grams of clay. This cleaning process is lengthy, but in practice it turns out to be quite effective.

Cleaning the well with a vibration pump

The simplest and fast option cleaning - use a vibration pump. It is used in all types of structures, especially in mines where the receiver is narrowed, and cleaning with a deep unit is not possible.

Tip: Before you clean the water from the well from clay using this method, you need to purchase a pump that has a protruding water intake in the lower part of the case.

A durable rubber or durite hose is put on the water intake and securely fastened with metal brackets.
The length of the hose depends on the size of the constricted section.
The hose must have sufficient rigidity so that it does not bend when it hits the ground.
The pump descends to the bottom of the shaft, then rises by 5-10 centimeters and turns on.
The hose collects and pushes the sludge deposit to the surface, but with such a heavy load and clogged valves, the pump will quickly break down. Therefore, it is recommended to periodically remove it from the shaft for washing with clean water.

Cleaning with two pumps

The method is characterized by a long duration, but at the same time a person may not participate in the process.

Before you clean the well from clay by this method, you need to prepare in advance:

Up to 300 liters capacity for liquid.
Centrifugal pump for pumping water.

Deep pump cleaning

This method is as follows:

From the tank, it will supply water under pressure through a hose to the bottom of the well, while washing away the clay deposit.
A deep pump will pump water back into a container with washed clay. This forms a closed flushing system.

Tip: It is better to take pumps with approximately the same performance.

The deep pump rises from the bottom of the well by 15 centimeters.
A weight is attached to the end of the injection hose immersed in water or a metal tube is put on to prevent twisting of the end and direct it clearly to the bottom of the shaft.
On the suction hose centrifugal pump it is better to put on a filter so that small pebbles or sand do not accidentally get into the pump.

How bentonite clay is used for drilling wells can be found in the video. This article gives the most common methods for cleaning clay from wells.

What to do if the well is not pumped?

So:

If the source of water is not pumped, then certain mistakes were probably made in its construction.
Maybe the depth of the well is much greater than in the calculations.
There is also reason to believe that the pumping equipment for pumping was chosen incorrectly.
There is a possibility that there is simply not enough water at this depth.
For this reason, it is worth continuing drilling to a more aquifer in the area.
It may be that sand is constantly present in the source. There is water, but dirty.
In this case, you should pay attention to the pump and filter.
Pumping won't help.
Such a source can be pumped for several years.
This is due to the fact that sand is located next to the aquifer, and its layer in the soil was affected by drilling.

In order to avoid problems with the construction of a water source on the site and in its further operation, it is worth contacting special companies that will provide professional well drilling services and give guarantees for their work.

The studies at the site ended successfully and now the work on drilling the well is being completed. All worries are over, very soon it will be possible to taste the water from the depths, but there is one more important stage, without which the high-quality operation of the well is almost impossible. We will talk about how to pump a well after drilling in order to get crystal clear water in this article.

What is needed for

After the drilling of the well is completed, it must be pumped. When the pump is first started, muddy, completely unsuitable water comes out of the pipe. Such water cannot be used even for technical needs. You can turn off the pump and leave the well so that the water in it settles. In this case, the well will silt up very quickly and will not produce water.

The aquifer contains both large particles and the smallest. Constantly moving, myriads of particles pass through the screen and gravel filters, settle to the bottom of the trunk, gradually silting it and reducing the depth of water intake. At first, you will be able to get clean water, but very soon the productivity of the well will drop to zero.

Well pumping at the very beginning of operation is necessary in order to remove all the smallest particles from the aquifer located near the pipe. On the initial stage pumping from the well will be very dirty water. The more it is pumped out, the cleaner and lighter it will become. For deep structures in clay or limestone, it will take several weeks to get a good pumping. For shallow wells in the sand, it will take up to 12 hours to pump water.

The duration of pumping a well in alumina areas is due to the fact that a muddy clay solution is formed both during drilling and during active flushing. Fine clay particles penetrate into aquifers and are very difficult to wash out. You will have to pump out too much water to achieve the desired result. As a result, after a long cleaning process, you will be pleased with clean tasty water and a long service life of the well.

Carrying out technology

Intensive pumping of water from a finished well at the beginning of its operation is called well pumping. To obtain a good result, several very important aspects must be observed.

Pump selection

A new powerful pump purchased to supply water to the site is not recommended to be lowered into the constructed well. Expensive equipment is better used for pumping good water. It is desirable to carry out the process of pumping a well with a submersible pump purchased at a low price. During operation, the pump will periodically fail due to a large number cloudy suspension, but it is enough to achieve the desired result. Only a submersible centrifugal pump model can cope with such a large load.

Hanging Equipment

When pumping a well, pay attention to the height of the centrifugal pump. Measure the depth of the bottom of the well. The pump should be lowered 80 cm above the bottom so that it is in line with the gravel pack. This arrangement of equipment allows you to maximize the capture of sludge and bring it up. The pump must be periodically turned off, lifted up and thoroughly rinsed with clean water.

Duration

There are no exact data on the time spent. The duration of the process depends on the degree of contamination of the well and on the intensity of water intake. The more water will be pumped out. the more small particles will be brought to the top. The coarse sand not passed through the filter will settle to the bottom and will act as a filter layer.

Note! To get a good result, you need to pump out several tens of tons of groundwater.

Mistakes

Common Mistakes:

The pump is lowered too close to the bottom of the well. In this position, the equipment does not work well, quickly becomes clogged with silt and stops. It is possible to completely submerge the pump in mud. Getting the device out of this position is quite difficult.
The pump is too close to the top of the aquifer. In this position, its use does not make any sense. The main part of fine particles settles closer to the bottom of the well. Pumping carried out in this way will not give good results and very soon the well will cease to function.
The water pumped out of the well should be diverted away from the structure so as not to fall back to where it was pumped out from. Ill-conceived drainage of dirty water can lead to a protracted well pumping process.
The pump should be lowered into the well not on a cord, but on a thin cable. If suddenly the equipment gets stuck in the mud, the cable will not break, and you can get the pump to the surface.

The fight against silting

Periodically performing preventive maintenance, you will extend the life of the well. Run the pump regularly for at least two hours during drawdowns. You can try to wash the plug formed at the bottom of the silt. To do this, you need to open the well and lower the hose down to the pump. By supplying clean water under pressure to the hose, you will wash away the formed bottom sediments. Water with sediments will rise up the annular space and spill out of the well. You need to rinse until you see bottom gravel in the splashing water. After that, you need to pump water from the well.

It is not difficult to operate a well if drilling and construction of the structure are carried out in compliance with the technologies. Properly carried out pumping of the well will allow you to provide your home with clean water in sufficient quantities for a long time.

Video

About the rules for pumping a well, see the following video:

;

How to pump a well after drilling should be known to those who decide to acquire an autonomous source fresh water in your area by the most optimal solution autonomous water supply for own house or cottages will be the choice to drill a well. To carry out work on the arrangement of a well, it is necessary to have qualifications and special knowledge, and that is why specialists are involved in the performance of such work. But even if the experts have completed all necessary work, using special tools, then after that it is necessary to resolve the issue with the buildup of the well. And everyone can perform the buildup actions on their own and without additional surcharge to specialists.

- Pumping a well after drilling: the basis of the process
- How to pump a well after drilling and why it is needed
- Highlights: How to Check the Depth of a Well After Drilling
- Well flushing after drilling
- How to properly pump a well after drilling (video)

Many people think that the aquifer is the layer that flows from the tap, but this is not so. In nature, the aquifer is a sand-clay mixture, which is compressed between a sandy loam and a clay lens. It is from this mixture that water is extracted, which is purified using mechanical filters. But, unfortunately, mesh filters are not able to clean the smallest particles. And besides the fact that the filter does not clean fine particles, they also penetrate into the middle of the filter and clog it from the inside.

In the end, the owner of a newly drilled and equipped well must pump this mixture to the bottom, thereby increasing the efficiency of the filters and the quality of the water.

A pump with a filter needs to pump a new well and build up the conditions for operation in the future.

Also, during the buildup, sand and silt are washed out not only from the pipe, but from the environment of the layer. And that is why the rocked well is surrounded not by a muddy suspension, but by a layer of pure water, but to achieve such a result, it is necessary to make an effort.

The process of pumping a well after drilling

For successful pumping, you need to know 3 basic rules:

The first is waiting for the time required for the buildup of the well;
The second rule that you need to know is which pump should do it;
And the third rule is how to organize the pumping process: when to start pumping, where it is better to fix the pump, and so on.

Experts point out that if the buildup of the well is done correctly, it will make it possible to remove all the smallest particles from the aquifer, which is located directly next to the pipe. An increase in a new well with a small debit is the dream of every summer resident, this can be done in a vibrational way, the most important thing is not to make mistakes, especially during winter. After the well has been drilled, the next step is to flush the water that is being pumped. This can be done without any problems with your own hands, detailed description how to get rid of sand in the water, pump out silt, as well as increase the flow of clean water, you can learn from the video.

How to pump a well after drilling and why it is needed

Contrary to your expectations that clean water will flow immediately, this is not so, first of all, water appears in the pipe, which is not suitable for drinking, it needs to be cleaned. And if no cleaning decisions are made, the well will soon silt up and be unsuitable for water production.

The aquifer contains not only large stones and sand, but countless small particles that the filter is not able to clean. These particles easily pass gravel and screen, and then settle to the bottom of the well, making it shallower and seriously reducing productivity.

The well after drilling must be pumped

After drilling is completed, very turbid water enters the well, and in the course of gradual washing out, this liquid brightens and becomes transparent.

The time to build a well depends entirely on what type of soil you are facing and can last from 12 hours. If the sandy soil and the well is not very deep, then a few weeks, and if it is drilled in clay or limestone and deep enough, then such a process will take several months.

The owners of land plots that are located on alumina are very interested in the question of how to pump a well passing through clay. Such pumping will be a very long process, since during drilling and subsequent pumping, a cloudy clay solution is quickly formed. It also seeps very deep into the aquifer and is difficult to wash out. And pumping such a well can take weeks and even months. For such an amount of time, a huge number of cubes of muddy liquid will be pumped out, and as a result, the cleaning process will be successfully completed.

Highlights: How to Check the Depth of a Well After Drilling

There are several options for how to measure the depth of a well, and their difference is in accuracy, complexity and accessibility.

Also among the options there is a mechanical method, it is available to almost anyone, and there are also more technological methods of measurement, but they are used for special studies.

For the mechanical method, you must have: a ruler or tape measure, a rope. To check the depth of the well, carefully lower the metal weight on a rope (cord) to the bottom. It is necessary to lower the load until the tension of the rope begins to decrease, after that we measure the depth with a ruler by winding the rope around it. You can also find out the amount of water in the well by the wet part of the rope.

You can check the depth of the well in several ways.

But with this simplicity of the method, there are significant drawbacks. The first disadvantage is the possibility of measuring a well no more than 10 meters. The second disadvantage is that the wet part of the rope makes it possible to know the static water level, and a dynamic one is needed to submerge the pump.

Measurement option using a short cable with magnetic marks. This method is very similar to the previous one, but performed with a different approach. This method uses a cable reel and a reader. Magnetic marks are applied to this cable after a certain distance, these marks are processed by a receiving device, thanks to which they receive accurate information about the location of the load.

Well flushing after drilling

Well flushing is carried out using pipes that sink to the bottom and supply water at the highest possible pressure. The pressure of the water washes out the silt and all the dirt that has accumulated during the operation of the well. When flushing, the accumulated dirt particles rise through the pipes and are removed to the outside.

When creating this mechanism, a method was involved that is used in fire system. The amount of water that enters the well is limited.

When flushing a clogged well while drilling, it is very important to be careful to avoid damaging the filter.

Washing the well under high pressure and using pipes

For the tightness of the cleaning process, it is necessary to fix the pump, on upper part pipes by putting an adapter on it, and this adapter is fixed with pipes with self-tapping screws in the amount of 4 pieces. The volume of water used will depend entirely on the size and characteristics of the well, as well as the degree of contamination.

How to properly pump a well after drilling (video)

As you can see from the article, pumping a well is not so simple. If you do not have certain skills, then it is better to seek help from professionals who can carry out the full range of quality work. Of course, after familiarizing yourself with the basics, you can do the work yourself, but then the question of quality will remain open, and the work will have to be redone.

In some cases, the well mechanism is the only way to provide water supply for autonomous private households. In order for the owner to receive clean water without interruption, only professionals should make a well and equip the source. But you can figure out how to swing a well after drilling to remove clay, sand and silt impurities from a reservoir, you can do it yourself.

Why do you need to do this

It is necessary to pump water after drilling a well to remove muddy sediment, particles of sand and silt that got into the aquifer during the process of “drilling” the soil. If such a procedure is not carried out, the drilling products will settle on the bottom and walls of the well and tightly clog the water intake.

You need to know the following about pumping:

The process will take a lot of time - shallow wells are cleaned in about 12 hours, deep and polluted - in a day. There are cases when turbidity was removed from the water for weeks.
Wells drilled in clayey or limestone soil are the dirtiest, so the buildup takes longer and requires more pump power (and even more of them).
The procedure is completed only when completely clean and transparent water comes out, otherwise the source will quickly become clogged.

Dirty water from a recently drilled source should also be pumped out to protect the well from excessive silt formation - its particles accumulate, reducing water quality and reducing the depth of the reservoir.

Tools and materials

The main tools for proper rocking of the well are:

A submersible pump of a centrifugal model, preferably inexpensive, since in the process of removing sediment from the aquifer, it will become clogged and fail. In difficult cases, it is possible to lose from 2 to 5 mechanisms per procedure.
A strong cord or cable on which the pump is suspended and lowered into the well;
"Sump" - a barrel with a volume of more than 200 liters with a perforation in the lower part: water, passing through the barrel and pouring out through the holes, will be cleared of sediment. By how quickly the suspension is filtered, one can judge the process of rocking the source.

The most important tool - the pump - will need to be removed from the well from time to time, flushed and cleaned so that the mechanism can continue to work.

The process of building a well

Well cleaning after drilling takes place in several stages.

Choice of location. As far as possible from the future well, with the installation of treatment facilities-barrels.
Hanging the pump on a cable and lowering it into the well. 70-80 cm above the bottom, so that it is possible to capture all the particles of sand and clay, preventing them from settling to the bottom.
Turning on the pump and actually cleaning the source. During the procedure, the mechanism will have to be removed and cleaned several times.

As soon as clear water begins to flow from the cleaning barrels, the procedure for rocking the well after drilling can be considered completed.

In cases where the well is idle for a long time (for example, in the autumn-winter period), or if a decrease in water pressure is noticed, it is recommended to carry out a preventive 2-3 hour start of the pump to remove the silted soil layer.

Pumping a well after drilling is a simple task. If you set yourself the goal of ensuring that only clean water comes from a new source, choose the right tools and be patient while removing drilling products from the reservoir, this procedure will be relatively easy. This is within the power of the owner of the future well and without the help of professionals.