Pulse counter tachometer ID 2 overall dimensions. Where can I find the number on the water meter? Where to find the official serial number of the standard water meter

27.03.2020

The desire to save money when paying for water supply leads to the installation of a water metering device (PU). In order to fix the fact of installation and operate it in the future, you need to know the serial number of the meter. There are several options where you can see the number indicated on the water meter.

Each instrument, when manufactured at the factory, is assigned a serial number. It must be specified when registering a PU in management company, HOA or water utility (if there is a direct supplier of the resource).

Since the flow rate of both cold and hot water, then both counters are registered. Each PU has a technical passport, which contains different information.

The serial number of the meter is required when making payments for cold water and hot water via SMS or an Internet resource. The testimony of the PU, together with it, is transmitted monthly in messages and by phone.

The serial number of the meter is required for installation and operation by the consumer.

Where to find the official serial number of the standard water meter

The situation when you need a water meter number arises both before and after installation. The article below describes what to do in a particular case.

At the time of purchase

When a client buys a meter, it is imperative to check whether the serial number indicated on the meter matches the number printed on the accompanying document (data sheet). It is worth doing this in order to avoid problems in the future. As a rule, the number is indicated on front side meter (scoreboard). Very rarely, it is knocked out on the side or back of the device.

Elements on the water meter

Illustrative examples of placing serial numbers on cases popular models water meters.

Important! Only a numeric value should be specified.

Location of the number on the meter — 1 Location of the number on the meter — 2 Location of the number on the meter — 3
Location of the number on the meter - 4

It is better to purchase a meter in specialized stores, and not in the market. And even more so out of hand. At a minimum, it may be without the necessary documentation and informative component. As a maximum, to function incorrectly or not to work at all. In any case, the meter will not be installed at all or will not be registered.

On a device already installed

If you need to find out the meter number when it is already installed, you can use several options:

the digital value is written on the body of the meter. If the information is posted on its scoreboard, then easier way can not found. But when the number is on the side or behind, then it is problematic to do this without dismantling;
in the technical passport of the device;
in documents drawn up during registration in the UK, HOA;
in the service serving the address area;
in the act of installation or verification.

You can use any convenient option.

Counter number in the documentation

One of the first pages of the technical passport for the water meter contains information of interest.

Advice! When the device is just purchased in a store, it is advisable to make a copy of the first and last pages.

You can find out the number of the meter using the technical passport of the device.

Sometimes enough information from the data sheet. But it happens that it will have to be compared with the one on the meter. If it is not available, use one of the following methods:

if the remote control was delivered recently, there is an installation certificate with the date, name and number of the device. It is made in duplicate. The first copy remains in the hands of the owner of the apartment, the second - in the organization that carries out the installation. It happens that the owners lose the act. Then you should directly contact this company for a copy of the act (or oral answer);
when registering a meter on this personal account in the UK, HOA or other utility organization, all information is recorded. You can request data from these companies;
employees of the water marketing establishments visit the houses in a planned manner once a quarter, checking all appliances and taking control readings. It is worth calling this service or asking the employees themselves during the next round of apartments;
in the case when the PU has been verified, the certificate contains information about the serial number. This document is drawn up similarly to the installation act in two copies, one of which remains with the verification customer. If the document is lost, the metrological service performing the verification will issue a copy of the certificate or verbally report the information.

The receipt for payment of housing and communal services, in addition to the consumed volumes and charges, contains information about metering devices. It can be viewed in a certain place (receipts come in different formats and types).

Information about the meter in the receipt - 1 Information about the meter in the receipt - 2

Sealed (frost-resistant) electronic pulse counter - tachometer " ID 2" created for:

Counting the number of pulses coming from sensors (inductive, optical, ultrasonic, etc.) to the counting inputs (INP1 and INP2) of the ID-2 electronic pulse counter and converting them into the required physical units of measurement by multiplying by a given multiplier (for example, in kilometers, meters, liters, pieces, packages, kilograms, turns, revolutions, etc.);

Calculation of total output per shift, day, week, month, year (password reset);

Pulse repetition rate measurements (ID-2 pulse counter operates as a tachometer, speedometer or flow meter);

Office executive mechanisms machine tools with two discrete outputs of the device.

Features of ID-2:

– Protection against dust and water IP65 (use in dusty and damp rooms or directly under the open sky is allowed, washing with water and detergents is allowed).

– High-quality, reliable, impact-resistant case.

– It is possible to seal two screws of the cover at once, which completely excludes unauthorized access to the inside of the product.

– Reliable cable glands (protection class IP68) ensure the tightness of the device and securely fix the supply cable, which is very important in case of cable jerks.

– Cable glands with a removable sealing insert of a collet type are used, which greatly facilitates installation, the nuts have a special design that prevents spontaneous unscrewing of the nuts.

– The front panel (IP65 protection level) of the meter is resistant to aggressive environments (solvents, oils, greases, alcohol-gasoline mixtures, detergents, etc.).

– The device has high-quality “lift” type terminal blocks that do not damage the wires even when the terminals are tightened with excessive force and provide reliable contact both with and without cable lugs (sleeves).

– Wide temperature range from -30 to 70 °С (from minus 40 °С for a short time), it is allowed to use the meter in an unheated room or on the street.

– High reliability, stability of operation and noise immunity, resistance to surges and dips in the supply voltage.

– High vibration resistance (can be installed on moving parts, for example, on carriages of cable management systems).

– Simple, intuitive and user-friendly menu, access to the setpoint and reset the current readings with the push of a single button.

– Large (digit height 15 mm), bright, high-contrast indicator (display) with a light filter.

- A stabilized (switched) internal power supply with short circuit protection, a pulsed power supply for the ID-2 meter, emits a small amount of heat, which made it possible to expand the upper temperature limit (operating range) to 70 °C.

– Has a sound indication (built-in buzzer), especially convenient for people with poor eyesight.

– Pulse counter - tachometer ID-2 can operate on one (INP 1) or two (INP1 + INP2) counter inputs (normal and reverse modes of operation).

– Password protection of settings against accidental (unauthorized) changes.

Electronic impulse counter - ID-2 tachometer (impulse counter) has 4 discrete inputs and 2 discrete outputs.

Pulses from sensors (or encoder) are sent to two counter inputs. Next, there is a hardware conversion (doubling or quadrupling) of pulses into increments. The increments go to the reversible current increment counter and to the total increment counter. The operation of the counters can be blocked in the absence of a signal at input 4 (this function is configured in the parameters).

Output 1 (feedforward) is most commonly used to command a material (conveyor, cable line, etc.) to slow down before stopping (for more precise positioning of the material). The trigger point for output 1 is determined by the feedforward d.

Output 2 of the counter is triggered when the setpoint (measured length L) is reached, most often this is a signal to stop. Output 2 is triggered either for a specified time (from 0.1 to 9.9 sec.), Or switched on permanently, if the value of the current counter is greater than or equal to the setting (configured in the programmable parameters of the impulse counter - tachometer ID-2).

If the value of the current counter is in the lead zone (i.e. between L-d and L) - a continuous signal of the built-in buzzer of the electronic impulse counter - ID-2 tachometer sounds (note that if pulses are not received at the counting inputs for more than 3 seconds - the buzzer signal turns off ; this was done at the request of customers, because a long sounding signal of the built-in buzzer when the equipment is stopped sometimes interferes with people around).

Specifications ID-2

Characteristics	Values
Number of digital inputs
Number of discrete outputs
Value range of the current counter	99 999 ... 999 999
The range of values of the total output counter (hours, reset by password)	99 999 999 ... 99 999 999
Degree of protection of the electronic impulse counter - tachometer ID-2
Permissible ambient air temperature for the impulse counter - tachometer (it is allowed to use the device in an unheated room or directly on the street)	30 ... +70 degrees C (for a short time from minus 40 degrees C)
Dimensions of the body of the pulse counter - tachometer ID-2 (excluding cable glands)
Device weight	no more than 0.4 kg
The time of saving information in the non-volatile memory of the pulse counter - tachometer ID-2	unlimited
Power Consumption (when using AC power)	no more than 2.5
Power supply for the pulse counter - tachometer ID-2 (devices with a different supply voltage are commercially available: 12 ... 36 V DC / AC, batteries and chargers can be supplied)
Height of digits of the indicator of the device

Typical wiring diagram for pulse counter ID-2

Electronic pulse counter ID-2 is produced in two modifications: "STANDARD" and "LIGHT".

LITE version does not include:

Discrete input 3 (INP3) - external reset of the current value of the device;

Discrete input 4 (INP4) - device operation permission;

Discrete output 1 (OP1) - a command to the equipment to reduce the speed (preemptively);

Discrete output 2 (OP2) - a command to stop the equipment.

The ID-2 electronic pulse counter can be additionally equipped with swivel brackets (they rotate around the mounting axis by 90 degrees). The brackets make it easier to mount the meter on site, especially when marking holes for screws or self-tapping screws is not accurate.

Respect-zha-e-my consumers of com-mu-nal services! If you cannot find the meter identifier in your receipt ( , then once again make sure that the billing services of your managing organization are provided by MUE "MRIVTS". You can see the list of managing organizations in the section. If your managing organization is not in the list of our clients, then you need to transfer the readings of metering devices to the settlement center that serves your managing organization.The meter ID is not identical to the serial number of the metering device and is indicated only in your receipts.

Comments (4) to Counter ID

We live - Kola, st. Pobedy, d. 23, apt. 4 - Management Company "Kola Management Company". An invoice was received for payment of utility services through MRIVS in the id column of the meter, there is a meter identifier for hot water, but not for cold water. Counters were installed and accepted by acts at the same time. Please explain why it is missing and where to get the identification number of the cold water meter. Thank you.

MUP "MRIVTS" at your address only calculates heating and heating services, therefore there is no need to transfer the readings of the cold water meter to MUP "MRIVTS".

I would like to know the ID of the electricity meter. Turistov 29a kv 33

The receipt for gas (because there was a large overpayment and no testimony was given) does not indicate the ID meter, there is no number of our apartment on the website (Murmansk, Kirov Ave., 53a, apt. 12). How to submit evidence?

Attention!!! This post is outdated.

Special price: 3850 r with VAT
Sealed electronic impulse counter - tachometer ID-2 (impulse counter; counter of revolutions, turns; length meter) - frost-resistant has the following features:
Pulse counter. You can watch videos about tests of the ID-2 electronic meter:

Crash test counter ID-2 (mechanical strength test, the device was moved by a car);
Pulse counter test - ID-2 tachometer for tightness (IP65);
NEW Test of the pulse counter in extreme low-temperature conditions (the operating pulse counter ID-2 was immersed in water and frozen).

The purpose of the electronic counter - tachometer ID-2
Pulse counter / tachometer ID-2 is designed for:

counting the number of pulses coming from sensors (inductive, optical, ultrasonic, etc.) to the counting inputs (INP1 and INP2) of the ID-2 electronic pulse counter and converting them into the required physical units of measurement by multiplying by a given multiplier (for example, in kilometers, meters, liters, pieces, packages, kilograms, turns, revolutions, etc.);
calculation of total output per shift, day, week, month, year (password reset);
measurement of the pulse repetition rate (ID-2 operates in the mode of a tachometer, speedometer or flow meter);
control of the actuators of machine tools with two discrete outputs of the device.

Most often, the ID-2 electronic counter (impulse counter) is used as:

revolution counter;
coil counter;
inclusion counter;
length meter (counter of length, footage);
counter of quantity, volume;
tachometer (speedometer, flowmeter);
automatic control unit (machine) for dimensional cutting of long materials.

The operation of the pulse counter - tachometer ID-2 (pulse counter). counter device.

Electronic counter of revolutions, turns, pulses - ID-2 tachometer (impulse counter) has 4 discrete inputs and 2 discrete outputs.
Pulses from sensors (or encoder) are sent to two counting inputs (input 1 and input 2) of the counter ID-2.
Next, there is a hardware conversion (doubling or quadrupling) of pulses into increments. The increments go to the reversible current increment counter and to the total increment counter. The operation of the counters can be blocked in the absence of a signal at input 4 (this function is configured in the parameters).
The current increment counter can be reset by a signal at input 3 of the pulse counter - tachometer ID-2 (external reset).
The total counter can only be reset via a password; when the total counter is reset, the current counter is automatically reset as well.
The value of the current increment counter is multiplied by a conversion factor (multiplier) designed to convert the counted increments into the required physical value (most often in pieces, meters, decimeters or centimeters). The range of values of the conversion factor: 0.00 001 ... 9.99 999 (set in the programmable parameters of the counter - tachometer ID-2).
The required physical value and speed (or consumption) is displayed on the LED indicator of the impulse counter - ID-2 tachometer. Logic devices (LU1...LU3) are used to control discrete outputs and the built-in buzzer of the pulse counter - ID-2 tachometer.
The pulse counter - tachometer ID-2 signals about the decrease in the mains voltage below the permissible level by the indication on the indicator "8.8.8.8.8.8." (all digits of the indicator are lit). When the supply voltage fails, the values of the counters are stored in the non-volatile memory of the device. Thanks to this, when power is restored, it is possible to continue the interrupted technological process without loss of information. When the power is restored, the counter values are read from the memory, and the indicator readings begin to glow intermittently ("blink"), indicating that the device's power has been turned off, i.e. an error may have occurred (the pulse counter did not work, and at that time pulses could be received at the counting inputs). The power off indication is a very convenient and very useful feature, which is often missing from devices from other manufacturers. The diagram of operation of discrete outputs and the built-in buzzer of the counter ID-2 is shown in the figure.

Output 1 (feedforward) is most commonly used to command a material (conveyor, cable line, etc.) to slow down before stopping (for more accurate positioning of the material). The trigger point for output 1 is determined by the feedforward d.
Output 2 of the ID-2 counter is triggered when the setting (measured length L) is reached, most often this is a signal to stop.
Output 2 is triggered either for a specified time (from 0.1 to 9.9 sec.), Or switched on permanently, if the value of the current counter is greater than or equal to the setting (configured in the programmable parameters of the impulse counter - tachometer ID-2). If the value of the current counter is in the lead zone (i.e. between L-d and L) - a continuous signal of the built-in buzzer sounds (note that if the counting inputs do not receive pulses for more than 3 seconds - the buzzer signal turns off; this is done at the request of customers, t .k long sounding signal of the built-in buzzer when the equipment is stopped sometimes interferes with people around). Specifications electronic hermetic counter - tachometer ID-2 (pulse counter) Parameter or characteristic of the counter ID-2 Value Number of discrete inputs of the counter ID-2 4 Number of discrete outputs of the counter - tachometer ID-2 2 Range of values of the current counter -99 999 . .. 999 999 The range of values of the total output counter (running time, password reset) -99 999 999 ... 99 999 999 humidity or directly under the open sky, washing with water is allowed) IP 65 Permissible ambient air temperature for the counter - tachometer (it is allowed to use the device in an unheated room or directly on the street) -30 ... +70 degrees C (for a short time from minus 40 degrees .C) ID-2 case dimensions (excluding cable glands) 94x94x57 mm Device weight no more than 0.4 kg Information storage time in the non-volatile memory of the meter - tachometer ID-2 unlimited Power consumption (when powered from the AC mains) no more than 2.5 and chargers) 150 ... 255 V (45 ... 55 Hz) The height of the digits of the indicator of the device is 15 mm Connection of the electronic impulse counter ID-2. Typical connection diagram.

The device can work on one channel (only INP1, normal, non-reversible mode of operation) or on two channels simultaneously (INP1 + INP2, reverse mode, with detection of the counting direction). The use of the inputs "external reset" and "permission of operation" is not mandatory, in the modification "LITE" the inputs "external reset" and "permission of operation" are absent at all (see below). : Electronic counters - ID-2 tachometers (pulse counters) are produced in two modifications: "STANDARD" and "LIGHT". LITE version does not include:

discrete input 3 (INP3) - external reset of the current value of the device;
discrete input 4 (INP4) - enable the device to work;
discrete output 1 (OP1) - a command to the equipment to reduce the speed (preemptively);
discrete output 2 (OP2) - a command to stop the equipment.

The counter for counting impulses (electronic) - the ID-2 tachometer can be additionally (this must be specified when ordering) equipped with swivel brackets (they rotate around the mounting axis by 90 degrees), the brackets facilitate the installation of the ID-2 counter - tachometer on the object, especially with inaccurate marking holes for screws or self-tapping screws; in addition, quite unexpectedly for us, customers noted another useful function of the brackets, which increases the reliability of the device as a whole: if you “accidentally” hit the meter with a loader (or a crowbar, sledgehammer, etc.), then the brackets break off, the device hangs on the wires, but continues to work ... however, if you have such "heavy" operating conditions - we recommend that you think about buying a spare device, so, just in case of a "fire accident" ... :) Russia, however ... We will be grateful to you for any constructive wishes and feedback. It is possible to manufacture devices with a modified program on the instructions of the customer. Operation manual (instruction) for a sealed electronic counter - tachometer ID-2 (speedometer, flow meter, coil counter, revolution counter, inclusion counter, length meter, length counter, footage) can be downloaded here: download link. Please note: wholesale and regular purchases of hermetically sealed electronic meters - ID-2 tachometers are subject to special prices.