How to make a do-it-yourself walk-behind tractor with a box from a Zhiguli and a vase rear axle. Do-it-yourself home-made walk-behind tractor from a bridge from a Zhiguli What can be done from the rear axle of a Zhiguli

25.04.2020

Is it possible to make a walk-behind tractor with your own hands from rear axle VAZ? It will not be possible to assemble a full-fledged walk-behind tractor, but the trailer from this unit for agricultural machinery will turn out to be excellent. Of course, a number of changes will have to be made to the design of the bridge, but this will help us properly assemble the new trailer frame in the future.

Assembling a walk-behind tractor from scratch

If you are going to design a complete walk-behind tractor with your own hands or even a whole mini tractor, before starting work, you should think about the feasibility of implementing such a project. The modern market can offer the user many models of domestic and Chinese-made walk-behind tractors, whose characteristics allow for work of low and medium difficulty. At the same time, the price of such equipment is quite affordable for many users. So a project to create your own walk-behind tractor should have the following advantages:

low cost;
the possibility of using in the assembly of old spare parts from equipment, cars or motorcycles;
performance improvement in comparison with the factory analogue;
additional functionality.

The project is worth implementing if at least 3 of the listed points have been met. Otherwise, the idea is not worth the cost and it’s easier to buy a ready-made walk-behind tractor, even a used one, with a subsequent update of the parts.

Now about the design. You need to find a drawing according to which the homemade product will be assembled. The drawing will indicate the main parts, the features of their installation, as well as the method of manufacturing fasteners for spare parts. Without documentation, it will be impossible to implement the project, so the primary task is to find the most suitable drawing. After that, you can start the selection of materials.

Parts, assembly of new units and complete set of walk-behind tractor

Unfortunately, not many parts can be used from an old VAZ for a walk-behind tractor. Here is a list of what will come in handy in one case or another:

engine, since Zhiguli has a gasoline engine, this option is not the most economical;
fuel tank and parts of the fuel system;
exhaust gas system;
air filter;
starter;
steering wheel, gas and clutch levers;
gearbox, razdatka;
wheels;
rear axle - useful for assembling a trailed structure.

In fact, this is all that can be used from the VAZ. It is very difficult to make a home-made walk-behind tractor from the Zhiguli bridge and similar VAZ models without many transformations, so you have to use only individual parts of the chassis.

Usually, a diesel engine is taken for a walk-behind tractor, so it’s worth delving into old motorcycle equipment, for example, in the same motorcycle. There are some homemade saws with engines, but they are used for light ground work.

The choice of engine is very important, so be guided by the type of work that will be performed by the walk-behind tractor. For medium loads with plowing the land and harvesting, a motorcycle engine is enough, and for more labor-intensive work, a car engine will be required.

In some cases, if there are not enough parts, you can buy original spare parts for walk-behind tractors and use them in the design. This option should be considered only if the drawing contains recommendations and examples for reworking purchased parts.

Since we need to get a working prototype, try to follow all the instructions as fully as possible and do all the work according to the scheme and drawings.

Mini tractor

A minitractor differs from a walk-behind tractor in that its power is higher, which means that the scope of equipment in the economy is increasing and changing. It is quite easy to make a mini tractor out of walk-behind tractors by connecting a suitable trailer. Here you can use both the factory model of the walk-behind tractor, and its home-made counterpart. It will turn out such a walk-behind tractor from the bridge from the Zhiguli and with a trailer. As an engine, it is still worth taking a diesel one, preferably more powerful. This assembly option also involves the use of a special drawing.

From the Zhiguli, not only the rear axle is useful, but also the gearbox. Some modifications will be needed:

The top of the gearbox is cut off, it is bolted to the homemade frame. The pulley ratio is 1:4.
A chain drive is pulled from the gearbox to the bridge, adjusting sprockets are installed with an efficiency ratio of 1 to 3.8.
The bridge itself is bolted to the frame of the walk-behind tractor.
The wheels are made from Zhiguli disks. You can disassemble the structure along the welds, and then narrow the disc itself by investing a smaller part in a larger one and scalding the resulting part by welding.

The option involves the use of 2 ready-made units: a walk-behind tractor and a trailer.

Using the rear axle VAZ

What you can definitely do with your own hands is a multifunctional trailer from the rear axle of the Zhiguli.

To do this, you need a few materials:

steel tubular blanks 60x30 and 25x25 mm;
wheels and springs from the rear axle of the Zhiguli;
sheet pieces of steel from 0.8 mm thick;
channels, sheets of duralumin from 2 mm thick.

trailer body can be assembled different ways. One of the most common options is wooden with metal corners and screw fasteners. The work process is as follows:

The wooden frame is attached to the metal structure of the rear axle.
Metal parts are welded together.
Cross beams are made from a profile of 25x25 mm, tubular blanks are useful for side members.
From the corners of 25x25 mm we make a metal strapping for the frame, weld it to the lower bridge.
Next, the beams are connected.
With the help of springs we connect the side members to each other. To do this, the edge of the springs is carefully put on the axis of the beams. The beam is connected to the central part of the structure by ladders.
The last part is a triangular drawbar, which is welded from metal pipes. The drawbar is welded to the metal frame.

It remains to build the transition from the drawbar of the trailer to the walk-behind tractor.

Conclusion on the topic

The entire Zhigul cannot be used to assemble a walk-behind tractor. The most necessary parts of the structure from this VAZ model are: the rear axle, which is used mainly for trailers; checkpoint; exhaust system and fuel tank.

All other parts are practically useless. It will take a long time to look for a suitable drawing in order to realize the old Zhigul to the maximum in the form of a new agricultural machine. But there are similar projects, and they were successfully implemented by other craftsmen, it remains only to find the necessary drawings.

Many people are interested in whether it is possible to make a walk-behind tractor with their own hands. A heavy walk-behind tractor or compact walk-behind tractors are indispensable helpers in agriculture, but not all farmers and summer residents have the opportunity to purchase such equipment. Therefore, if you have certain skills, knowledge and skills, you can assemble a walk-behind tractor with your own hands. In order for the self-assembled motor cultivator to serve for a long time, a project scheme is created. It is necessary to correctly measure parts, purchase materials and tools, and complete technical drawings and dimensions of assemblies. You can use one of the instructions of craftsmen who write on special forums how to make a walk-behind tractor with their own hands.

Any recommendations on the Internet on how to independently complete a walk-behind tractor must be checked from reviews. It is good if friends or acquaintances are users of such home-made walk-behind tractors. Then their reviews can be trusted, in other cases, all tips on assembling and using home-made devices must be checked.

How to assemble a walk-behind tractor yourself

Consider how to assemble a walk-behind tractor with your own hands. Parts that can be used for DIY are taken from old motorcycles and scrap metal. As an engine, which is often put on home-made motor cultivators, you can use the motor from Friendship - chainsaws.

Such an engine has sufficient power, allows you to use various attachments. This greatly expands the functional use of motor cultivators. Many put on a walk-behind tractor an engine from an Ant scooter, which has excellent characteristics and parameters for working in a summer cottage.

To create a walk-behind tractor at home, you will need the following spare parts and materials:

Steel corners measuring 36x36 mm or pipes 60x50x2 mm. From these parts you can assemble a frame for a walk-behind tractor.
The engine is fully assembled.
Fuel tank.
Exhaust system.
Air filter.
Kickstarter.
The steering wheel, on which the clutch and gas handles should stand.

The following tools will help you make a walk-behind tractor with your own hands:

Apparatus for welding.
Drill.
Vice.
A set of horns and spanners.
A machine for grinding, on which a special disc for cutting metal must be installed.

Scheme for creating a walk-behind tractor

A self-made walk-behind tractor from the ZAZ gearbox consists of 2 wheels, is self-propelled, assembled with an engine that has forced cooling of the cylinder head. It is carried out with the help of air. The motor must be selected such that it can operate at different speeds, including small ones, and is able to perform large amounts of work. You can put the motor from the scooter, and remove other elements from it:

cables for control;
engine mounts;
handles;
chains;
arc, frames.

The brakes on the walk-behind tractor are used both factory-made and our own. Homemade brakes will allow you to take into account the necessary parameters and loads.

With everything you need at hand, you can make a homemade mini-cultivator at home quickly and without any problems. A walk-behind tractor based on the ZAZ checkpoint is created as follows:

A U-shaped frame is cooked from pipes.
On the lathe you need to cut the wheel axle.
Make 3 homemade hinges that are installed on the front and control rods. This approach in the assembly was used by the designer Arkhipov when he made his walk-behind tractor. Hinges were used to connect the cultivator, steering wheel and plow.
Weld on the machine frame steel pipe on which the axis should be. It is needed to implement the tension that is transmitted to the gearbox. In order for such tension to be constantly present, it is necessary to make a rocking rocker.
Weld the shift knob. For these purposes, a small piece of steel pipe is suitable.
The chassis can have a chain pitch that is 12.7 and 15.9 mm. Sprockets on the chain have the following characteristics - output shaft - 11 mm, secondary shaft - 60 and 20 mm, running axle - 20 mm.

The main stages of manufacturing a walk-behind tractor:

The frame is welded, on which the engine must then be installed, 2 pipes in the form of an arc.
A fuel tank is attached between them.
We assemble the motor using a bracket, which is also welded to the frame.
It is necessary to hang a motor with a suspension on the axle, and then all the parts are connected to the frame arcs.
Installed secondary shaft.
The control cables are stretched.
Chains are stretched.

Transmission and clutch

A self-made cultivator based on a VAZ gearbox or based on a manual transmission must have an excellent transmission. It is needed in order to transmit torque from the motor to the wheels, change the speed and direction of the car. This part of the walk-behind tractor consists of nodes that are connected in series to each other:

reducer;
differential;
clutch;
Transmission.

Reducers and gearboxes are divided into several types:

Most optimal solution- installation of a gear transmission on the walk-behind tractor, which has several forward and reverse speeds.

In motor cultivators, transmissions can be used, which consist of 2 gearboxes - gear (mounted from above) and worm (lower). This design is suitable for light and medium vehicles, but for heavy walk-behind tractors it is necessary to install more modernized versions.

Worm and gear transmission can be equipped with a centrifugal automatic clutch. A belt drive on gearboxes of this type can also act as a clutch, which performs its functions through a tension roller and a control mechanism (traction and levers).

An important part of the transmission and clutch is the release bearing. The speed of torque transmission depends on the release bearing.

Chassis and control

The chassis is a frame on which all the parts of the walk-behind tractor and wheels must be attached. When there is no frame, then the transmission performs its functions, and the motor and wheels should be mounted on it.

On the chassis, you can put parts from the car, for example, from the rear axle of the Zhiguli.

This is suitable option in order to change the distance between the wheels and set the track of the desired width. If there is no rear axle from a Zhiguli, then an Ant or an all-terrain vehicle will do.

It is customary to use 2 types of wheels on walk-behind tractors:

Pneumatic.
Weighted metal, which have lugs. They are bolted to the wheels or welded on. Additionally, other loads can be hung on metal wheels to increase the weight of the walk-behind tractor and improve traction.

The walk-behind tractor is controlled through a system of levers, gearshift rods and a steering wheel. Some models have seats for the operator, but in general the vehicle is operated only manually. You can place the desired structures on the following nodes.

On the left side of the steering rod is a clutch control lever and an emergency stop of the engine.

On the right side gas, wheel drive and brake levers are installed.

Zhiguli shortened rear axle for homemade walk-behind tractor

For the construction of a home-made walk-behind tractor, you can use the rear Zhiguli (from the VAZ car) bridge, but for this it must be shortened. This is done simply: the axle shafts are cut, as well as the bridge body itself, of course, this is all done separately and a piece is cut out. Then everything is welded, that is, the axle shafts and parts of the body of the rear Zhiguli axle. Everyone chooses the right track width for their home-made walk-behind tractor. In the photo, each semi-axle of the Zhiguli bridge from the VAZ-2106 car was shortened by 287 mm and as a result, the track of the home-made walk-behind tractor will be 700 mm, taking into account the width of the wheels (that is, from the middle of the wheels). It is planned to install Zhiguli wheels on this home-made walk-behind tractor. View the walk-behind tractor assembly with the engine from the Minsk motorcycle and the rear axle from the six (copy the address (select and press Ctrl + c at the same time) and paste it into the browser window (Ctrl + v):
motoblok.populjarno.com/photo/motoblok_svoimi_rukami/tormoznoe_ustrojstvo_dlja_motobloka/zhigulevskie_kolesa_na_samodelnom_motobloke/10-0-124

Open photo Shortened rear axle of the VAZ-2106 enlarged. If this is a drawing or diagram of a device, you can download it to your computer by opening it in large size and using the "Save image as." (right mouse button) function.
Please rate this article by highlighting the appropriate number of stars.

Most often together with this material on the topic

"for a homemade walk-behind tractor"

You can view all photos, drawings, pictures and diagrams from the category "Motoblocks from cars" by clicking on link. You will find even more materials with descriptions of how to make a cultivator yourself and accessories for it in the section " Photo of homemade walk-behind tractors» or by making a selection from all materials of the site motoblok.populjarno.com for the following MARKS:
from the car, wheel axle, Mechanisms, Reducer.

Perhaps what you are looking for is in one of the most viewed sections of our site:

DRAWINGS AND PHOTOS OF HOME-MADE MOTOBLOCKS AND ATTACHMENTS
(CLICK ON THE PICTURE or name):

Each owner of suburban real estate is faced with the problem of processing the land. Since most of the adjacent territory is allocated for a garden.

Processing by hand with ordinary country tools is very problematic. It takes enough to cultivate and level the soil a large number of time, and also the process takes a lot of effort.

The best solution to the problem would be to buy a walk-behind tractor, with its help you can cultivate the land in the shortest possible time, without the need to use physical force.

But, not everyone can afford to purchase this unit, since its cost is high. However, you can make a walk-behind tractor with your own hands. In terms of quality, it is in no way inferior to analogues that are sold in stores. And you can make it from improvised materials, which are usually a lot in summer cottages. The first such inventor was Valentin Arkhipov.

From scrap metal and a motor from a chainsaw, Druzhba was able to construct a walk-behind tractor that not only plowed the ground, but also spudded plantings. Next, consider how to make a walk-behind tractor according to the Arkhipov principle.

Design features

In the photo of the walk-behind tractor, it can be seen that the design has two wheels, an engine, a frame and chains. To create a walk-behind tractor does not require a lot of materials. As a rule, all of them are in sheds. Valentin Arkhipov took the engine from the VP-150M scooter, as it had a cooling system for the cylinder head using air.

The frame by the inventor was made of pipes, which had a U-shape. And also on the lathe for turning, an axle was made, on which the wheels were subsequently attached. Arkhipov made four rods for them - one main and three regulating ones, which connect the walk-behind tractor with the steering system and the plow.

On the device, the chain pitch is 12.7 mm and 15.9 mm. Number of teeth per sprocket:

secondary axis - 20, 60;
output axis - 11;
running axle - 40.

There are many similar devices that are created on the basis of the drawings of the Arkhipov walk-behind tractor. Since its unit has a number of undeniable advantages.

Tractors and tools that work the land are connected with hinges. This gives the walk-behind tractor more maneuverability. It can change the direction of travel without having to remove the plow from the furrow.

When cultivating the land with a walk-behind tractor, many are faced with the problem of skidding the unit to the side. Arkhipov decided this problem. He shifted the plow axis slightly to the left in relation to the direction of travel.

The inventor managed to make an automatic level of plowing depth. Which is very practical, since you do not need to lower or raise the plow yourself each time. Consequently, the cultivation of the land is much faster.

Instructions for creating an aggregate

First of all, you need to make a running shaft. To equip it, you need to connect it with bearings. After that, the star is welded, and overrunning clutches are installed.

They perform a differential function during the operation of the apparatus. At the end, the body is complemented by a motor mount and wheels. On the motor mount, you can fix the steering system, traction and hiller for a walk-behind tractor.

To connect the frame and the engine, two arc-shaped pipes are needed. Between which, when connecting, it is necessary to leave space for placing a container for fuel.

To connect the resulting structure, a special bracket is used, which is welded to the main part of the unit. Upon completion of all work, you can install the trailer on the walk-behind tractor.

Modernization of the walk-behind tractor

The adapter for the walk-behind tractor can be supplemented with various additional equipment. Which will not only plow the land, but also cultivate. Therefore, the Arkhipov walk-behind tractor is recognized as the most functional and practical.

Note!

Many use a walk-behind tractor not only for agricultural needs. They are very easy to clean adjoining territory from snow. To do this, it is only necessary to install an additional roller on the unit, and one more sprocket.

Like any equipment, the unit can fail, breakage occurs. However, the repair of walk-behind tractors is extremely simple. And there shouldn't be much difficulty in fixing it. So for repair you do not need special tools or additional equipment.

Motoblock photo

Note!

Many craftsmen use improvised devices to improve the walk-behind tractor already on the farm. Thanks to such improvements, the capabilities of the walk-behind tractor increase many times over. And in addition to automating various kinds of chores, the device will become an excellent assistant in construction, cargo transportation, etc. As a rule, for each walk-behind tractor you can pick up a lot attachments for harrowing, plowing, hilling, cultivation, and other plant care and tillage operations. And by adapting the hitch with the trolley, you have a full-fledged vehicle for the transportation of building materials, land, fertilizers and other goods. But not every walk-behind tractor can offer such an abundance of additional equipment, and if there is an opportunity to understaff, then, as a rule, its cost is disproportionately high.

In our article, we offer a universal and simple solution, namely, a home-made walk-behind tractor from a bridge from a Zhiguli.

What components are needed for a home-made walk-behind tractor from a bridge from a Zhiguli

The basis for the universal device will be a 1999 Ural motoblock cultivator, but you can use any other. Complete with the installation, metal wheels, milling cutters, a tiller and a plow were provided. We will not dwell on them, since they are all on sale at an affordable price.

But when it became necessary to build a house with a garage, it would be necessary to perform a lot of construction and preparatory work, as well as unloading and loading work: leveling the soil, filling trenches, transporting building materials, sand, earth, etc.

For comfortable movement on asphalt, classic old wheels from the Zhiguli were adapted. It is necessary to install them at a minimum distance from each other, this will greatly facilitate the control process.

A "shovel-bulldozer" was made to level the soil. To do this, we use a ready-made factory beam, where fasteners from tillers are provided. After that, we attach a metal sheet with a thickness of at least 8 mm to the remaining two curved strips, if less, then it will bend under load. This design will allow you to easily and quickly level the ground. If you need to fill up trenches or, say, rake garbage or earth into a pile, then you need to install a metal sheet in front of the walk-behind tractor.

As you can see, a home-made walk-behind tractor from a bridge from a Zhiguli with your own hands can be done quite simply. Now let's take a closer look at the process of creating a universal trailer for a walk-behind tractor.

Trailer

The old rear axle from the Zhiguli is best suited for a trailer from a walk-behind tractor, and a container pallet for steel sheets is also required.

Thanks to the universal winch on the trailer, you can easily load and unload items weighing up to 500 kg. In order to prevent the trailer from tipping over, it is necessary to place the transported cargo as close as possible to the front side of the trailer.

We make the walk-behind tractor safe

For safe use universal walk-behind tractor, it must be equipped with a mechanical brake, both left and right. For this, the brake pads of the bridge from the Zhiguli are best suited:

1. Remove the brake cylinders from the pads;
2. We make cuts in the "cheeks";
3. Next, attach the levers to the blocks;
4. We derive traction under the control of two pedals;

We install a lever with a ratchet, which will securely fix the walk-behind tractor during parking.

Without brakes on the installation it is impossible to transport a heavy load, since on the slopes of especially steep walk-behind tractors it becomes simply uncontrollable.

The presented design in the figure did an excellent job of pulling heavy telephone stepchildren left over from telegraph poles out of the ground. Such material is perfect for foundations and ceilings. The loading process is as follows:

We install a shovel in front of the post, then attach the end of the cable to the upper part, and below the hook with the block. It was possible to get and load two columns in one flight, the weight of each of them is about 250 kg. Poles must be loaded on the main frame.

The clay is still damp and stuck a little, but everything is getting enough sleep.

We make a fender liner for a walk-behind tractor (protection from dirt)

To prevent dirt and water from flying into your face during operation, you can make a homemade fender liner.

who made homemade trailers for a walk-behind tractor, which hubs and wheels were installed

Vladimir (Ansbert) Gogo has everything he has.

leonid (Addalyn) TO NOT GRIND.

Sergiy (Upendra) On the trailer of my MB, there is a rear beam "Moskvich" -2141, assembled

Alexander (Thomason) it will be hard

Basil (Agharna) The most best option this is a trailer from a motor scooter almost all year round, you just need to remove everything superfluous and weld a drawbar instead of the front end and you're done.

Well, if the problem is with a scooter, then a good option with rear suspensions from a front-wheel drive auto, well, for example, from our nine.

Sergey (Bruno) Front from the Cossack

Sergey (Bruno)

Sergey (Bruno) Front with Zhiguli

Sergey (Bruno)

Vyacheslav (Dulcinea) I have wheels from 3 d with which hubs they can be docked and how to make a brake

Ivan (Sealey) Wheels and hubs from agricultural machinery 4, 50x10 but no brakes.

Sergiy (Upendra) It's hard depending on which MB. I have a "Chinese" 8-strong, diesel. The MB itself weighs 220 kg, the trailer 300, a total of 520, but it pulls a ton, it has been checked, but this is in an emergency, and I have been driving within 500 - 700 kg for 3.5 years. We have very popular 8-10 strong, 6-speed "Chinese" diesel engines, viscous, hardy, easy to maintain.

Gennady (Honoura) I took the hubs and brake mechanisms from the car VAZ 2109. The trailer is self-made weighing about 100 kg. carries boldly. 500 kg. cargo

Gennady (Honoura) rear hubs.

Anatoly (Kellie) Great idea, in general the rear axles from front-wheel drive cars are ideal. You can make hydraulic brakes using the master cylinder from the clutch of the same VAZ - a classic, and make a handbrake.

Sergey (Bruno) and if you put the drive axle from the Vaz and make the drive from the pom, then any mountain will not care, but it goes through the mud like a tank.

Sergei (Bruno) NO! ON HARD SURFACE IT SHOULD BE DISCONNECTED.

Sergey (Bruno) THERE IS ANOTHER SECRET - I WILL PUT THE NIVA TRANSFER WITH AN INTER-AXLE DIFFERENTIAL UNDER THE TRAILER AND THERE WILL BE ALL-WHEEL DRIVE.

Nikolay (Baladhi) soon they will work out a new field, maybe it will be better

Tags: How to make a walk-behind tractor from a bridge from a vase

Rear axle VAZ 2101 shortened for walk-behind tractor

Our assistant MOTOBLOK | Topic author: Nikolay

Dnepr cargo motorcycle

Sergey (Kazuno) Dnepr-highway motorcycle. Without forced cooling with a load through the fields and forests.

Nikolay (Cramer) 3 years work Dnepr excellent temperature

Sanya (Chaviv) I want to make one for myself, only from Ural

Sanya (Chaviv) Tell me, what is the bridge made of?

Vladimir (Annamae) I think from the classics.

Vladimir (Annamae) Why do you remove comments?

Sanya (Chaviv) Can you supply a Muscovite with his own risors?

Eugene (Amadee) About 20 years ago, a man drove around the villages on a similar one, repairing sewing machines.

Eugene (Amadee) The duralumin van was larger than the heel.

Nikolay (Cramer) bridge vaz 2101

Sanya (Chaviv) And what kind of springs?

Nikolai (Cramer) Muscovite

Sanya (Chaviv) What about the brakes? On liquids?

Nicholas (Cramer) rope

Homemade walk-behind tractor based on the motorcycle Minsk and...

Apr 24, 2014 - Motoblock based on Minsk and the VAZ bridge... nothing shakes or dangles, well, what have you thought about what you will do from your bridge?)).

Rear axle VAZ 2101 shortened for motoblock...

DIMENSIONS for a track of 70 cm, we shorten the bridge of the vase - Duration: 2:18. Alexander Buek 617 views. 2:18. How to make a Trailer for Motoblock...

The trailer described below for a walk-behind tractor from the Zhiguli bridge makes it possible to load it up to 500 kg in order to prevent tipping, we load the load as much as possible to the beginning of the trailer.

How to make a trailer for a walk-behind tractor from the Zhiguli bridge

Made this trailer standard scheme(the frame is shown below), the only thing that was installed was the Zhiguli bridge, which made it possible to immediately make brakes on the trailer. We used this trailer to pull out of the ground concrete stepchildren from telegraph poles.

For one trip, it turns out to load 2 poles weighing 250 kg each. The movement was easy, it was possible to load more, but it's better not to risk it. The columns are loaded directly onto the frame.

The trailer is equipped with mechanical brakes - the brake drums of the Zhiguli bridge are used. The brake cylinders were removed, the handbrake cable was brought out to the pedals and attached. The walk-behind tractor is not equipped with brakes, so transporting goods on steep descents can become dangerous.

The body of a homemade motoblock trailer allows you to overturn the winch. The photo shows wet clay, but in general everything tips over perfectly. One more small improvement can be made. Make narrow fenders, their width should be 14 cm, then we attach them to the frame of the walk-behind tractor. Then we release the roller, it slows down on the rubber and does not hit the wing. We now attach regular ones to these fenders. They are easy to remove and reinstall (changing different wheels). Spray from the wheels does not fly in the face.

Welded frame for a trailer to a walk-behind tractor

We make a frame for a trailer for a walk-behind tractor from steel corners and pipes. The design is obtained with a margin of safety.
Frame design drawing for a homemade trailer.

1. - brace - corner size - 21x21x3,
2. - seat frame - corner size - 21x21x3,
3. - riser - pipe - 50x25x4,
4. - seat post - corner size - 40x40x4,
5. 14 - front struts - pipe dimensions - 50x25x25.
6.15 - longitudinal spars - corner dimensions - 40x40x4,
7.8 - right wheel axle supports - corner dimensions - 32x32x4,
9.16 - rear struts - pipe dimensions - 50x25,
10. - reinforcing cross member - corner dimensions - 40x40x4,
11. - longitudinal hinge body - pipe dimensions - 58x4,
12. - wheel axle - bar dimensions - 030, 13.
17 - transverse spars - corner dimensions - 40x40x4,
18. - scarves - (s4)

Do-it-yourself trailer hitch for a walk-behind tractor

A hitch is a mechanism that allows you to attach attachments to walk-behind tractors. In essence, a walk-behind tractor hitch can attach hillers, flat cutters, plows, potato diggers, trailers and a double hitch.

It is such a rigid hitch that is one of the most popular and rather popular attachments, which is most often installed by owners of private property.

Do-it-yourself trailer coupling for a walk-behind tractor is a very important component that ensures the reliability of the connections between the walk-behind tractor and trailed equipment. There are different types of hitch connections. And the difference is in what exactly you want to attach to the walk-behind tractor, in our case it is a trailer, so for it the U-shaped hitch assembly to the walk-behind tractor is very suitable for us.
The trailer hitch for a walk-behind tractor must be made sufficiently reliable so that it can withstand constant loads. Therefore, we recommend that it be made only from a durable brand of metal. The hitch is based on a U-shaped mount. To make it, a channel is suitable for us.

This mount must be installed at the rear of the walk-behind tractor under the steering wheel.
In the fastening of the walk-behind hitch, holes of a suitable diameter must be drilled in order to fix the bracket and the mounting pin in it. We take the pin from high-quality and high-strength steel. It will serve us for connecting additional devices to the walk-behind tractor.

The location of the bracket should be with its long end down, this is necessary so that the equipment that we connect to the walk-behind tractor performs all the necessary functions and the end of the bracket does not touch or bend.

This type of hitch connection for a walk-behind tractor is standard.
Before starting work, it is worth checking all threaded connections very carefully - they must be tightened to the stop. This simple procedure helps us prevent hitch failure, because a loose or disconnected connection can cause a breakdown.

After checking all the connections, you can safely get to work. First, it is worth remembering that the setting attachments in our case, this trailer still depends on the walk-behind tractor itself and its technical capabilities. After setting up the equipment, it is necessary to carry out trial work - very carefully monitor its operation in the range of 3-5 meters, and, if necessary, make additional adjustments.

Homemade brakes on a trailer to a walk-behind tractor photo drawings

Do-it-yourself trolley for a walk-behind tractor drawings, photos, videos

Doing homemade trailer and a do-it-yourself tow hitch for a walk-behind tractor