loops 

How to hang a door on hinges?

Any repair or replacement of the door leads to the fact that we need to dismantle it, and then hang a new structure. You can hang the door yourself or invite specialists for this work. will result in unnecessary spending. Therefore, if you are a jack of all trades, it is better, easier and cheaper to do it yourself.

Choosing loops

To choose the right number and types of loops, you need to take into account the size of the canvas, as well as the location of these same loops. If the design is double-leaf, then both wings are mounted on hinges on both sides. To hang a door with one leaf, correct calculations are required.

Correct installation

How to hang the door on hinges so that the whole structure is reliable and safe in operation? To do this, you need to prepare tools in the form of a plumb line, a level, a drill with a speed controller, a screwdriver, a chisel, a hammer and a tape measure. is conducted as follows:

  1. The distance from the upper and lower edges of the door leaf must be at least 20 cm.
  2. If there is a third loop, it should be placed in the middle between the first and second.
  3. If there are four hinges, then the height of the door is divided into 5 segments, on which the fittings are attached.
  4. The upper parts of the hinges are attached to the door leaf, and the lower parts (with rods) are attached to the frame.
  5. We apply the loop to the end of the canvas at a predetermined distance.
  6. We fasten the fittings to the door with self-tapping screws using a drill or screwdriver. It is important that the diameter of the drill is thinner than the diameter of the screw, which will ensure that the hinges are securely fixed.
  7. Now we install the door in the box, open it slightly and supplement one of the canopies with the lower part of the hinge so that it fits snugly against the box. We circle this place with a pencil, in the same way we repeat the steps with the rest of the loops. Now the door can be removed.

To hang the doors with your own hands as accurately as possible, you need to remove the top layer of wood in the places that are circled. In the resulting recess, the lower canopies of the loops will be attached. It is important that they are located horizontally, then the door will open easily and smoothly.

Checking the door

After the hinges are installed and the door is hung, you need to check its performance. If suddenly a creak is heard when opening or closing, we lubricate the hinges with some kind of composition - machine oil, grease, technical petroleum jelly. If the hinges are cut too deep, do not despair: this situation can be corrected by using a rubber gasket, thick cardboard or hardboard.

If the canvas in the end turned out to be too low, and therefore scratches the floor, you need to raise it. To do this, a washer is placed between the canopies of the loop, after which the entire structure rises. As you can see, hanging a door is not as difficult as it seems, especially if you approach this process responsibly and pay timely attention to each defect.

We hang the doors on the cabinet

It seems to many that installing a door, hanging hinges is not an easy process. But in fact, all the work can be done independently. To perform the work, you need to prepare mounting foam, anchor bolts and screws, a level, a chisel, a hacksaw for wood and a miter box. How to hang doors on a wardrobe? For this, several rules must be followed.


Features of working with a coupe

Each type of cabinet from a constructive point of view has its own characteristics, which is expressed in the need for proper hinges. Most often, furniture has hinged doors, but wardrobes are no less popular. With its equipment, the following types of loops are most often used:

We act according to the rules!

How to hang a door on a wardrobe? It is worth starting by measuring the width and height of each opening and frame, checking the level of the roof, sidewalls and the shield that will serve as the floor. The thickness of the walls of the cabinet should also be measured, since distortions may form in them over time. Misalignment compensation is possible thanks to overhead loops that are easy to adjust. It is important to ensure that all structural elements are at the same depth during installation. Installation of loops is carried out in the following order.

  1. The hinges are applied to the place where they will be attached, holes are marked and drilled to a depth of 20-30 mm.
  2. Holes are made both at the ends of the sidewall and on the door itself.
  3. The hinge halves are fixed with furniture screws.
  4. The door is hung.

Difficulties of work

Many are interested in the question of how to hang a compartment door if there are internal drawers next to them. In this case, shelves, drawers, which are located on the inside, should be somewhat shorter in depth than the external elements. During installation, attention should also be paid to the fact that dead zones may form at the intersection of the frames. If they get hit, then in this case it will be impossible to open them, and they will lose their functionality. In general, experts do not recommend installing compartment doors on their own, since each sliding system has its own characteristics, a rigid binding of the door to the frame, and therefore you can simply ruin the furniture.

We follow the steps

Whatever door you hang - in a doorway or closet, you need to do it in accordance with a number of steps. Only in this way will the hinges be cut neatly and accurately, and the door will serve stably and properly. So, if you are installing a new design, you will first have to start assembling the box. To do this, the side and top racks are cut out, which are connected with self-tapping screws.

When assembling the box, you need to leave a gap of at least 5 mm - thanks to it, the doors will not be subjected to friction and looping after installation. After the box is ready, you can already mount the hinges. But here there are some nuances. For example, it is important to understand how much the door has - the number of hinges that will be required during its installation depends on this. The box can be fixed in two ways. The first involves the use of foam, if the door is lightweight, and the second - anchors, which is advisable for large-sized structures. All openings can be neatly closed with decorative plugs.

Most of the work can be done on your own, but since it is not so easy to hang a closet door, it is better to entrust this work to professional craftsmen.