doors 

Do-it-yourself lamp made of pvc pipes. Do-it-yourself lamps and lamps from pipes: four simple instructions Pipe floor lamp

Production of lamps from brass to order. All products, after manufacturing, are treated with a special protective agent so that the brass does not darken.

Manufacture of a lamp made of brass with glass shades.
The glass elements were made to order in a glass workshop. The g9 LED bulb is inside a brass cone.

Development of a chandelier drawing Glass shades for G4 base Connection of brass pipes


Brass chandelier "Five corners".
Description and dimensions are given in the drawing. Polished brass surface. The drawing of the chandelier was developed based on the visualization.

Development of a chandelier drawing Custom made brass chandelier Base for lamp E14 Chandelier made of brass pipes


Production of lamps for the hotel.
Rings made of brass strip (brass thickness 2 mm, width 30 mm) are patinated only on the outside, the inner surface is polished brass (it looks lighter in the photo). Acrylic pipe with a diameter of 200 mm and a height of 840 mm. Installed in the NOVOTEL hotel (Moscow, Novoslobodskaya st. 23)

Luminaire according to the design project Acrylic pipe d-200 mm Patinated brass Installed in NOVOTEL hotel


Wall lamps in polished brass.
Three lamps were made to order with diameters: 400, 700 (pictured) and 1000 mm. The cross section of the rings is 40x40 mm. In the close-up photo, you can see how the joint looks on the case and evaluate the quality of grinding.

Production of brass lamps Ring diameter 700 mm Polished brass.


Lamps with a lens.
The project of the luminaire was developed on the basis of visualization. Power consumption 3 W, luminous flux 300 Lm. The surface of the brass is ground and then treated with a protective agent.

brass lamps drawing of fixtures light passes through the lens


Lamp ring made of brass.
Ring lamp made of polished brass for the network of branches of the bank "UralSib". These lamps are installed in the cities: St. Petersburg, Moscow, Rostov-on-Don, Nizhnevartovsk, Yekaterinburg, Chelyabinsk. Diameter 800 mm, ring section 50x50 mm. Power - 60 watts.

brass ring lamp brushed brass office lamp


Lamp-mirror made of patinated brass.
It is a ring lamp that shines on the wall. Mirror in the center. The diameter of the ring is 1000 mm, the section of the ring (WxH) is 50x70 mm. Three mounting points on the wall through an acrylic diffuser. Power consumption - 30 W, luminous flux - 2900 lm.

lamp-mirror brass lamp brass wall sconce


Lamps from brass pipes.
Pipes with a diameter of 50 mm, which are mounted on a rod from a pipe of 25 mm. The height of the luminaire is 1000 mm, the diameter of the ceiling bowl is 200 mm. The power consumption of the lamp is 18 W, the luminous flux is 1500 lm. Light sources are LEDs. Direction of light up and down.

brass lamp brass lamp degree of patination of brass


Sconce in brushed, patinated brass.
Direction of light up and down. Pipe diameter - 50 mm, height - 485 mm. Power - 6 W, luminous flux 500 lm. For comparison, the third photo is a similar sconce made of polished brass without patina.

patinated brass wall lamp brass wall lamp polished brass wall lamp


details before patination brass lamp brass lamp


Hanger "Planck" made of brass to order
Details are shown in the drawing below. The hanging height can be adjusted. Base E27.

Making a brass hanger Brass hanger drawing
Custom made brass fixtures


Brass sconce
Dimensions are shown on the drawing. Two lamps for E14 base.

Sconce drawing brass sconce Base E14


Production of brass lamps to order
and brass sconces were made according to the design project.

Design project Production of brass lamps Dimensions: diameter 75 mm, height 220 mm


Pendant "Drop".
Hanging height is adjustable. The g9 base bulb is inside a brass cone.

Suspension Drop Suspension drawing Thin section brass


Wall lamp "Eclipse"
Made on the basis of visualization. Diameter 500 mm, thickness 70 mm. Facing with natural veneer. Light reflected from the wall.

Reflected light illumination Custom wall lamp Veneer lining of the lamp


Lamp - tubes of polished brass.
Made to order. Attached is a drawing with description and dimensions. The surface of the brass is covered with a special protective composition so that it does not darken over time. The photos were taken in our production.

lamp drawing polished brass pipes brass tube lamp


We mainly produce lamps in the style of: loft, minimalism, hi-tech and other modern design trends.

To place an order, send an application (drawing or sketch) to info@site

For a true jack of all trades, the remains of building material are a real treasure. From a pile of rubbish, he is able to create masterpieces suitable for interior decoration and useful for everyday use. Remains of plastic, plumbing fittings, plugs, metal fasteners are enough to create a beautiful and functional pipe lamp that can be hung on the wall or used instead of a table lamp.

If the finished product seems unpretentious to you, you can complicate its design by adding metal parts - pipes, bolts, nuts, fitting legs

Self-assembly of lamps from pipes

Even people who do not know the basics of plumbing can build a product from pipe sections, metal and plastic parts, and it will not be difficult for specialists involved in laying communications every day to come up with their own, unique, interesting options. The suggested instructions are just examples of how quickly and easily unnecessary materials can be turned into useful things.

A plumber's dream - a lamp from a water pipe

For the device of household communications, polypropylene is increasingly being used - a durable, flexible, reliable material that does not lend itself to rust, which has been performing its functions for decades. Systems are installed instead of obsolete metal pipelines, which are dismantled and thrown into a landfill. Let's take a few used iron parts and make a concise, convenient lighting fixture out of them.

We will need:

  • 1 pipe of arbitrary length;
  • 2 flanges for stands;
  • cross as a connecting element;
  • 2 knees;
  • electrical cord with switch;
  • lamp (energy-saving or LED);
  • cartridge, clutch for fixing.

If the base diameter is 20 mm, respectively, the rest of the parts have the same cross section.

Strictly technical, rough lamps and cozy home floor lamps are all made from ordinary water pipes.

The assembly process is simple. We connect the knees and flanges with the cross - the stand is ready. We insert the pipe from above, then fasten the coupling. We pass the wires, be sure to make insulation, since the metal conducts current, we screw in the light bulb. A few simple manipulations - and the original lamp made of water pipes is ready!

In order to give the old details an aesthetically attractive look, we clean all the elements with fine sandpaper, cover with paint for metal.

Video: Functional robot lamp made of pipes and fittings

Wall lamp made of flexible metal-plastic

For the wall version, a more dynamic tubular LED lamp is needed, which can be directed in different directions, and here metal-plastic products will come in handy. Unlike plastic parts, they are durable, have elasticity, in other words, they bend.

The ability to bend and take on various shapes will help make the lamp unique

The base, which is mounted on the wall, for convenience, is best made from a piece of wood - solid pine, birch blanks, a fragment of thick plywood. We drill a hole in it for a flexible element. From a small bar we grind the body for the cartridge, given that a movable fragment will be attached on the other side.

A ready-made pipe wall lamp is a great backlight for paintings or photographs

All that's left is to assemble. We insert an electric wire, previously threaded through the base, into a metal-plastic blank (from 20 to 50 cm long), fix the cartridge and produce insulation. We fix the base on the wall, screw the LED element and enjoy the effect. It remains to be added that the flexible tube for the lamp can be turned in any direction, and if desired, even tied in a knot, if the length allows.

The cost of metal-plastic products of medium diameter is low - from 60 to 100 rubles per linear meter

Video: Plastic pipe LED lamp

Three-arm horizontal illumination

A convenient lamp made of several movable copper tubes on a metal base can create full-fledged lighting for a small room or a backlight for paintings, photographs, collages or shelves with souvenirs.

To work, you will need pieces of metal pipes of the same diameter, copper bending tubes for making horns, several tees (according to the number of horns), a half-flange (for fixing the lamp on a wall or ceiling), plugs, electrical wire and fasteners. You will also need lamps - it is better to take LED ones that do not heat the surrounding parts and the illuminated surface.

The tool needed for assembly is in every home:

  • jigsaw or hacksaw for metal;
  • pliers;
  • screwdriver;
  • drill and thin drills;
  • insulating material;
  • paint on metal, brush.

First you need to prepare the copper tubes, then unscrew the base and finally assemble everything into a single structure. We make horns for lamps from copper blanks 30-40 cm long. To do this, they need to be gently bent so that they take the form of a smooth arc. Beware of creases, as the corners on the tubes will spoil the appearance of the structure and will prevent the electrical wire from being threaded. We wind the compression fittings on the ends, thread the wires, fix and isolate the cartridges.

We clean the metal pieces, paint, after drying we twist a long pole out of them. We attach copper horns to it at regular intervals, not forgetting about the safe connection of electrical wires. We fix a do-it-yourself lamp made of pipes on a wall or ceiling so that the rays illuminate the desired area, screw in the bulbs and check. The design in a trendy industrial style is ready.

Plastic Tube LED Night Light

Plastic is easy to process, so there are plenty of opportunities for decorating ceiling lamps and lampshades made from this malleable material. Openwork lamps made of plastic and polypropylene pipes are installed on the floor, on the table, used as a table lamp, night light.

Beautiful designer lamp made of plastic elements and multi-colored light bulbs

We stock up on plastic blanks, get to work. The best option is products with a diameter of at least 15 cm, so that the walls of the finished lampshade do not come into contact with the lamp, even if it is LED. From the tools you will need a drill with various nozzles, drills, a clerical knife, a construction hair dryer.

Operating procedure:

  • We are preparing the base - a heavy stand with a fixed cartridge, we are supplying an electrical wire. Suitable wooden block or construction of several parts.
  • From a thick pvc pipe we cut out a segment 20-30 cm in height, we process the edges - this is the future lampshade.
  • We apply an image on a plastic surface using a stencil - an ornament, a drawing, a pattern.
  • Using a drill, knife, scalpel, we cut out the extra parts, making cuts, cuts, through holes. We leave some parts translucent, reducing the thickness of the material. We heat with a hairdryer to bend or deform the necessary elements.
  • We install the lampshade on the base, turn on the lamp.

Video: Table lamp made of polypropylene pipes and fittings

White, not suitable for a bedroom or living room, the color of the plastic can be changed to a brighter shade by painting the surface of the lampshade with special acrylic paints. Finished lamps made of PVC pipes look just magical.

To connect the elements we use threads, bolts and nuts

Taking a cue from designers

The use of old unnecessary things to create unique interior items has long been of interest to designers, engineers, and self-taught craftsmen. Metal and plastic pipes turned out to be a convenient material for creating various lamps, chandeliers, table lamps, floor lamps, sconces. Some of them look modern, suitable for decorating high-tech offices and rooms, while others, elegant and stylish, are appropriate for a modern interior.

Elaborately carved flowers and butterflies transform a plastic pipe into an amazing decoration.

It is curious that magnificent design items that cost a lot of money are assembled from the most common building materials, which means that each of you, if desired, can create your own unique masterpiece, which is not inferior to well-known analogues either in appearance or in functionality.

We often come across articles that describe how you can create unusual, but at the same time useful things for your house or apartment from unnecessary materials that, for example, were left after repairs. Also, crafts can be made from plastic bottles, disposable tableware, corks and the like. But in this article we will talk about material such as PVC pipes, which, according to the rules, are needed and used in the sewer system, but now we will describe how to make a useful thing out of this material, such as a PVC pipe lamp.

From a completely simple and inexpensive material, you can create something fabulous and fantastic, the most important thing here is to have skillful hands and a rich imagination, the rest is up to the small. Thanks to these good qualities, you can create beautiful and beautiful night lights in the form of lamps.

In fact, we don’t know who first thought of this idea and created such beauty as a lamp made of PVC pipes, but nowadays people of such nationalities as Brazilians, Argentines, Australians and Chinese are engaged in such needlework, but ours is no exception. country Russia.

To carry out a beautiful craft, we will list the materials and tools that we will need during the work:

1. A drill with a sufficient and diverse set of nozzles that have different thicknesses and can still be distinguished by the types of grinding, we need abrasive ground tips.

2. PVC pipe. When choosing, you need to take into account the size, that is, the diameter, it should be in the range from 25 to 55 centimeters. At the same time, provide for a place in which your night light will stand or hang and the dimensions of the pattern that you will cut out on the pipeline.

PVC pipe wireless lamp

If you do not want to spend a lot of time and effort on making a pipe lamp, then the work can be done with just one drill. But if you want to make a drawing that is voluminous and complex in its composition, then for this you need to include in the work the execution of small to large holes, complex rhinestones, working with the thickness of the pipe walls, removing the outer layers to add volume and aesthetics and, of course, giving the effect 3D to some details.

Before we start making patterns and rhinestones on a lighting device, let's decide what size we need a lamp. The main criteria for pipe size are its diameter and height. If you have decided on the size of the craft, then let's move on to choosing templates and stencils for the desired picture that you want to depict on your device. As patterns, a floral look of a picture, a landscape or a banal ornament, and the like, the choice of your taste can serve.

The silhouette of the selected pattern is transferred to the pipe in a very simple, but at the same time convenient method, at the same time, attention is paid to the edges at the top and bottom. Before you begin, consider the desired size of the holes in the pipe in diameter so that the drills fit your ideas. A very simple option can serve as a good idea, for example, you don’t need to draw and cut out various patterns, you can simply cut out a beautiful decorative lamp using the drawn holes of various diameters.

A very elegant drawing is obtained when light halftones are used in the work. Such an effect and quality can be obtained when the outer layer of the pipe, that is, PVC, is removed with the help of abrasive tips. The more layers you remove, the greater the transparent effect will be and the light will be much brighter in these places than on a simple surface.

To give the lamp made of PVC pipes the effect of 3D format, it is necessary to attach the parts that will protrude beyond the walls of the pipe, first you need to thin them with the same tips that were used when adding a light halftone, after doing these works we cut out the shape with special construction knife.

To give aesthetics and the final effect, we take a building hair dryer (it gives more intense heat), heat the form to a state of elasticity and bend it to the side. We leave the mold alone and wait for it to cool, when it cools it will remain in the same state in which you bent it during heating.

Such a lamp at the end of the work can not even be painted, the natural color of the pipes (white) will fit into the design of your house or apartment quite easily. But still, if you want to give the lamp a color design, then it will not take much time and a lot of effort, you just need paint from an aerosol can.

Upon completion of work from the sphere of scenery, it is worth moving on to works that will answer all practical questions. So, for the completed crafts, you need a very strong and stable shelf or base, at your discretion, because the lamp made of PVC pipes must stand steadily, since it weighs a lot and is also rather big in size.

As a light in your device, there can be various types of lighting using lamps. It is recommended to use energy-saving lamps, because they will not allow the walls of the lamp made of PVC pipes to overheat and deform the decorative shell. To give a more decorative lamp, you can use a garland during lighting, it will turn out very interesting.

Today, the topic of creating all kinds of table lamps and lamps is quite popular, the main task of their manufacture is, of course, uniqueness, so that this product is one of a kind. The "Loft" style is quite fashionable today, but designer pieces in this style cost a lot of money. It is quite possible to make them yourself, for example, the author made a table lamp from copper tubes, fittings, made a stand from wood, connected the pieces of tubes through the fittings and stretched the wire, connected the cartridge with a relay and a lamb to control the brightness of the glow, screwed in the Edison lamp. Previously, the cartridge was painted in copper color to match the pipe. Wooden stand covered with stain and varnish.

And so, let's look at what exactly is needed to create a table lamp?

materials

1. copper tube 12mm
2. copper fittings
3. glue
4. wire
5. Edison lamp
6. cartridge with relay and lamb for adjusting the glow of the lamp
7. spray paint (copper color)
8. board 13x25x5 cm
9. stain
10. varnish

Tools

1. drill
2. pipe cutter
3. pliers
4. screwdriver
5. brush
6. ruler
7. sandpaper

Step-by-step instructions for making a table lamp from copper tubes with your own hands.

First of all, prepare all the listed tools and materials so that you have everything at hand and in plain sight, so as not to miss the details during assembly.

Then you need a board measuring 13x25x5 cm, it should be well sanded with sandpaper, and then covered with stain in several layers with periodic drying of the surface.

After that, it is necessary to drill a hole with a diameter of 19 mm, but only to the middle of the board.

We drag the wire through the end hole.

Screw the adapter into the top hole with a wrench.

We cut the copper tube into pieces with a pipe cutter.

The length of the blanks should be as follows: 35, 15, 5, 6 cm.

Then we drag the wire through a long tube and connect it to the adapter. In this spirit, with the help of fittings, the entire base of the table lamp is assembled.

We disassemble the cartridge and connect the wires.

We do not touch the paper spacer, because it serves as an insulator.

That's basically all, the copper tube lamp is ready, you can screw in the Edison lamp.